From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: John Stultz <john.stultz@linaro.org>
Cc: lkml <linux-kernel@vger.kernel.org>,
David Airlie <airlied@linux.ie>,
Archit Taneja <architt@codeaurora.org>,
Wolfram Sang <wsa+renesas@sang-engineering.com>,
Lars-Peter Clausen <lars@metafoo.de>,
dri-devel@lists.freedesktop.org
Subject: Re: [PATCH 4/5 v3] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
Date: Mon, 16 Jan 2017 17:50:20 +0200 [thread overview]
Message-ID: <3051780.qdkxg3Jpn9@avalon> (raw)
In-Reply-To: <1483472502-16403-5-git-send-email-john.stultz@linaro.org>
Hi John,
Thank you for the patch.
On Tuesday 03 Jan 2017 11:41:41 John Stultz wrote:
> In chasing down issues with EDID probing, I found some
> duplicated but incomplete logic used to power the chip on and
> off.
>
> This patch refactors the adv7511_power_on/off functions, so
> they can be used for internal needs.
>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Archit Taneja <architt@codeaurora.org>
> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Cc: Lars-Peter Clausen <lars@metafoo.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: John Stultz <john.stultz@linaro.org>
> ---
> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 14 ++++++++++----
> 1 file changed, 10 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c index 4b90975..dbdb71c
> 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> @@ -325,7 +325,7 @@ static void adv7511_set_link_config(struct adv7511
> *adv7511, adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
> }
>
> -static void adv7511_power_on(struct adv7511 *adv7511)
> +static void __adv7511_power_on(struct adv7511 *adv7511)
> {
> adv7511->current_edid_segment = -1;
>
> @@ -359,24 +359,30 @@ static void adv7511_power_on(struct adv7511 *adv7511)
> * Most of the registers are reset during power down or when HPD is
low.
> */
> regcache_sync(adv7511->regmap);
> +}
>
> +static void adv7511_power_on(struct adv7511 *adv7511)
> +{
> + __adv7511_power_on(adv7511);
> if (adv7511->type == ADV7533)
> adv7533_dsi_power_on(adv7511);
> -
> adv7511->powered = true;
> }
>
> -static void adv7511_power_off(struct adv7511 *adv7511)
> +static void __adv7511_power_off(struct adv7511 *adv7511)
> {
> /* TODO: setup additional power down modes */
> regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
> ADV7511_POWER_POWER_DOWN,
> ADV7511_POWER_POWER_DOWN);
> regcache_mark_dirty(adv7511->regmap);
> +}
>
> +static void adv7511_power_off(struct adv7511 *adv7511)
> +{
> + __adv7511_power_off(adv7511);
> if (adv7511->type == ADV7533)
> adv7533_dsi_power_off(adv7511);
> -
> adv7511->powered = false;
> }
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2017-01-16 15:50 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-03 19:41 [PATCH 0/5 v3] adv7511 EDID probing improvements John Stultz
2017-01-03 19:41 ` [PATCH 1/5 v3] drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context John Stultz
2017-01-03 19:41 ` [PATCH 2/5 v3] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event() John Stultz
2017-01-16 15:47 ` Laurent Pinchart
2017-01-16 15:56 ` Laurent Pinchart
2017-01-16 19:31 ` John Stultz
2017-01-03 19:41 ` [PATCH 3/5 v3] drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection John Stultz
2017-01-03 19:41 ` [PATCH 4/5 v3] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally John Stultz
2017-01-16 15:50 ` Laurent Pinchart [this message]
2017-01-03 19:41 ` [PATCH 5/5 v3] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID John Stultz
2017-01-16 16:03 ` Laurent Pinchart
2017-01-16 20:14 ` John Stultz
2017-01-16 22:25 ` Laurent Pinchart
2017-01-16 23:16 ` [RFC][PATCH] drm/bridge: adv7511: Re-write the i2c address as it may have been lost John Stultz
2017-01-16 23:36 ` Laurent Pinchart
2017-01-16 23:39 ` John Stultz
2017-01-11 8:48 ` [PATCH 0/5 v3] adv7511 EDID probing improvements Archit Taneja
2017-01-12 0:06 ` John Stultz
2017-01-12 4:22 ` Archit Taneja
2017-01-16 15:57 ` Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3051780.qdkxg3Jpn9@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=airlied@linux.ie \
--cc=architt@codeaurora.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=john.stultz@linaro.org \
--cc=lars@metafoo.de \
--cc=linux-kernel@vger.kernel.org \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox