[PATCH v2 0/7] Rockchip: add Rockchip rk3576 EVB1 board

[PATCH v2 0/7] Rockchip: add Rockchip rk3576 EVB1 board

[Kever Yang]

This patch set is for rockchip rk3576 evb1.
Based on the naneng combphy patch from Frank Wang.

This version including the patch adding usb nodes from Frank Wang.

Changes in v2:
- update the clock and reset names to pass the DTB CHECK
- remove required 'msi-map'
- add interrupt name 'msi'
- Update clock and reset names and sequence to pass DTB check
- collect acked-by tag
- Enable USB nodes

Frank Wang (1):
  arm64: dts: rockchip: add usb related nodes for rk3576

Kever Yang (6):
  dts: arm64: rockchip: Add rk3576 naneng combphy nodes
  dt-bindings: PCI: dwc: rockchip: Add rk3576 support
  dts: arm64: rockchip: Add rk3576 pcie nodes
  dt-bindings: arm: rockchip: Sort for rk3568 evb
  dt-bindings: arm: rockchip: Add rk3576 evb1 board
  arm64: dts: rockchip: Add rk3576 evb1 board

 .../devicetree/bindings/arm/rockchip.yaml     |  25 +-
 .../bindings/pci/rockchip-dw-pcie-common.yaml |   1 +
 .../bindings/pci/rockchip-dw-pcie.yaml        |   4 +-
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3576-evb1-v10.dts     | 727 ++++++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3576.dtsi      | 278 +++++++
 6 files changed, 1023 insertions(+), 13 deletions(-)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts

-- 
2.25.1

[PATCH v2 1/7] dts: arm64: rockchip: Add rk3576 naneng combphy nodes

[Kever Yang]

rk3576 has two naneng combo phy,
- combophy0 is used for one of pcie and sata;
- combophy1 is used for one of pcie, sata and usb3;

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

Changes in v2:
- update the clock and reset names to pass the DTB CHECK

 arch/arm64/boot/dts/rockchip/rk3576.dtsi | 36 ++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
index 436232ffe4d1..a147879da501 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
@@ -1587,6 +1587,42 @@ uart11: serial@2afd0000 {
 			status = "disabled";
 		};
 
+		combphy0_ps: phy@2b050000 {
+			compatible = "rockchip,rk3576-naneng-combphy";
+			reg = <0x0 0x2b050000 0x0 0x100>;
+			#phy-cells = <1>;
+			clocks = <&cru CLK_REF_PCIE0_PHY>,
+				 <&cru PCLK_PCIE2_COMBOPHY0>,
+				 <&cru PCLK_PCIE0>;
+			clock-names = "ref", "apb", "pipe";
+			assigned-clocks = <&cru CLK_REF_PCIE0_PHY>;
+			assigned-clock-rates = <100000000>;
+			resets = <&cru SRST_PCIE0_PIPE_PHY>,
+				 <&cru SRST_P_PCIE2_COMBOPHY0>;
+			reset-names = "phy", "apb";
+			rockchip,pipe-grf = <&php_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy0_grf>;
+			status = "disabled";
+		};
+
+		combphy1_psu: phy@2b060000 {
+			compatible = "rockchip,rk3576-naneng-combphy";
+			reg = <0x0 0x2b060000 0x0 0x100>;
+			#phy-cells = <1>;
+			clocks = <&cru CLK_REF_PCIE1_PHY>,
+				 <&cru PCLK_PCIE2_COMBOPHY1>,
+				 <&cru PCLK_PCIE1>;
+			clock-names = "ref", "apb", "pipe";
+			assigned-clocks = <&cru CLK_REF_PCIE1_PHY>;
+			assigned-clock-rates = <100000000>;
+			resets = <&cru SRST_PCIE1_PIPE_PHY>,
+				 <&cru SRST_P_PCIE2_COMBOPHY1>;
+			reset-names = "phy", "apb";
+			rockchip,pipe-grf = <&php_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
+			status = "disabled";
+		};
+
 		sram: sram@3ff88000 {
 			compatible = "mmio-sram";
 			reg = <0x0 0x3ff88000 0x0 0x78000>;
-- 
2.25.1

[PATCH v2 2/7] dt-bindings: PCI: dwc: rockchip: Add rk3576 support

[Kever Yang]

rk3576 is using dwc controller, but use msi interrupt instead of its,
so the msi-map is not required, and need to add a new 'msi' interrupt name.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

Changes in v2:
- remove required 'msi-map'
- add interrupt name 'msi'

 .../devicetree/bindings/pci/rockchip-dw-pcie-common.yaml      | 1 +
 Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml   | 4 +---
 2 files changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
index cc9adfc7611c..e5e1a2c7ae05 100644
--- a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
+++ b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
@@ -81,6 +81,7 @@ properties:
       - const: msg
       - const: legacy
       - const: err
+      - const: msi
       - const: dma0
       - const: dma1
       - const: dma2
diff --git a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml
index 550d8a684af3..9a464731fa4a 100644
--- a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml
@@ -26,6 +26,7 @@ properties:
       - const: rockchip,rk3568-pcie
       - items:
           - enum:
+              - rockchip,rk3576-pcie
               - rockchip,rk3588-pcie
           - const: rockchip,rk3568-pcie
 
@@ -71,9 +72,6 @@ properties:
 
   vpcie3v3-supply: true
 
-required:
-  - msi-map
-
 unevaluatedProperties: false
 
 examples:
-- 
2.25.1

[PATCH v2 3/7] dts: arm64: rockchip: Add rk3576 pcie nodes

[Kever Yang]

rk3576 has two pcie controller, both are pcie2x1 used with
naneng-combphy.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

Changes in v2:
- Update clock and reset names and sequence to pass DTB check

 arch/arm64/boot/dts/rockchip/rk3576.dtsi | 109 +++++++++++++++++++++++
 1 file changed, 109 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
index a147879da501..df7dfe702221 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
@@ -1016,6 +1016,115 @@ qos_npu_m1ro: qos@27f22100 {
 			reg = <0x0 0x27f22100 0x0 0x20>;
 		};
 
+		pcie0: pcie@2a200000 {
+			compatible = "rockchip,rk3576-pcie", "rockchip,rk3568-pcie";
+			bus-range = <0x0 0xf>;
+			clocks = <&cru ACLK_PCIE0_MST>, <&cru ACLK_PCIE0_SLV>,
+				 <&cru ACLK_PCIE0_DBI>, <&cru PCLK_PCIE0>,
+				 <&cru CLK_PCIE0_AUX>;
+
+			clock-names = "aclk_mst", "aclk_slv",
+				      "aclk_dbi", "pclk",
+				      "aux";
+			device_type = "pci";
+			interrupts = <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "sys", "pmc", "msg", "legacy", "err", "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+					<0 0 0 2 &pcie0_intc 1>,
+					<0 0 0 3 &pcie0_intc 2>,
+					<0 0 0 4 &pcie0_intc 3>;
+			linux,pci-domain = <0>;
+			num-ib-windows = <8>;
+			num-viewport = <8>;
+			num-ob-windows = <2>;
+			max-link-speed = <2>;
+			num-lanes = <1>;
+			phys = <&combphy0_ps PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+			power-domains = <&power RK3576_PD_PHP>;
+			ranges = <0x01000000 0x0 0x20100000 0x0 0x20100000 0x0 0x00100000
+				  0x02000000 0x0 0x20200000 0x0 0x20200000 0x0 0x00e00000
+				  0x03000000 0x9 0x00000000 0x9 0x00000000 0x0 0x80000000>;
+			reg = <0x0 0x22000000 0x0 0x00400000>,
+			      <0x0 0x2a200000 0x0 0x00010000>,
+			      <0x0 0x20000000 0x0 0x00100000>;
+			reg-names = "dbi", "apb", "config";
+			resets = <&cru SRST_PCIE0_POWER_UP>, <&cru SRST_P_PCIE0>;
+			reset-names = "pwr", "pipe";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			status = "disabled";
+
+			pcie0_intc: legacy-interrupt-controller {
+				interrupt-controller;
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 280 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
+		pcie1: pcie@2a210000 {
+			compatible = "rockchip,rk3576-pcie", "rockchip,rk3568-pcie";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			bus-range = <0x20 0x2f>;
+			clocks = <&cru ACLK_PCIE1_MST>, <&cru ACLK_PCIE1_SLV>,
+				 <&cru ACLK_PCIE1_DBI>, <&cru PCLK_PCIE1>,
+				 <&cru CLK_PCIE1_AUX>;
+			clock-names = "aclk_mst", "aclk_slv",
+				      "aclk_dbi", "pclk",
+				      "aux";
+			device_type = "pci";
+			interrupts = <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "sys", "pmc", "msg", "legacy", "err", "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+					<0 0 0 2 &pcie1_intc 1>,
+					<0 0 0 3 &pcie1_intc 2>,
+					<0 0 0 4 &pcie1_intc 3>;
+			linux,pci-domain = <0>;
+			num-ib-windows = <8>;
+			num-viewport = <8>;
+			num-ob-windows = <2>;
+			max-link-speed = <2>;
+			num-lanes = <1>;
+			phys = <&combphy1_psu PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+			power-domains = <&power RK3576_PD_SUBPHP>;
+			ranges = <0x01000000 0x0 0x21100000 0x0 0x21100000 0x0 0x00100000
+				  0x02000000 0x0 0x21200000 0x0 0x21200000 0x0 0x00e00000
+				  0x03000000 0x9 0x80000000 0x9 0x80000000 0x0 0x80000000>;
+			reg = <0x0 0x22400000 0x0 0x00400000>,
+			      <0x0 0x2a210000 0x0 0x00010000>,
+			      <0x0 0x21000000 0x0 0x00100000>;
+			reg-names = "dbi", "apb", "config";
+			resets = <&cru SRST_PCIE1_POWER_UP>, <&cru SRST_P_PCIE1>;
+			reset-names = "pwr", "pipe";
+			status = "disabled";
+
+			pcie1_intc: legacy-interrupt-controller {
+				interrupt-controller;
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 266 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
 		gmac0: ethernet@2a220000 {
 			compatible = "rockchip,rk3576-gmac", "snps,dwmac-4.20a";
 			reg = <0x0 0x2a220000 0x0 0x10000>;
-- 
2.25.1

[PATCH v2 4/7] arm64: dts: rockchip: add usb related nodes for rk3576

[Kever Yang]

From: Frank Wang <frank.wang@rock-chips.com>

This adds USB and USB-PHY related nodes for RK3576 SoC.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

Changes in v2: None

 arch/arm64/boot/dts/rockchip/rk3576.dtsi | 133 +++++++++++++++++++++++
 1 file changed, 133 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
index df7dfe702221..5be316684be4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
@@ -445,6 +445,58 @@ soc {
 		#size-cells = <2>;
 		ranges;
 
+		usb_drd0_dwc3: usb@23000000 {
+			compatible = "rockchip,rk3576-dwc3", "snps,dwc3";
+			reg = <0x0 0x23000000 0x0 0x400000>;
+			clocks = <&cru CLK_REF_USB3OTG0>,
+				 <&cru CLK_SUSPEND_USB3OTG0>,
+				 <&cru ACLK_USB3OTG0>;
+			clock-names = "ref_clk", "suspend_clk", "bus_clk";
+			interrupts = <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&power RK3576_PD_USB>;
+			resets = <&cru SRST_A_USB3OTG0>;
+			dr_mode = "otg";
+			phys = <&u2phy0_otg>, <&usbdp_phy PHY_TYPE_USB3>;
+			phy-names = "usb2-phy", "usb3-phy";
+			phy_type = "utmi_wide";
+			snps,dis_enblslpm_quirk;
+			snps,dis-u1-entry-quirk;
+			snps,dis-u2-entry-quirk;
+			snps,dis-u2-freeclk-exists-quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-hs-quirk;
+			snps,parkmode-disable-ss-quirk;
+			status = "disabled";
+		};
+
+		usb_drd1_dwc3: usb@23400000 {
+			compatible = "rockchip,rk3576-dwc3", "snps,dwc3";
+			reg = <0x0 0x23400000 0x0 0x400000>;
+			clocks = <&cru CLK_REF_USB3OTG1>,
+				 <&cru CLK_SUSPEND_USB3OTG1>,
+				 <&cru ACLK_USB3OTG1>;
+			clock-names = "ref_clk", "suspend_clk", "bus_clk";
+			interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&power RK3576_PD_PHP>;
+			resets = <&cru SRST_A_USB3OTG1>;
+			dr_mode = "otg";
+			phys = <&u2phy1_otg>, <&combphy1_psu PHY_TYPE_USB3>;
+			phy-names = "usb2-phy", "usb3-phy";
+			phy_type = "utmi_wide";
+			snps,dis_enblslpm_quirk;
+			snps,dis-u1-entry-quirk;
+			snps,dis-u2-entry-quirk;
+			snps,dis-u2-freeclk-exists-quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,dis_rxdet_inp3_quirk;
+			snps,parkmode-disable-hs-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dma-coherent;
+			status = "disabled";
+		};
+
 		sys_grf: syscon@2600a000 {
 			compatible = "rockchip,rk3576-sys-grf", "syscon";
 			reg = <0x0 0x2600a000 0x0 0x2000>;
@@ -515,6 +567,65 @@ usbdpphy_grf: syscon@2602c000 {
 			reg = <0x0 0x2602c000 0x0 0x2000>;
 		};
 
