From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Josh Wu <josh.wu@atmel.com>
Cc: Linux Media Mailing List <linux-media@vger.kernel.org>,
Guennadi Liakhovetski <g.liakhovetski@gmx.de>,
Mauro Carvalho Chehab <mchehab@osg.samsung.com>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 3/3] media: atmel-isi: add sanity check for supported formats in try/set_fmt()
Date: Fri, 21 Aug 2015 21:22:43 +0300 [thread overview]
Message-ID: <30646920.vM5hNRm83J@avalon> (raw)
In-Reply-To: <1440144494-11800-3-git-send-email-josh.wu@atmel.com>
Hi Josh,
Thank you for the patch.
On Friday 21 August 2015 16:08:14 Josh Wu wrote:
> After adding the format check in try_fmt()/set_fmt(), we don't need any
> format check in configure_geometry(). So make configure_geometry() as
> void type.
>
> Signed-off-by: Josh Wu <josh.wu@atmel.com>
> ---
>
> Changes in v3:
> - check the whether format is supported, if no then return a default
> format.
> - misc changes according to Laurent's feedback.
>
> Changes in v2:
> - new added patch
>
> drivers/media/platform/soc_camera/atmel-isi.c | 37 ++++++++++++++++++------
> 1 file changed, 29 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/media/platform/soc_camera/atmel-isi.c
> b/drivers/media/platform/soc_camera/atmel-isi.c index fe9247a..84c91d3
> 100644
> --- a/drivers/media/platform/soc_camera/atmel-isi.c
> +++ b/drivers/media/platform/soc_camera/atmel-isi.c
> @@ -102,17 +102,19 @@ static u32 isi_readl(struct atmel_isi *isi, u32 reg)
> return readl(isi->regs + reg);
> }
>
> -static int configure_geometry(struct atmel_isi *isi, u32 width,
> +static void configure_geometry(struct atmel_isi *isi, u32 width,
> u32 height, u32 code)
> {
> u32 cfg2;
>
> /* According to sensor's output format to set cfg2 */
> switch (code) {
> - /* YUV, including grey */
> + default:
> + /* Grey */
> case MEDIA_BUS_FMT_Y8_1X8:
> cfg2 = ISI_CFG2_GRAYSCALE;
> break;
> + /* YUV */
> case MEDIA_BUS_FMT_VYUY8_2X8:
> cfg2 = ISI_CFG2_YCC_SWAP_MODE_3;
> break;
> @@ -126,8 +128,6 @@ static int configure_geometry(struct atmel_isi *isi, u32
> width, cfg2 = ISI_CFG2_YCC_SWAP_DEFAULT;
> break;
> /* RGB, TODO */
> - default:
> - return -EINVAL;
> }
>
> isi_writel(isi, ISI_CTRL, ISI_CTRL_DIS);
> @@ -138,8 +138,23 @@ static int configure_geometry(struct atmel_isi *isi,
> u32 width, cfg2 |= ((height - 1) << ISI_CFG2_IM_VSIZE_OFFSET)
> & ISI_CFG2_IM_VSIZE_MASK;
> isi_writel(isi, ISI_CFG2, cfg2);
> +}
>
> - return 0;
> +static bool is_supported(struct soc_camera_device *icd,
> + const u32 pixformat)
> +{
> + switch (pixformat) {
> + /* YUV, including grey */
> + case V4L2_PIX_FMT_GREY:
> + case V4L2_PIX_FMT_YUYV:
> + case V4L2_PIX_FMT_UYVY:
> + case V4L2_PIX_FMT_YVYU:
> + case V4L2_PIX_FMT_VYUY:
> + return true;
> + /* RGB, TODO */
> + default:
> + return false;
> + }
> }
>
> static irqreturn_t atmel_isi_handle_streaming(struct atmel_isi *isi)
> @@ -390,10 +405,8 @@ static int start_streaming(struct vb2_queue *vq,
> unsigned int count) /* Disable all interrupts */
> isi_writel(isi, ISI_INTDIS, (u32)~0UL);
>
> - ret = configure_geometry(isi, icd->user_width, icd->user_height,
> + configure_geometry(isi, icd->user_width, icd->user_height,
> icd->current_fmt->code);
> - if (ret < 0)
> - return ret;
>
> spin_lock_irq(&isi->lock);
> /* Clear any pending interrupt */
> @@ -491,6 +504,10 @@ static int isi_camera_set_fmt(struct soc_camera_device
> *icd, struct v4l2_mbus_framefmt *mf = &format.format;
> int ret;
>
> + /* check with atmel-isi support format, if not support use UYVY */
> + if (!is_supported(icd, pix->pixelformat))
> + pix->pixelformat = V4L2_PIX_FMT_YUYV;
The comment mentions UYVY and the code uses YUYV.
> +
> xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat);
> if (!xlate) {
> dev_warn(icd->parent, "Format %x not found\n",
Can this still happen ?
> @@ -540,6 +557,10 @@ static int isi_camera_try_fmt(struct soc_camera_device
> *icd, u32 pixfmt = pix->pixelformat;
> int ret;
>
> + /* check with atmel-isi support format, if not support use UYVY */
> + if (!is_supported(icd, pix->pixelformat))
> + pix->pixelformat = V4L2_PIX_FMT_YUYV;
> +
> xlate = soc_camera_xlate_by_fourcc(icd, pixfmt);
> if (pixfmt && !xlate) {
> dev_warn(icd->parent, "Format %x not found\n", pixfmt);
Same comment here.
I wonder whether most of the content of isi_camera_set_fmt() and
isi_camera_try_fmt() could be factorized out into a shared function.
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2015-08-21 18:22 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-08-21 8:08 [PATCH v3 1/3] media: atmel-isi: setup the ISI_CFG2 register directly Josh Wu
2015-08-21 8:08 ` [PATCH v3 2/3] media: atmel-isi: move configure_geometry() to start_streaming() Josh Wu
2015-08-21 8:08 ` [PATCH v3 3/3] media: atmel-isi: add sanity check for supported formats in try/set_fmt() Josh Wu
2015-08-21 18:22 ` Laurent Pinchart [this message]
2015-08-24 10:30 ` Josh Wu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=30646920.vM5hNRm83J@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=g.liakhovetski@gmx.de \
--cc=josh.wu@atmel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@osg.samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox