Re: [PATCH V3 0/7] drm: bridge: samsung-dsim: Support variable clocking

[Alexander Stein <alexander.stein@ew.tq-group.com>]

Hi Adam,

Am Dienstag, 2. Mai 2023, 03:07:52 CEST schrieb Adam Ford:
> This series fixes the blanking pack size and the PMS calculation.  It then
> adds support to allows the DSIM to dynamically DPHY clocks, and support
> non-burst mode while allowing the removal of the hard-coded clock values
> for the PLL for imx8m mini/nano/plus, and it allows the removal of the
> burst-clock device tree entry when burst-mode isn't supported by connected
> devices like an HDMI brige.  In that event, the HS clock is set to the value
> requested by the bridge chip.
> 
> This has been tested on both an i.MX8M Nano and i.MX8M Plus, and should work
> on i.MX8M Mini as well.
> 
> Adam Ford (6):
>   drm: bridge: samsung-dsim: Fix PMS Calculator on imx8m[mnp]
>   drm: bridge: samsung-dsim: Fetch pll-clock-frequency automatically
>   drm: bridge: samsung-dsim: Select GENERIC_PHY_MIPI_DPHY
>   drm: bridge: samsung-dsim: Dynamically configure DPHY timing
>   drm: bridge: samsung-dsim: Support non-burst mode
>   drm: bridge: samsung-dsim: Let blanking calcuation work in non-burst
>     mode
> 
> Lucas Stach (1):
>   drm: bridge: samsung-dsim: fix blanking packet size calculation
> 
>  drivers/gpu/drm/bridge/Kconfig        |   1 +
>  drivers/gpu/drm/bridge/samsung-dsim.c | 150 ++++++++++++++++++++++----
>  include/drm/bridge/samsung-dsim.h     |   5 +
>  3 files changed, 136 insertions(+), 20 deletions(-)

Whole series tested on TQMa8MxML/MBa8Mx using a SN65DSI84 + Tianma TM070JVHG33 
display.

Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>

> ---
> V3:  When checking if the bust-clock is present, only check for it
>      in the device tree, and don't check the presence of the
>      MIPI_DSI_MODE_VIDEO_BURST flag as it breaks an existing Exynos
>      board.
> 
>      Add a new patch to the series to select GENERIC_PHY_MIPI_DPHY in
>      Kconfig otherwise the build breaks on the 32-bit Exynos.
> 
>      Change vco_min variable name to min_freq
> 
>      Added tested-by from Chen-Yu Tsai
> 
> V2:  Instead of using my packet blanking calculation, this integrates
>      on from Lucas Stach which gets modified later in the series to
>      cache the value of the HS-clock instead of having to do the
>      calucations again.
> 
>      Instead of completely eliminating the PLL clock frequency from
>      the device tree, this makes it optional to avoid breaking some
>      Samsung devices.  When the samsung,pll-clock-frequency is not
>      found, it reads the value of the clock named "sclk_mipi"
>      This also maintains backwords compatibility with older device
>      trees.
> 
>      This also changes the DPHY calcuation from a Look-up table,
>      a reverse engineered algorithm which uses
>      phy_mipi_dphy_get_default_config to determine the standard
>      nominal values and calculates the cycles necessary to update
>      the DPHY timings accordingly.


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/