+		usb2phy_grf: syscon@2602e000 {
+			compatible = "rockchip,rk3576-usb2phy-grf", "syscon", "simple-mfd";
+			reg = <0x0 0x2602e000 0x0 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u2phy0: usb2-phy@0 {
+				compatible = "rockchip,rk3576-usb2phy";
+				reg = <0x0 0x10>;
+				resets = <&cru SRST_OTGPHY_0>, <&cru SRST_P_USBPHY_GRF_0>;
+				reset-names = "phy", "apb";
+				clocks = <&cru CLK_PHY_REF_SRC>,
+					 <&cru ACLK_MMU2>,
+					 <&cru ACLK_SLV_MMU2>;
+				clock-names = "phyclk", "aclk", "aclk_slv";
+				clock-output-names = "usb480m_phy0";
+				#clock-cells = <0>;
+				status = "disabled";
+
+				u2phy0_otg: otg-port {
+					#phy-cells = <0>;
+					interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "otg-bvalid", "otg-id", "linestate";
+					status = "disabled";
+				};
+			};
+
+			u2phy1: usb2-phy@2000 {
+				compatible = "rockchip,rk3576-usb2phy";
+				reg = <0x2000 0x10>;
+				resets = <&cru SRST_OTGPHY_1>, <&cru SRST_P_USBPHY_GRF_1>;
+				reset-names = "phy", "apb";
+				clocks = <&cru CLK_PHY_REF_SRC>,
+					 <&cru ACLK_MMU1>,
+					 <&cru ACLK_SLV_MMU1>;
+				clock-names = "phyclk", "aclk", "aclk_slv";
+				clock-output-names = "usb480m_phy1";
+				#clock-cells = <0>;
+				status = "disabled";
+
+				u2phy1_otg: otg-port {
+					#phy-cells = <0>;
+					interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "otg-bvalid", "otg-id", "linestate";
+					status = "disabled";
+				};
+			};
+		};
+
+		vo1_grf: syscon@26036000 {
+			compatible = "rockchip,rk3576-vo1-grf", "syscon";
+			reg = <0x0 0x26036000 0x0 0x100>;
+			clocks = <&cru PCLK_VO1_ROOT>;
+		};
+
 		sdgmac_grf: syscon@26038000 {
 			compatible = "rockchip,rk3576-sdgmac-grf", "syscon";
 			reg = <0x0 0x26038000 0x0 0x1000>;
@@ -1732,6 +1843,28 @@ combphy1_psu: phy@2b060000 {
 			status = "disabled";
 		};
 
+		usbdp_phy: phy@2b010000 {
+			compatible = "rockchip,rk3576-usbdp-phy";
+			reg = <0x0 0x2b010000 0x0 0x10000>;
+			#phy-cells = <1>;
+			clocks = <&cru CLK_PHY_REF_SRC >,
+				 <&cru CLK_USBDP_COMBO_PHY_IMMORTAL>,
+				 <&cru PCLK_USBDPPHY>,
+				 <&u2phy0>;
+			clock-names = "refclk", "immortal", "pclk", "utmi";
+			resets = <&cru SRST_USBDP_COMBO_PHY_INIT>,
+				 <&cru SRST_USBDP_COMBO_PHY_CMN>,
+				 <&cru SRST_USBDP_COMBO_PHY_LANE>,
+				 <&cru SRST_USBDP_COMBO_PHY_PCS>,
+				 <&cru SRST_P_USBDPPHY>;
+			reset-names = "init", "cmn", "lane", "pcs_apb", "pma_apb";
+			rockchip,u2phy-grf = <&usb2phy_grf>;
+			rockchip,usb-grf = <&usb_grf>;
+			rockchip,usbdpphy-grf = <&usbdpphy_grf>;
+			rockchip,vo-grf = <&vo1_grf>;
+			status = "disabled";
+		};
+
 		sram: sram@3ff88000 {
 			compatible = "mmio-sram";
 			reg = <0x0 0x3ff88000 0x0 0x78000>;
-- 
2.25.1

[PATCH v2 5/7] dt-bindings: arm: rockchip: Sort for rk3568 evb

[Kever Yang]

The info for rk3568 should before rk3588.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---

Changes in v2:
- collect acked-by tag

 .../devicetree/bindings/arm/rockchip.yaml     | 20 +++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 753199a12923..45ee4bf7c80c 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -1006,6 +1006,16 @@ properties:
           - const: rockchip,rk3399-sapphire-excavator
           - const: rockchip,rk3399
 
+      - description: Rockchip RK3566 BOX Evaluation Demo board
+        items:
+          - const: rockchip,rk3566-box-demo
+          - const: rockchip,rk3566
+
+      - description: Rockchip RK3568 Evaluation board
+        items:
+          - const: rockchip,rk3568-evb1-v10
+          - const: rockchip,rk3568
+
       - description: Rockchip RK3588 Evaluation board
         items:
           - const: rockchip,rk3588-evb1-v10
@@ -1099,16 +1109,6 @@ properties:
           - const: zkmagic,a95x-z2
           - const: rockchip,rk3318
 
-      - description: Rockchip RK3566 BOX Evaluation Demo board
-        items:
-          - const: rockchip,rk3566-box-demo
-          - const: rockchip,rk3566
-
-      - description: Rockchip RK3568 Evaluation board
-        items:
-          - const: rockchip,rk3568-evb1-v10
-          - const: rockchip,rk3568
-
       - description: Sinovoip RK3308 Banana Pi P2 Pro
         items:
           - const: sinovoip,rk3308-bpi-p2pro
-- 
2.25.1

[PATCH v2 6/7] dt-bindings: arm: rockchip: Add rk3576 evb1 board

[Kever Yang]

Add device tree documentation for rk3576-evb1-v10.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---

Changes in v2:
- collect acked-by tag

 Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 45ee4bf7c80c..b2681a45867b 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -1016,6 +1016,11 @@ properties:
           - const: rockchip,rk3568-evb1-v10
           - const: rockchip,rk3568
 
+      - description: Rockchip RK3576 Evaluation board
+        items:
+          - const: rockchip,rk3576-evb1-v10
+          - const: rockchip,rk3576
+
       - description: Rockchip RK3588 Evaluation board
         items:
           - const: rockchip,rk3588-evb1-v10
-- 
2.25.1

[PATCH v2 7/7] arm64: dts: rockchip: Add rk3576 evb1 board

[Kever Yang]

RK3576 EVB1 board features:
- Rockchip RK3576
- PMIC: RK806-2x2pcs+DiscretePower
- RAM: LPDDR4/4x 2pcsx 32bit
- ROM: eMMC5.1 + UFS
- LAN x 2
- HDMI TX
- SD card slot
- PCIe2 slot

Add support for pmic, eMMC, SD-card, ADC-KEY, PCIE and GMAC.

NOTE: The board has a hardware mux design for
- PCIe slot(pcie1)
- USB3 host(usb_drd1_dwc3)
and default state is switch to USB3. To enable PCIe slot:
- hardware: Switch the mux to PCIe side;
- dts: disable usb_drd1_dwc3 and enable pcie1;

Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

Changes in v2:
- Enable USB nodes

 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3576-evb1-v10.dts     | 727 ++++++++++++++++++
 2 files changed, 728 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 86cc418a2255..2e683d7eab58 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-sige7.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-w3.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-cm5-evb.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
new file mode 100644
index 000000000000..edbc46e6cf12
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-evb1-v10.dts
@@ -0,0 +1,727 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3576.dtsi"
+
+/ {
+	model = "Rockchip RK3576 EVB V10 Board";
+	compatible = "rockchip,rk3576-evb1-v10", "rockchip,rk3576";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial0:1500000n8";
+	};
+
+	adc_keys: adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-vol-up {
+			label = "volume up";
+			linux,code = <KEY_VOLUMEUP>;
+			press-threshold-microvolt = <17000>;
+		};
+
+		button-vol-down {
+			label = "volume down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			press-threshold-microvolt = <417000>;
+		};
+
+		button-menu {
+			label = "menu";
+			linux,code = <KEY_MENU>;
+			press-threshold-microvolt = <890000>;
+		};
+
+		button-back {
+			label = "back";
+			linux,code = <KEY_BACK>;
+			press-threshold-microvolt = <1235000>;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		work_led: led-0 {
+			gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vcc12v_dcin: regulator-vcc12v-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_device: regulator-vcc5v0-device {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_device";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_2v0_pldo_s3";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <2000000>;
+		regulator-max-microvolt = <2000000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc3v3_rtc_s5: regulator-vcc3v3-rtc-s5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_rtc_s5";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_1v8_s0: regulator-vcc-1v8-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_s3>;
+	};
+
+	vcc_3v3_s0: regulator-vcc-3v3-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc_ufs_s0: regulator-vcc-ufs-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_ufs_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc1v8_ufs_vccq2_s0: regulator-vcc1v8-ufs-vccq2-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8_ufs_vccq2_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_s3>;
+	};
+
+	vcc1v2_ufs_vccq_s0: regulator-vcc1v2-ufs-vccq-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v2_ufs_vccq_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc3v3_lcd_n: regulator-vcc3v3-lcd0-n {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_lcd0_n";
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc_3v3_s0>;
+	};
+
+	vcc3v3_pcie0: regulator-vcc3v3-pcie0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_host: regulator-vcc5v0-host {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc5v0_device>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_host_pwren>;
+	};
+
+	vbus5v0_typec: regulator-vbus5v0-typec {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus5v0_typec";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc5v0_device>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_otg0_pwren>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&combphy1_psu {
+	status = "okay";
+};
+
+&gmac0 {
+	phy-mode = "rgmii-rxid";
+	clock_in_out = "output";
+
+	snps,reset-gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 20000 100000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&eth0m0_miim
+		     &eth0m0_tx_bus2
+		     &eth0m0_rx_bus2
+		     &eth0m0_rgmii_clk
+		     &eth0m0_rgmii_bus
+		     &ethm0_clk0_25m_out>;
+
+	tx_delay = <0x21>;
+
+	phy-handle = <&rgmii_phy0>;
+	status = "okay";
+};
+
+&gmac1 {
+	phy-mode = "rgmii-rxid";
+	clock_in_out = "output";
+
+	snps,reset-gpio = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 20000 100000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&eth1m0_miim
+		     &eth1m0_tx_bus2
+		     &eth1m0_rx_bus2
+		     &eth1m0_rgmii_clk
+		     &eth1m0_rgmii_bus
+		     &ethm0_clk1_25m_out>;
+
+	tx_delay = <0x20>;
+
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk806: pmic@23 {
+		compatible = "rockchip,rk806";
+		reg = <0x23>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+
+		system-power-controller;
+
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc_sys>;
+		vcc10-supply = <&vcc_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs1_slp: dvs1-slp-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs1_pwrdn: dvs1-pwrdn-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs1_rst: dvs1-rst-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs2_slp: dvs2-slp-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs2_pwrdn: dvs2-pwrdn-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs2_rst: dvs2-rst-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs2_dvs: dvs2-dvs-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun4";
+		};
+
+		rk806_dvs2_gpio: dvs2-gpio-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun5";
+		};
+
+		rk806_dvs3_slp: dvs3-slp-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs3_pwrdn: dvs3-pwrdn-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs3_rst: dvs3-rst-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs3_dvs: dvs3-dvs-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun4";
+		};
+
+		rk806_dvs3_gpio: dvs3-gpio-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun5";
+		};
+
+		regulators {
+			vdd_cpu_big_s0: dcdc-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_big_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_npu_s0: dcdc-reg2 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_npu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_gpu_s0: dcdc-reg5 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vddq_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_logic_s0: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <800000>;
+				regulator-name = "vdd_logic_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vdd2_ddr_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdd_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo2_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdda_1v2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_3v3_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo6_s3: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo6_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v75_hdmi_s0: nldo-reg3 {
+				regulator-boot-on;
+				regulator-min-microvolt = <837500>;
+				regulator-max-microvolt = <837500>;
+				regulator-name = "vdda0v75_hdmi_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_0v85_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v75_s0: nldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdda_0v75_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&mdio0 {
+	rgmii_phy0: phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		clocks = <&cru REFCLKO25M_GMAC0_OUT>;
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		clocks = <&cru REFCLKO25M_GMAC1_OUT>;
+	};
+};
+
+&pinctrl {
+	usb {
+		usb_host_pwren: usb-host-pwren {
+			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb_otg0_pwren: usb-otg0-pwren {
+			rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbc0_int: usbc0-int {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&sdmmc {
+	max-frequency = <200000000>;
+	no-sdio;
+	no-mmc;
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	sd-uhs-sdr104;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&pcie1 {
+	reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie0>;
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vcca_1v8_s0>;
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	phy-supply = <&vbus5v0_typec>;
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usbdp_phy {
+	rockchip,dp-lane-mux = <2 3>;
+	status = "okay";
+};
+
+&usb_drd0_dwc3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_drd1_dwc3 {
+	dr_mode = "host";
+	status = "okay";
+};
-- 
2.25.1

Re: [PATCH v2 2/7] dt-bindings: PCI: dwc: rockchip: Add rk3576 support

[Rob Herring (Arm)]

On Fri, 20 Dec 2024 18:15:46 +0800, Kever Yang wrote:
> rk3576 is using dwc controller, but use msi interrupt instead of its,
> so the msi-map is not required, and need to add a new 'msi' interrupt name.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
> Changes in v2:
> - remove required 'msi-map'
> - add interrupt name 'msi'
> 
>  .../devicetree/bindings/pci/rockchip-dw-pcie-common.yaml      | 1 +
>  Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml   | 4 +---
>  2 files changed, 2 insertions(+), 3 deletions(-)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-ep.example.dtb: pcie-ep@fe150000: interrupt-names:5: 'msi' was expected
	from schema $id: http://devicetree.org/schemas/pci/rockchip-dw-pcie-ep.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-ep.example.dtb: pcie-ep@fe150000: interrupt-names:6: 'dma0' was expected
	from schema $id: http://devicetree.org/schemas/pci/rockchip-dw-pcie-ep.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-ep.example.dtb: pcie-ep@fe150000: interrupt-names:7: 'dma1' was expected
	from schema $id: http://devicetree.org/schemas/pci/rockchip-dw-pcie-ep.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-ep.example.dtb: pcie-ep@fe150000: interrupt-names:8: 'dma2' was expected
	from schema $id: http://devicetree.org/schemas/pci/rockchip-dw-pcie-ep.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-ep.example.dtb: pcie-ep@fe150000: Unevaluated properties are not allowed ('power-domains' was unexpected)
	from schema $id: http://devicetree.org/schemas/pci/rockchip-dw-pcie-ep.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241220101551.3505917-3-kever.yang@rock-chips.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v2 5/7] dt-bindings: arm: rockchip: Sort for rk3568 evb

[Diederik de Haas]

[-- Attachment #1: Type: text/plain, Size: 2307 bytes --]

Hi Kever,

On Fri Dec 20, 2024 at 11:15 AM CET, Kever Yang wrote:
> The info for rk3568 should before rk3588.

Indeed, so thanks for this patch.

> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> ---
>
> Changes in v2:
> - collect acked-by tag
>
>  .../devicetree/bindings/arm/rockchip.yaml     | 20 +++++++++----------
>  1 file changed, 10 insertions(+), 10 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
> index 753199a12923..45ee4bf7c80c 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.yaml
> +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
> @@ -1006,6 +1006,16 @@ properties:
>            - const: rockchip,rk3399-sapphire-excavator
>            - const: rockchip,rk3399
>  
> +      - description: Rockchip RK3566 BOX Evaluation Demo board
> +        items:
> +          - const: rockchip,rk3566-box-demo
> +          - const: rockchip,rk3566
> +
> +      - description: Rockchip RK3568 Evaluation board
> +        items:
> +          - const: rockchip,rk3568-evb1-v10
> +          - const: rockchip,rk3568
> +
>        - description: Rockchip RK3588 Evaluation board
>          items:
>            - const: rockchip,rk3588-evb1-v10
> @@ -1099,16 +1109,6 @@ properties:
>            - const: zkmagic,a95x-z2
>            - const: rockchip,rk3318
>  
> -      - description: Rockchip RK3566 BOX Evaluation Demo board
> -        items:
> -          - const: rockchip,rk3566-box-demo
> -          - const: rockchip,rk3566
> -
> -      - description: Rockchip RK3568 Evaluation board
> -        items:
> -          - const: rockchip,rk3568-evb1-v10
> -          - const: rockchip,rk3568
> -

While you're fixing the sorting order of these 2 Rockchip items, it
would be great if "Sinovoip RK3308 Banana Pi P2 Pro", "Sinovoip RK3568
Banana Pi R2 Pro" and "Sonoff iHost Smart Home Hub" could also be moved
into their correctly sorted position. A quick scan seems to indicate
that all the other items are properly sorted.

Cheers,
  Diederik

>        - description: Sinovoip RK3308 Banana Pi P2 Pro
>          items:
>            - const: sinovoip,rk3308-bpi-p2pro


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 3/7] dts: arm64: rockchip: Add rk3576 pcie nodes

[Krzysztof Kozlowski]

On Fri, Dec 20, 2024 at 06:15:47PM +0800, Kever Yang wrote:
> rk3576 has two pcie controller, both are pcie2x1 used with
> naneng-combphy.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---

Please use subject prefixes matching the subsystem. You can get them for
example with 'git log --oneline -- DIRECTORY_OR_FILE' on the directory
your patch is touching. For bindings, the preferred subjects are
explained here:
https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html#i-for-patch-submitters


> 
> Changes in v2:
> - Update clock and reset names and sequence to pass DTB check
> 
>  arch/arm64/boot/dts/rockchip/rk3576.dtsi | 109 +++++++++++++++++++++++
>  1 file changed, 109 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> index a147879da501..df7dfe702221 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> @@ -1016,6 +1016,115 @@ qos_npu_m1ro: qos@27f22100 {
>  			reg = <0x0 0x27f22100 0x0 0x20>;
>  		};
>  
> +		pcie0: pcie@2a200000 {
> +			compatible = "rockchip,rk3576-pcie", "rockchip,rk3568-pcie";
> +			bus-range = <0x0 0xf>;

Follow DTS coding style in properties order and everything around here.

Best regards,
Krzysztof

Re: [PATCH v2 2/7] dt-bindings: PCI: dwc: rockchip: Add rk3576 support

[Krzysztof Kozlowski]

On Fri, Dec 20, 2024 at 06:15:46PM +0800, Kever Yang wrote:
> rk3576 is using dwc controller, but use msi interrupt instead of its,
> so the msi-map is not required, and need to add a new 'msi' interrupt name.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
> Changes in v2:
> - remove required 'msi-map'
> - add interrupt name 'msi'
> 
>  .../devicetree/bindings/pci/rockchip-dw-pcie-common.yaml      | 1 +
>  Documentation/devicetree/bindings/pci/rockchip-dw-pcie.yaml   | 4 +---
>  2 files changed, 2 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
> index cc9adfc7611c..e5e1a2c7ae05 100644
> --- a/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
> +++ b/Documentation/devicetree/bindings/pci/rockchip-dw-pcie-common.yaml
> @@ -81,6 +81,7 @@ properties:
>        - const: msg
>        - const: legacy
>        - const: err
> +      - const: msi

ABI break without clear reasons.

Best regards,
Krzysztof

Re: [PATCH v2 3/7] dts: arm64: rockchip: Add rk3576 pcie nodes

[Kever Yang]

Hi Krzysztof,

On 2024/12/22 14:38, Krzysztof Kozlowski wrote:
> On Fri, Dec 20, 2024 at 06:15:47PM +0800, Kever Yang wrote:
>> rk3576 has two pcie controller, both are pcie2x1 used with
>> naneng-combphy.
>>
>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>> ---
> Please use subject prefixes matching the subsystem. You can get them for
> example with 'git log --oneline -- DIRECTORY_OR_FILE' on the directory
> your patch is touching. For bindings, the preferred subjects are
> explained here:
> https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html#i-for-patch-submitters
>
Will update with arm64: dts: .
>> Changes in v2:
>> - Update clock and reset names and sequence to pass DTB check
>>
>>   arch/arm64/boot/dts/rockchip/rk3576.dtsi | 109 +++++++++++++++++++++++
>>   1 file changed, 109 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
>> index a147879da501..df7dfe702221 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
>> +++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
>> @@ -1016,6 +1016,115 @@ qos_npu_m1ro: qos@27f22100 {
>>   			reg = <0x0 0x27f22100 0x0 0x20>;
>>   		};
>>   
>> +		pcie0: pcie@2a200000 {
>> +			compatible = "rockchip,rk3576-pcie", "rockchip,rk3568-pcie";
>> +			bus-range = <0x0 0xf>;
> Follow DTS coding style in properties order and everything around here.

I can do it for most of the properties, but is there any other rules 
other than sort,

eg. compatible and reg in the beginning and status in the end?


Thanks,

- Kever

>
> Best regards,
> Krzysztof
>
>

Re: [PATCH v2 3/7] dts: arm64: rockchip: Add rk3576 pcie nodes

[Heiko Stübner]

Am Montag, 23. Dezember 2024, 11:49:23 CET schrieb Kever Yang:
> Hi Krzysztof,
> 
> On 2024/12/22 14:38, Krzysztof Kozlowski wrote:
> > On Fri, Dec 20, 2024 at 06:15:47PM +0800, Kever Yang wrote:
> >> rk3576 has two pcie controller, both are pcie2x1 used with
> >> naneng-combphy.
> >>
> >> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> >> ---
> > Please use subject prefixes matching the subsystem. You can get them for
> > example with 'git log --oneline -- DIRECTORY_OR_FILE' on the directory
> > your patch is touching. For bindings, the preferred subjects are
> > explained here:
> > https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html#i-for-patch-submitters
> >
> Will update with arm64: dts: .
> >> Changes in v2:
> >> - Update clock and reset names and sequence to pass DTB check
> >>
> >>   arch/arm64/boot/dts/rockchip/rk3576.dtsi | 109 +++++++++++++++++++++++
> >>   1 file changed, 109 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> >> index a147879da501..df7dfe702221 100644
> >> --- a/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> >> +++ b/arch/arm64/boot/dts/rockchip/rk3576.dtsi
> >> @@ -1016,6 +1016,115 @@ qos_npu_m1ro: qos@27f22100 {
> >>   			reg = <0x0 0x27f22100 0x0 0x20>;
> >>   		};
> >>   
> >> +		pcie0: pcie@2a200000 {
> >> +			compatible = "rockchip,rk3576-pcie", "rockchip,rk3568-pcie";
> >> +			bus-range = <0x0 0xf>;
> > Follow DTS coding style in properties order and everything around here.
> 
> I can do it for most of the properties, but is there any other rules 
> other than sort,
> 
> eg. compatible and reg in the beginning and status in the end?

correct, that is the preferred sorting :-) .


Heiko