From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S268145AbUIRWSf (ORCPT ); Sat, 18 Sep 2004 18:18:35 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S268216AbUIRWSd (ORCPT ); Sat, 18 Sep 2004 18:18:33 -0400 Received: from gw02.mail.saunalahti.fi ([195.197.172.116]:63682 "EHLO gw02.mail.saunalahti.fi") by vger.kernel.org with ESMTP id S268145AbUIRWRj convert rfc822-to-8bit (ORCPT ); Sat, 18 Sep 2004 18:17:39 -0400 Message-ID: <2755554.1095545857871.JavaMail.keripukki@jippii.fi> Date: Sun, 19 Sep 2004 01:17:37 +0300 (EEST) From: keripukki@jippii.fi To: linux-kernel@vger.kernel.org Subject: PROBLEM: Disabling IRQ #11 after couple of hours Mime-Version: 1.0 Content-Type: text/plain; Charset=iso-8859-1; Format=Flowed Content-Transfer-Encoding: 8BIT X-Mailer: Saunalahti webmail - http://www.saunalahti.fi X-Originating-IP: 213.216.233.250 Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org After I use computer for couple of hours, it suddenly starts lagging and I'm getting message 'Disabling IRQ #11'. Then I have to reset computer. I also get these messages: end_request: I/O error, dev hde, sector 126792951 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 ... the message above about 50 times ... end_request: I/O error, dev hde, sector 202904167 EXT3-fs error (device hde1): ext3_readdir: directory #11141435 contains a hole at offset 0 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 end_request: I/O error, dev hde, sector 127164895 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7915824 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126615879 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=7914482, block=15826977 end_request: I/O error, dev hde, sector 126877775 printk: 3 messages suppressed. Buffer I/O error on device hde1, logical block 15859714 lost page write due to I/O error on hde1 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 end_request: I/O error, dev hde, sector 126615655 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=7913586, block=15826949 end_request: I/O error, dev hde, sector 126616255 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=7915970, block=15827024 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126757887 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_readdir: directory #7914705 contains a hole at offset 0 end_request: I/O error, dev hde, sector 126757887 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7914705 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126785535 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7914623 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126757887 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_readdir: directory #7914705 contains a hole at offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 126792951 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7913590 offset 0 end_request: I/O error, dev hde, sector 128328663 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7914710 offset 0 end_request: I/O error, dev hde, sector 126786023 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_find_entry: reading directory #7915963 offset 0 end_request: I/O error, dev hde, sector 126353575 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=7897448, block=15794189 end_request: I/O error, dev hde, sector 126353559 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=7897407, block=15794187 Debug: sleeping function called from invalid context at include/asm/semaphore.h:119 in_atomic():1, irqs_disabled():0 [] __might_sleep+0xb2/0xd3 [] drm_free+0xb7/0x150 [fglrx] [] __ke_down_struct_sem+0x2a/0x44 [fglrx] [] firegl_remove_all_drawables+0x3f/0x100 [fglrx] [] firegl_release_helper+0x546/0x750 [fglrx] [] firegl_takedown+0x32/0xaa0 [fglrx] [] firegl_release+0x12f/0x190 [fglrx] [] sys_fstat64+0x37/0x39 [] __fput+0x112/0x124 [] filp_close+0x59/0x86 [] sys_close+0x63/0x96 [] syscall_call+0x7/0xb end_request: I/O error, dev hde, sector 4287 Buffer I/O error on device hde1, logical block 528 lost page write due to I/O error on hde1 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 ------------ On boot I get this: Linux version 2.6.8-gentoo-r3 (root@mikonkone) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #5 Thu Sep 16 14:40:21 Local time zone must be set--see zic manu BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126960 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.2 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f74b0 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7e00 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 Built 1 zonelists Kernel command line: root=/dev/hda3 Initializing