From: Dave Airlie <airlied@gmail.com>
To: Lobiuc Andrei <alobiuc@yahoo.com>
Cc: linux-kernel@vger.kernel.org
Subject: Re: PROBLEM: Radeon card displays incorrectly under the 2.6.11 version unless compiled with SMP support
Date: Tue, 8 Mar 2005 09:38:04 +1100 [thread overview]
Message-ID: <21d7e997050307143832a8239c@mail.gmail.com> (raw)
In-Reply-To: <20050306174932.56406.qmail@web30909.mail.mud.yahoo.com>
On Sun, 6 Mar 2005 09:49:32 -0800 (PST), Lobiuc Andrei
<alobiuc@yahoo.com> wrote:
> 1.Radeon card displays incorrectly under the 2.6.11
> version unless compiled with SMP support.
> 2.After compiling and installing the 2.6.11 kernel
> version, my ASUS Radeon 9200SE 128 MB graphic card
> does not display correctly in plain VGA mode. The same
> card has no problem with the 2.6.10 kernel.
> Regarding radeonfb, dmesg reports:
> "radeonfb_pci_register BEGIN
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
> low) -> IRQ 169
> radeonfb (0000:01:00.0): Found 131072k of DDR 64 bits
> wide videoram
> radeonfb (0000:01:00.0): mapped 16384k videoram
> radeonfb: Found Intel x86 BIOS ROM Image
> radeonfb: Retreived PLL infos from BIOS
> radeonfb: Reference=27.00 MHz (RefDiv=12)
> Memory=200.00 Mhz, System=166.00 MHz
> radeonfb: PLL min 20000 max 40000
> 1 chips in connector info
> - chip 1 has 1 connectors
> * connector 0 of type 2 (CRT) : 2300
> Starting monitor auto detection...
> radeonfb: I2C (port 1) ... not found
> radeonfb: I2C (port 2) ... not found
> radeonfb: I2C (port 3) ... found CRT display
> radeonfb: I2C (port 4) ... not found
> radeonfb: I2C (port 2) ... not found
> radeonfb: I2C (port 4) ... not found
> radeonfb: I2C (port 3) ... found CRT display
> radeonfb: Monitor 1 type CRT found
> radeonfb: EDID probed
> radeonfb: Monitor 2 type no found
> hStart = 737, hEnd = 808, hTotal = 896
> vStart = 401, vEnd = 404, vTotal = 417
> h_total_disp = 0x59006f hsync_strt_wid = 0x8802eb
> v_total_disp = 0x18f01a0 vsync_strt_wid =
> 0x830190
> pixclock = 38210
> freq = 2617
> freq = 2617, PLL min = 20000, PLL max = 40000
> ref_div = 12, ref_clk = 2700, output_freq = 20936
> ref_div = 12, ref_clk = 2700, output_freq = 20936
> post div = 0x3
> fb_div = 0x5d
> ppll_div_3 = 0x3005d
> Console: switching to colour frame buffer device 90x25
> radeonfb (0000:01:00.0): ATI Radeon Yd
> radeonfb_pci_register END
> kobject_register failed for radeonfb (-17)
> [<c01cf0c7>] kobject_register+0x57/0x60
> [<c0262707>] bus_add_driver+0x57/0xd0
> [<c0262d5f>] driver_register+0x2f/0x40
> [<c01db547>] pci_create_newid_file+0x27/0x30
> [<c01dba42>] pci_register_driver+0x62/0x80
> [<c05b3b40>] radeonfb_old_init+0x40/0x50
> [<c059c7fb>] do_initcalls+0x2b/0xc0
> [<c01002c0>] init+0x0/0x110
> [<c01002c0>] init+0x0/0x110
> [<c01002ef>] init+0x2f/0x110
> [<c010086c>] kernel_thread_helper+0x0/0x14
> [<c0100871>] kernel_thread_helper+0x5/0x14
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Linux agpgart interface v0.100 (c) Dave Jones
> [drm] Initialized drm 1.0.0 20040925
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
> low) -> IRQ 169
> [drm] Initialized radeon 1.14.0 20050125 on minor 0:
> ATI Technologies Inc RV280[Radeon 9200 SE]"
>
It looks like you have no agpgart chipset driver loaded or if DRM is
in the kernel, the agpgart chipset driver should be to...
Dave.
next prev parent reply other threads:[~2005-03-07 23:22 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-03-06 17:49 PROBLEM: Radeon card displays incorrectly under the 2.6.11 version unless compiled with SMP support Lobiuc Andrei
2005-03-07 22:38 ` Dave Airlie [this message]
-- strict thread matches above, loose matches on Subject: below --
2005-03-08 11:59 Lobiuc Andrei
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=21d7e997050307143832a8239c@mail.gmail.com \
--to=airlied@gmail.com \
--cc=alobiuc@yahoo.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox