The Linux Kernel Mailing List
 help / color / mirror / Atom feed
From: Yixun Lan <dlan@kernel.org>
To: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-kernel@vger.kernel.org, Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Paul Walmsley <pjw@kernel.org>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>,
	Alexandre Ghiti <alex@ghiti.fr>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>,
	"open list:RISC-V ARCHITECTURE" <linux-riscv@lists.infradead.org>,
	"open list:RISC-V SPACEMIT SoC Support"
	<spacemit@lists.linux.dev>
Subject: Re: [PATCH v2 5/5] riscv: dts: spacemit: improve RTL8211F PHY configuration on K3 Pico-ITX board
Date: Tue, 7 Jul 2026 07:56:42 +0000	[thread overview]
Message-ID: <20260707075642-GKG35811@kernel.org> (raw)
In-Reply-To: <20260623204431.498700-6-aurelien@aurel32.net>

Hi Aurelien,

On 22:43 Tue 23 Jun     , Aurelien Jarno wrote:
> Vendor kernel enabled ALDPS (Advanced Link Down Power Saving) on the
> RTL8211F PHY to save power when link down.
for ALDPS, tested here do noticed it will configure RTL8211F PHY's
 RTL8211F_PHYCR1 register via rtl8211f_config_aldps()

And plug out then in the cable, the network(eth0) will come back and still
works fine, although I have no power consumption meter to test, but I think
 it deserves:

Tested-by: Yixun Lan <dlan@kernel.org>

> 
> Vendor kernel also disabled the 125MHz clkout clock signal, and indeed
> the schematics confirms that it only goes to a test point (TP14), so
> let's do the same.
> 
> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
> ---
>  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> index bf64b6c6f867f..e12d798b48a49 100644
> --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> @@ -234,6 +234,8 @@ phy0: phy@1 {
>  			reset-gpios = <&gpio 0 15 GPIO_ACTIVE_LOW>;
>  			reset-assert-us = <10000>;
>  			reset-deassert-us = <10000>;
> +			realtek,aldps-enable;
> +			realtek,clkout-disable;
>  		};
>  	};
>  };
> -- 
> 2.53.0
> 

-- 
Yixun Lan (dlan)

  reply	other threads:[~2026-07-07  7:56 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-06-23 20:43 [PATCH v2 0/5] riscv: dts: spacemit: serial/i2c/ethernet improvements for the K3 Pico-ITX board Aurelien Jarno
2026-06-23 20:43 ` [PATCH v2 1/5] riscv: dts: spacemit: set console baud rate on " Aurelien Jarno
2026-06-23 20:43 ` [PATCH v2 2/5] riscv: dts: spacemit: enable the i2c2 adapter " Aurelien Jarno
2026-06-23 20:43 ` [PATCH v2 3/5] riscv: dts: spacemit: add 24c02 eeprom " Aurelien Jarno
2026-06-23 20:43 ` [PATCH v2 4/5] riscv: dts: spacemit: add i2c aliases " Aurelien Jarno
2026-06-23 20:43 ` [PATCH v2 5/5] riscv: dts: spacemit: improve RTL8211F PHY configuration " Aurelien Jarno
2026-07-07  7:56   ` Yixun Lan [this message]
2026-07-07  6:18 ` [PATCH v2 0/5] riscv: dts: spacemit: serial/i2c/ethernet improvements for the " Yixun Lan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260707075642-GKG35811@kernel.org \
    --to=dlan@kernel.org \
    --cc=alex@ghiti.fr \
    --cc=aou@eecs.berkeley.edu \
    --cc=aurelien@aurel32.net \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=palmer@dabbelt.com \
    --cc=pjw@kernel.org \
    --cc=robh@kernel.org \
    --cc=spacemit@lists.linux.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox