From: thomas.mey3r@arcor.de
To: vda@ilport.com.ua
Cc: linux-kernel@vger.kernel.org
Subject: Aw: Re: 2.6.14-rc2-ge484585e: kexec into same kernel: irq 11 nobody cared; but ehci_hcd should
Date: Sat, 24 Sep 2005 16:12:37 +0200 (CEST) [thread overview]
Message-ID: <23431147.1127571157771.JavaMail.ngmail@webmail-05.arcor-online.net> (raw)
In-Reply-To: <200509241530.42284.vda@ilport.com.ua>
Correct.
The interrupt happens before the interrupt is enabled by the ehci driver. the question is why is the interrupt already enabled? or: who forgot to disable the interrupt?
See:
[17179591.828000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[17179591.828000] PCI: setting IRQ 11 as level-triggered
[17179591.828000] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[17179591.828000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[17179591.840000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[17179592.648000] irq 11: nobody cared (try booting with the "irqpoll" option)
[17179592.648000] [<c0103f9e>] dump_stack+0x1e/0x20
[17179592.648000] [<c013dc9b>] __report_bad_irq+0x2b/0x90
[17179592.648000] [<c013ddc0>] note_interrupt+0x90/0xf0
[17179592.648000] [<c013d6ca>] __do_IRQ+0xca/0xe0
[17179592.648000] [<c010530c>] do_IRQ+0x1c/0x30
[17179592.648000] [<c0103b26>] common_interrupt+0x1a/0x20
[17179592.648000] [<c0120ffa>] do_softirq+0x2a/0x30
[17179592.648000] [<c01210a5>] irq_exit+0x35/0x40
[17179592.648000] [<c0105311>] do_IRQ+0x21/0x30
[17179592.648000] [<c0103b26>] common_interrupt+0x1a/0x20
[17179592.648000] [<c013d961>] setup_irq+0xb1/0x110
[17179592.648000] [<c013db16>] request_irq+0x86/0xb0
[17179592.648000] [<ec99c344>] usb_add_hcd+0x234/0x3a0 [usbcore]
[17179592.648000] [<ec9a3a59>] usb_hcd_pci_probe+0x269/0x390 [usbcore]
[17179592.648000] [<c01da2c9>] pci_call_probe+0x19/0x20
[17179592.648000] [<c01da327>] __pci_device_probe+0x57/0x70
[17179592.648000] [<c01da36f>] pci_device_probe+0x2f/0x60
[17179592.648000] [<c021fad9>] driver_probe_device+0x39/0xc0
[17179592.648000] [<c021fc3f>] __driver_attach+0x4f/0x60
[17179592.648000] [<c021f014>] bus_for_each_dev+0x54/0x80
[17179592.648000] [<c021fc78>] driver_attach+0x28/0x30
[17179592.648000] [<c021f52d>] bus_add_driver+0x7d/0xe0
[17179592.648000] [<c0220128>] driver_register+0x78/0x80
[17179592.648000] [<c01da660>] pci_register_driver+0xb0/0xd0
[17179592.648000] [<eca3d020>] init+0x20/0x26 [ehci_hcd]
[17179592.648000] [<c0137e54>] sys_init_module+0x144/0x1c0
[17179592.648000] [<c01030ff>] sysenter_past_esp+0x54/0x75
[17179592.648000] handlers:
[17179592.648000] [<ec99bf20>] (usb_hcd_irq+0x0/0x70 [usbcore])
[17179592.648000] Disabling IRQ #11
[17179592.648000] ehci_hcd 0000:00:10.3: irq 11, io mem 0xd0004800
[17179592.648000] ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[17179592.648000] setting ehci->regs->intr_enable to 37
[17179592.652000] hub 4-0:1.0: USB hub found
[17179592.652000] hub 4-0:1.0: 6 ports detected
----- Original Nachricht ----
Von: Denis Vlasenko <vda@ilport.com.ua>
An: thomas.mey3r@arcor.de
Datum: 24.09.2005 14:30
Betreff: Re: 2.6.14-rc2-ge484585e: kexec into same kernel: irq 11 nobody cared; but ehci_hcd should
> On Saturday 24 September 2005 14:56, thomas.mey3r@arcor.de wrote:
> > Hi.
