[PATCH v5 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

Yong Deng
2018-01-11T03:04:56Z

Add binding documentation for Allwinner V3s CSI.

Signed-off-by: Yong Deng <yong.deng@magewell.com>
---
.../devicetree/bindings/media/sun6i-csi.txt | 59 ++++++++++++++++++++++
1 file changed, 59 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt

diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
new file mode 100644
index 0000000..2ff47a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
@@ -0,0 +1,59 @@
+Allwinner V3s Camera Sensor Interface
+-------------------------------------
+
+Allwinner V3s SoC features two CSI module. CSI0 is used for MIPI CSI-2
+interface and CSI1 is used for parallel interface.
+
+Required properties:
+ - compatible: value must be "allwinner,sun8i-v3s-csi"
+ - reg: base address and size of the memory-mapped region.
+ - interrupts: interrupt associated to this IP
+ - clocks: phandles to the clocks feeding the CSI
+ * bus: the CSI interface clock
+ * mod: the CSI module clock
+ * ram: the CSI DRAM clock
+ - clock-names: the clock names mentioned above
+ - resets: phandles to the reset line driving the CSI
+
+Each CSI node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. As mentioned
+above, the endpoint's bus type should be MIPI CSI-2 for CSI0 and parallel or
+Bt656 for CSI1.
+
+Endpoint node properties for CSI1
+---------------------------------
+
+- remote-endpoint : (required) a phandle to the bus receiver's endpoint
+ node
+- bus-width: : (required) must be 8, 10, 12 or 16
+- pclk-sample : (optional) (default: sample on falling edge)
+- hsync-active : (only required for parallel)
+- vsync-active : (only required for parallel)
+
+Example:
+
+csi1: csi@1cb4000 {
+ compatible = "allwinner,sun8i-v3s-csi";
+ reg = <0x01cb4000 0x1000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CSI>,
+ <&ccu CLK_CSI1_SCLK>,
+ <&ccu CLK_DRAM_CSI>;
+ clock-names = "bus", "mod", "ram";
+ resets = <&ccu RST_BUS_CSI>;
+
+ port {
+ /* Parallel bus endpoint */
+ csi1_ep: endpoint {
+ remote-endpoint = <&adv7611_ep>;
+ bus-width = <16>;
+
+ /* If hsync-active/vsync-active are missing,
+ embedded BT.656 sync is used */
+ hsync-active = <0>; /* Active low */
+ vsync-active = <0>; /* Active low */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+};
--
1.8.3.1