[PATCH v3 1/5] ARM: dts: aspeed: santabarbara: Add system monitoring GPIOs

[Fred Chen <fredchen.openbmc@gmail.com>]

Add several GPIO expanders on the switch board for NIC, PEX, and cable
presence monitoring. Due to a design change, ioexp0 (0x20) now
aggregates interrupts from the downstream expanders (0x21-0x27) onto a
single sgpiom0 line, reducing the number of sideband interrupt pins
required.

The new nodes provide:
- NIC1-4 power good monitoring, reset control, and fault detection
- Switch PEX power good signals and hardware SKU/Revision IDs
- Cable presence detection and selection for four SPI flashes
- System power fault alert via SGPIO and E1S GPIO expander interrupt

Signed-off-by: Fred Chen <fredchen.openbmc@gmail.com>
---
 .../aspeed-bmc-facebook-santabarbara.dts      | 125 +++++++++++++++++-
 1 file changed, 124 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
index 0a3e2e241063..2a822e38f091 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
@@ -616,6 +616,8 @@ gpio@74 {
 				reg = <0x74>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <146 IRQ_TYPE_LEVEL_LOW>;
 				gpio-line-names =
 					"P12V_E1S_ADC_ALERT","BUFF0_100M_LOSB_PLD",
 					"E1S_BP_SKU_ID0","E1S_BP_SKU_ID1",
@@ -1335,6 +1337,112 @@ eeprom@50 {
 &i2c12 {
 	status = "okay";
 
+	ioexp0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <148 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"IOEXP_21h_INT_N","IOEXP_22h_INT_N",
+			"IOEXP_23h_INT_N","IOEXP_24h_INT_N",
+			"IOEXP_25h_INT_N","IOEXP_26h_INT_N",
+			"IOEXP_27h_INT_N","SWB_PWR_FAULT_N",
+			"","","","",
+			"","","","";
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&ioexp0>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"PDB_PRSNT_J1_N","PDB_PRSNT_J2_N",
+			"PRSNT_NIC1_N","PRSNT_NIC2_N",
+			"PRSNT_NIC3_N","PRSNT_NIC4_N",
+			"","",
+			"CBL_PRSNT_MCIO_0_N","CBL_PRSNT_MCIO_1_N",
+			"CBL_PRSNT_MCIO_2_N","CBL_PRSNT_MCIO_3_N",
+			"","","","";
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&ioexp0>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"SWB_PWRGD_P3V3_AUX","SWB_PWRGD_P1V8_PEX",
+			"SWB_PWRGD_P1V8_AUX","SWB_PWRGD_P5V",
+			"SWB_PWRGD_P1V5_PEX","SWB_PWRGD_P1V2_PEX",
+			"SWB_PWRGD_P0V895_PEX","SWB_PWRGD_P0V81_PEX_0",
+			"SWB_PWRGD_P0V81_PEX_1","SWB_PWRGD_P0V81_REFCLK",
+			"SWB_PWRGD_MODULE","",
+			"","","","";
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&ioexp0>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"RST_PERST_NIC1_N","RST_PERST_NIC2_N",
+			"RST_PERST_NIC3_N","RST_PERST_NIC4_N",
+			"RST_PERST_MCIO_0_N","RST_PERST_MCIO_1_N",
+			"RST_PERST_MCIO_2_N","RST_PERST_MCIO_3_N",
+			"FM_P3V3_NIC1_FAULT_N","FM_P3V3_NIC2_FAULT_N",
+			"FM_P3V3_NIC3_FAULT_N","FM_P3V3_NIC4_FAULT_N",
+			"PWRGD_P12V_NIC1","PWRGD_P12V_NIC2",
+			"PWRGD_P12V_NIC3","PWRGD_P12V_NIC4";
+	};
+
+	gpio@25 {
+		compatible = "nxp,pca9555";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&ioexp0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"NIC1_MAIN_R_PWR_EN","NIC2_MAIN_R_PWR_EN",
+			"NIC3_MAIN_R_PWR_EN","NIC4_MAIN_R_PWR_EN",
+			"FM_PLD_NIC1_AUX_PWR_EN","FM_PLD_NIC2_AUX_PWR_EN",
+			"FM_PLD_NIC3_AUX_PWR_EN","FM_PLD_NIC4_AUX_PWR_EN",
+			"PWRGD_NIC1","PWRGD_NIC2",
+			"PWRGD_NIC3","PWRGD_NIC4",
+			"PWRGD_P3V3_NIC1","PWRGD_P3V3_NIC2",
+			"PWRGD_P3V3_NIC3","PWRGD_P3V3_NIC4";
+	};
+
+	gpio@26 {
+		compatible = "nxp,pca9555";
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&ioexp0>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"SWB_SKU_ID_0","SWB_SKU_ID_1",
+			"SWB_SKU_ID_2","SWB_SKU_ID_3",
+			"SWB_REV_ID_0","SWB_REV_ID_1",
+			"SWB_REV_ID_2","",
+			"RST_PLD_PEX_PERST_N","CPLD_MB_PWR_EN",
+			"RST_PERST_SWB_R_N","SWB_LEAK_DETECT",
+			"PEX_SYS_ERR_FPGA","PRSNT_SWB_LEAK_CABLE_N",
+			"","";
+	};
+
 	gpio@27 {
 		compatible = "nxp,pca9555";
 		reg = <0x27>;
@@ -1349,6 +1457,21 @@ gpio@27 {
 			"SPI_MUX_SEL","","","";
 	};
 
+	gpio@28 {
+		compatible = "nxp,pca9555";
+		reg = <0x28>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"SCO_UART_MUX_SEL0","SCO_UART_MUX_SEL1",
+			"SPI_PROG_PL12_SEL","SPI_PROG_PL34_SEL",
+			"","","","",
+			"I3C_HUB_3_MUX_SEL_PLD","",
+			"SPI_PROG_PL12_EN_N","SPI_PROG_PL34_EN_N",
+			"SCO1_SPI_SEL","SCO2_SPI_SEL",
+			"SCO3_SPI_SEL","SCO4_SPI_SEL";
+	};
+
 	// SWB FRU
 	eeprom@52 {
 		compatible = "atmel,24c64";
@@ -1776,7 +1899,7 @@ &sgpiom0 {
 	"MB_SKU_ID_1","PASSWORD_CLEAR",
 	"MB_SKU_ID_2","",
 	"MB_SKU_ID_3","",
-	"","BIOS_DEBUG_MODE",
+	"SYS_PWR_FAULT_ALERT","BIOS_DEBUG_MODE",
 	/*H0-H3 line 112-119*/
 	"FM_IOEXP_U538_INT_N","",
 	"FM_IOEXP_U539_INT_N","FM_MODULE_PWR_EN_N_1B",
-- 
2.52.0