> >
> > I played a bit with the new kexec function:
> >
> > when i kexec into the same kernel i get this error message:
> >
> > [17179593.108000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
> > [17179593.108000] PCI: setting IRQ 11 as level-triggered
> > [17179593.108000] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] ->
> GSI 11 (level, low) -> IRQ 11
> > [17179593.108000] ehci_hcd 0000:00:10.3: EHCI Host Controller
> > [17179593.124000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned
> bus number 4
> > [17179593.936000] irq 11: nobody cared (try booting with the "irqpoll"
> option)
> > [17179593.936000] [<c0103f9e>] dump_stack+0x1e/0x20
> > [17179593.936000] [<c013dc6b>] __report_bad_irq+0x2b/0x90
> > [17179593.936000] [<c013dd90>] note_interrupt+0x90/0xf0
> > [17179593.936000] [<c013d69a>] __do_IRQ+0xca/0xe0
> > [17179593.936000] [<c010530c>] do_IRQ+0x1c/0x30
> > [17179593.936000] [<c0103b26>] common_interrupt+0x1a/0x20
> > [17179593.936000] [<c0120ffa>] do_softirq+0x2a/0x30
> > [17179593.936000] [<c01210a5>] irq_exit+0x35/0x40
> > [17179593.936000] [<c0105311>] do_IRQ+0x21/0x30
> > [17179593.936000] [<c0103b26>] common_interrupt+0x1a/0x20
> > [17179593.936000] [<c013d931>] setup_irq+0xb1/0x110
> > [17179593.936000] [<c013dae6>] request_irq+0x86/0xb0
> > [17179593.936000] [<ec99c344>] usb_add_hcd+0x234/0x3a0 [usbcore]
> > [17179593.936000] [<ec9a3a59>] usb_hcd_pci_probe+0x269/0x390 [usbcore]
> > [17179593.936000] [<c01da239>] pci_call_probe+0x19/0x20
> > [17179593.936000] [<c01da297>] __pci_device_probe+0x57/0x70
> > [17179593.936000] [<c01da2df>] pci_device_probe+0x2f/0x60
> > [17179593.936000] [<c021fa49>] driver_probe_device+0x39/0xc0
> > [17179593.936000] [<c021fbaf>] __driver_attach+0x4f/0x60
> > [17179593.936000] [<c021ef84>] bus_for_each_dev+0x54/0x80
> > [17179593.936000] [<c021fbe8>] driver_attach+0x28/0x30
> > [17179593.936000] [<c021f49d>] bus_add_driver+0x7d/0xe0
> > [17179593.936000] [<c0220098>] driver_register+0x78/0x80
> > [17179593.936000] [<c01da5d0>] pci_register_driver+0xb0/0xd0
> > [17179593.936000] [<eca3d020>] init+0x20/0x26 [ehci_hcd]
> > [17179593.936000] [<c0137e24>] sys_init_module+0x144/0x1c0
> > [17179593.936000] [<c01030ff>] sysenter_past_esp+0x54/0x75
> > [17179593.936000] handlers:
> > [17179593.936000] [<ec99bf20>] (usb_hcd_irq+0x0/0x70 [usbcore])
> > [17179593.936000] Disabling IRQ #11
> > [17179593.972000] ehci_hcd 0000:00:10.3: irq 11, io mem 0xd0004800
> > [17179593.972000] ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00,
> driver 10 Dec 2004
> > [17179593.976000] hub 4-0:1.0: USB hub found
> > [17179593.976000] hub 4-0:1.0: 6 ports detected
> >
> > CPU0
> > 0: 245067 XT-PIC timer
> > 1: 2877 XT-PIC i8042
> > 2: 0 XT-PIC cascade
> > 4: 37766 XT-PIC uhci_hcd:usb1, eth0,
> via@pci:0000:01:00.0
> > 5: 296 XT-PIC yenta, ohci1394, uhci_hcd:usb2
> > 7: 2 XT-PIC parport0
> > 8: 2 XT-PIC rtc
> > 9: 51497 XT-PIC uhci_hcd:usb3, VIA8233
> > 10: 9 XT-PIC acpi
> > 11: 100000 XT-PIC ehci_hcd:usb4
> > 12: 86427 XT-PIC i8042
> > 14: 10409 XT-PIC ide0
> > 15: 19973 XT-PIC ide1
> > NMI: 0
> > LOC: 0
> > ERR: 0
> > MIS: 0
> >
> > any ideas?
>
> I suspect that interrupt happens before intr mast is written
> ot corresponding register.
>
> Add two printks, one before this writel:
>
> printk("setting ehci->regs->intr_enable to %x\n", INTR_MASK);
> writel (INTR_MASK, &ehci->regs->intr_enable); /* Turn On Interrupts
> */
>
> and one here:
>
> status &= INTR_MASK;
> if (!status) { /* irq sharing? */
> static int ratelimit = 20;
> if(ratelimit) ratelimit--, printk("ehci_irq: IRQ_NONE\n");
> spin_unlock(&ehci->lock);
> return IRQ_NONE;
> }
>
> and see whether first printk happens before second.
> --
> vda
>
next prev parent reply other threads:[~2005-09-24 14:12 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-24 11:56 2.6.14-rc2-ge484585e: kexec into same kernel: irq 11 nobody cared; but ehci_hcd should thomas.mey3r
2005-09-24 12:30 ` Denis Vlasenko
2005-09-24 14:12 ` thomas.mey3r [this message]
2005-09-24 15:07 ` Aw: " Denis Vlasenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=23431147.1127571157771.JavaMail.ngmail@webmail-05.arcor-online.net \
--to=thomas.mey3r@arcor.de \
--cc=linux-kernel@vger.kernel.org \
--cc=vda@ilport.com.ua \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).