CPU#0 CPU 0 irqstacks, hard=c0498000 soft=c0497000 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2088.265 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 514656k/524224k available (2578k kernel code, 8804k reserved, 935k data, 136k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 4120.57 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(tm) XP 2800+ stepping 00 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Discovered primary peer bus ff [IRQ] PCI: Using IRQ router default [10de/01e0] at 0000:00:00.0 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1095517384.008:0): initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). udf: registering filesystem mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 lp: driver loaded but no devices found Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected NVIDIA nForce2 chipset agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xe0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 [PCSPP(,...)] lp0: using parport0 (polling). Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xa000, 00:04:61:52:9c:0a, IRQ 5 eth0: Identified 8139 chip type 'RTL-8101' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE2: IDE controller at PCI slot 0000:00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA hda: ST330621A, ATA DISK drive hdb: CREATIVEDVD5240E-1, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: HL-DT-ST GCE-8400B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 SiI3112 Serial ATA: IDE controller at PCI slot 0000:01:0c.0 SiI3112 Serial ATA: chipset revision 2 SiI3112 Serial ATA: 100% native mode on irq 11 ide2: MMIO-DMA , BIOS settings: hde:DMA, hdf:DMA ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio hde: Maxtor 6Y120M0, ATA DISK drive ide2 at 0xe0848080-0xe0848087,0xe084808a on irq 11 hdg: no response (status = 0xfe) hdg: no response (status = 0xfe), resetting drive hdg: no response (status = 0xfe) hda: max request size: 128KiB hda: 58633344 sectors (30020 MB) w/512KiB Cache, CHS=58168/16/63, UDMA(100) hda: hda1 hda2 hda3 hde: max request size: 64KiB hde: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63 hde: hde1 irq 11: nobody cared! [] __report_bad_irq+0x2a/0x8b [] note_interrupt+0x6f/0x9f [] do_IRQ+0x17c/0x1a8 [] common_interrupt+0x18/0x20 [] __do_softirq+0x2f/0x80 [] do_softirq+0x43/0x52 ======================= [] do_IRQ+0x155/0x1a8 [] common_interrupt+0x18/0x20 [] default_idle+0x23/0x26 [] cpu_idle+0x2c/0x35 [] start_kernel+0x165/0x17f [] unknown_bootoption+0x0/0x149 handlers: [] (ide_intr+0x0/0x18e) Disabling IRQ #11 hde: lost interrupt irq 11: nobody cared! [] __report_bad_irq+0x2a/0x8b [] note_interrupt+0x6f/0x9f [] do_IRQ+0x17c/0x1a8 [] common_interrupt+0x18/0x20 [] handle_IRQ_event+0x24/0x64 [] do_IRQ+0xcc/0x1a8 ======================= [] task_no_data_intr+0x0/0x95 [] common_interrupt+0x18/0x20 [] task_no_data_intr+0x0/0x95 [] ide_timer_expiry+0x118/0x220 [] ide_timer_expiry+0x0/0x220 [] run_timer_softirq+0xce/0x1ae [] __do_softirq+0x7e/0x80 [] do_softirq+0x43/0x52 ======================= [] do_IRQ+0x155/0x1a8 [] common_interrupt+0x18/0x20 [] default_idle+0x23/0x26 [] cpu_idle+0x2c/0x35 [] start_kernel+0x165/0x17f [] unknown_bootoption+0x0/0x149 handlers: [] (ide_intr+0x0/0x18e) Disabling IRQ #11 hdb: ATAPI 32X DVD-ROM drive, 512kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA libata version 1.02 loaded. ohci1394: $Rev: 1223 $ Ben Collins ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[eb002000-eb0027ff] Max Packet=[2048] ieee1394: raw1394: /dev/raw1394 device initialized ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: irq 5, pci mem e085e000 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: irq 5, pci mem e0860000 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2) PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: irq 11, pci mem e0862000 ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected USB Universal Host Controller Interface driver v2.2 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC). PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 49347 usecs intel8x0: clocking to 47373 ALSA device list: #0: NVidia nForce2 at 0xec001000, irq 5 oprofile: using timer interrupt. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 1 NET: Registered protocol family 17 ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 136k freed Adding 498952k swap on /dev/hda2. Priority:-1 extents:1 hde: sata_error = 0x00090000, watchdog = 1, siimage_mmio_ide_dma_test_irq ieee1394: Host added: ID:BUS[0-00:1023] GUID[0004610000052c50] hde: dma_timer_expiry: dma status == 0x61 hde: DMA timeout error hde: dma timeout error: status=0xd0 { Busy } hde: DMA disabled ide2: reset phy, status=0x00000113, siimage_reset ide2: reset timed-out, status=0xd0 hde: status timeout: status=0xd0 { Busy } ide2: reset phy, status=0x00000113, siimage_reset hde: drive not ready for command irq 11: nobody cared! [] __report_bad_irq+0x2a/0x8b [] note_interrupt+0x6f/0x9f [] do_IRQ+0x17c/0x1a8 [] common_interrupt+0x18/0x20 [] __do_softirq+0x2f/0x80 [] do_softirq+0x43/0x52 ======================= [] do_IRQ+0x155/0x1a8 [] common_interrupt+0x18/0x20 [] default_idle+0x23/0x26 [] cpu_idle+0x2c/0x35 [] start_kernel+0x165/0x17f [] unknown_bootoption+0x0/0x149 handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 ide2: reset phy dead, status=0x00000000 ide2: host reset_poll failure for hde. hde: status timeout: status=0xd0 { Busy } ide2: reset phy, status=0x00000000, siimage_reset ide2: reset phy dead, status=0x00000000 hde: drive not ready for command irq 11: nobody cared! [] __report_bad_irq+0x2a/0x8b [] note_interrupt+0x6f/0x9f [] do_IRQ+0x17c/0x1a8 [] reset_pollfunc+0x0/0x1b9 [] common_interrupt+0x18/0x20 [] reset_pollfunc+0x0/0x1b9 [] ide_timer_expiry+0x118/0x220 [] ide_timer_expiry+0x0/0x220 [] run_timer_softirq+0xce/0x1ae [] __do_softirq+0x7e/0x80 [] do_softirq+0x43/0x52 ======================= [] do_IRQ+0x155/0x1a8 [] common_interrupt+0x18/0x20 [] default_idle+0x23/0x26 [] cpu_idle+0x2c/0x35 [] start_kernel+0x165/0x17f [] unknown_bootoption+0x0/0x149 handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 ide2: reset phy dead, status=0x00000000 ide2: host reset_poll failure for hde. end_request: I/O error, dev hde, sector 65 irq 11: nobody cared! [] __report_bad_irq+0x2a/0x8b [] note_interrupt+0x6f/0x9f [] do_IRQ+0x17c/0x1a8 [] reset_pollfunc+0x0/0x1b9 [] common_interrupt+0x18/0x20 [] reset_pollfunc+0x0/0x1b9 [] ide_timer_expiry+0x118/0x220 [] ide_timer_expiry+0x0/0x220 [] run_timer_softirq+0xce/0x1ae [] __do_softirq+0x7e/0x80 [] do_softirq+0x43/0x52 ======================= [] do_IRQ+0x155/0x1a8 [] common_interrupt+0x18/0x20 [] default_idle+0x23/0x26 [] cpu_idle+0x2c/0x35 [] start_kernel+0x165/0x17f [] unknown_bootoption+0x0/0x149 handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 EXT3-fs: unable to read superblock irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 irq 11: nobody cared! Stack pointer is garbage, not printing trace handlers: [] (ide_intr+0x0/0x18e) [] (ohci_irq_handler+0x0/0x80e) [] (usb_hcd_irq+0x0/0x67) Disabling IRQ #11 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 vmmon: module license 'unspecified' taints kernel. /dev/vmmon: Module vmmon: registered with major=10 minor=165 /dev/vmmon: Module vmmon: initialized /dev/vmnet: open called by PID 6727 (vmnet-bridge) /dev/vmnet: hub 0 does not exist, allocating memory. /dev/vmnet: port on hub 0 successfully opened bridge-eth0: enabling the bridge bridge-eth0: up bridge-eth0: already up bridge-eth0: attached /dev/vmnet: open called by PID 6738 (vmnet-natd) /dev/vmnet: hub 8 does not exist, allocating memory. /dev/vmnet: port on hub 8 successfully opened /dev/vmnet: open called by PID 6897 (vmnet-netifup) /dev/vmnet: port on hub 8 successfully opened /dev/vmnet: open called by PID 6918 (vmnet-dhcpd) /dev/vmnet: port on hub 8 successfully opened --- Kernel version is 2.6.8-gentoo. I can't give better from /proc/version because I'm running with different (2.4) kernel now. I have EPOX 8RDA3+ and I have tested using kernel without usb and acpi (which I thought would cause problem) but I still got same errors. lspci -vvv 0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- Reset- FastB2B- 0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: Unknown device 1695:1000 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- TAbort- SERR- Reset- FastB2B- 0000:01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Unknown device 1695:9001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- [disabled] [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:01:0c.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3112 SATARaid Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 0000:01:0d.0 FireWire (IEEE 1394): Agere Systems (former Lucent Microelectronics) FW323 (rev 61) (prog-if 10 [OHCI]) Subsystem: Unknown device 1695:9015 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- [disabled] [size=128K] Capabilities: [58] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate= Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:02:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary) Subsystem: C.P. Technology Co. Ltd PowerColor R96A-C3N (Secondary) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-