From: Miles Lane <miles@speakeasy.org>
To: linux-kernel@vger.kernel.org
Subject: test10-pre5 won't boot on my Athlon machine (Irongate and Viper chip sets)
Date: Thu, 26 Oct 2000 15:19:28 -0700 [thread overview]
Message-ID: <39F8ADF0.5050400@speakeasy.org> (raw)
Perhaps this is related to the PCI issues that are being debated on the list now.
Would someone look at my bus configuration and let me know what to test or what patch to apply to get my kernel booting?
lspci -vv reports:
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller (rev 25)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64 set
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fc9ff000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at ffe4 [disabled] [size=4]
Capabilities: [a0] AGP version 1.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: e4800000-f48fffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-756 [Viper] IDE (rev 03) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at cb00 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ACPI (rev 03)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:07.4 USB Controller: Advanced Micro Devices [AMD] AMD-756 [Viper] USB (rev 06) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 max, 16 set, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
00:0f.0 SCSI storage controller: Adaptec AHA-2930CU (rev 03)
Subsystem: Adaptec: Unknown device 3869
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 4 min, 4 max, 64 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at f800 [size=256]
Region 1: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at febe0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Communication controller: Lucent Microelectronics Venus WinModem (V90, 56KFlex)
Subsystem: Action Tec Electronics Inc: Unknown device 0500
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 252 min, 14 max, 0 set
Interrupt: pin A routed to IRQ 9
Region 0: Memory at febfdf00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at f400 [size=256]
Region 2: I/O ports at f000 [size=256]
Region 3: I/O ports at ffa8 [size=8]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- AuxPwr- DSI+ D1- D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
Subsystem: 3Com Corporation: Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 10 min, 10 max, 64 set, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at fc00 [size=128]
Region 1: Memory at febfde80 (32-bit, non-prefetchable) [size=128]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:14.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs CT4831 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 2 min, 20 max, 64 set
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at ff80 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 0: I/O ports at fff0 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller: nVidia Corporation: Unknown device 0101 (rev 10) (prog-if 00 [VGA])
Subsystem: VISIONTEK: Unknown device 000b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 5 min, 1 max, 64 set
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at feaf0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next reply other threads:[~2000-10-26 22:26 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-10-26 22:19 Miles Lane [this message]
2000-10-26 23:08 ` test10-pre5 won't boot on my Athlon machine (Irongate and Viper chip sets) pierre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=39F8ADF0.5050400@speakeasy.org \
--to=miles@speakeasy.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox