From: Hillf Danton <hdanton@sina.com>
To: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>,
K Prateek Nayak <kprateek.nayak@amd.com>,
Christoph Lameter <cl@gentwo.org>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH RFC] sched/fair: decline WF_SYNC stacking when waker LLC is the busier share
Date: Fri, 7 Aug 2026 06:53:50 +0800 [thread overview]
Message-ID: <20260806225352.981-1-hdanton@sina.com> (raw)
In-Reply-To: <87mruz2lfx.fsf@intel.com>
On Thu, 06 Aug 2026 10:44:18 -0700 Vinicius Costa Gomes wrote:
>Hillf Danton <hdanton@sina.com> writes:
>> On Tue, 04 Aug 2026 16:14:05 -0700 Vinicius Costa Gomes wrote:
>>> Since commit 900bbaae67e9 ("epoll: Add synchronous wakeup support for
>>> ep_poll_callback"), epoll driven WF_SYNC wakeups have been "too
>>> strong" and could cause tasks to stack on a busy NUMA node while other
>>> nodes are relatively idle.
>>>
>>> As commit 900bbaae67e9 ("epoll: Add synchronous wakeup support for
>>> ep_poll_callback") improves real workloads a revert is not the answer.
>>> The fix is to make the WF_SYNC "stack on waker" shortcut take into
>>> account the load on this and prev's LLC, rejecting the shortcut only
>>> when the waker (this) LLC is fully loaded and prev's LLC is less
>>> loaded than the waker's.
>>>
>>> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
>>> ---
>>> We received a report of a regression on a openresty based
>>> workload (the main metric being tail latencies) on a CWF SNC3 single
>>> socket system, the main symptom that we could measure was one node
>>> being overloaded while the other nodes were relatively idle.
>>>
>>> Further investigation showed that spreading the NIC RX interrupts over
>>> all NUMA nodes helped. Reverting commit 900bbaae67e9 ("epoll: Add
>>> synchronous wakeup support for ep_poll_callback") also helped.
>>>
>> The irq approach is prefered because anything that gets the eevdf offloaded
>> is good, you see it is near to the knowall point, needless to say that they
>> lie in different layers and from the scheduling-cpu pov irq is a gray rhino
>> in the room while WF_SYNC is a tiger mosquito in the corner at best in your
>> case where the mosquito failed to understand your workload.
>
> I don't think irq spreading across NUMA nodes is that good of an idea on
> low loads/by default, as it loses the locality that the kernel (even
> with irqbalance) try to maintain. I used that as a hackish way of
> testing "if I spread tasks, does it improve the tail latencies?".
>
Can you specify the root cause of the tail latencies, particularly after
spending two minutes thinking if changing config in user space to solve the
issue is a light year better than adding a couple lines of code in the
wakeup path?
> Note that the "local-only reproducer" workload (memcached +
> memtier_benchmark) runs over loopback (no NIC irqs here), I pin memtier
> (the client) to one NUMA node, leave the server unpinned and I am able
> to reproduce the issue: with the RFC patch the tail latencies reduce by
> 2-3x. (on the customer workload the impact is even higher)
>
> My expectation was that the scheduler would be able to say: "ugh, even
> though respecting WF_SYNC is good most of the cases, this isn't one of
No comment before root cause specified, even if I suspect it sounds like
that two CPU cores could not provide line speed 24-port 1000MB ether switch
before 2010 while 12 cores could.
> them". And this is the spirit of the RFC, showing that those cases
> exist and their impact.
>
>
>Cheers,
>--
>Vinicius
next prev parent reply other threads:[~2026-08-06 22:59 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-04 23:14 [PATCH RFC] sched/fair: decline WF_SYNC stacking when waker LLC is the busier share Vinicius Costa Gomes
2026-08-05 2:14 ` Hillf Danton
2026-08-06 17:44 ` Vinicius Costa Gomes
2026-08-06 22:53 ` Hillf Danton [this message]
2026-08-06 23:22 ` Vinicius Costa Gomes
2026-08-07 5:17 ` Hillf Danton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260806225352.981-1-hdanton@sina.com \
--to=hdanton@sina.com \
--cc=cl@gentwo.org \
--cc=kprateek.nayak@amd.com \
--cc=linux-kernel@vger.kernel.org \
--cc=peterz@infradead.org \
--cc=vinicius.gomes@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox