From: Miles Lane <miles@megapathdsl.net>
To: Linux Kernel <linux-kernel@vger.kernel.org>
Subject: test13-pre4-ac2 -- The cardbus/pcmcia sockets no longer work with two devices present at boot time.
Date: Wed, 27 Dec 2000 00:42:14 -0800 [thread overview]
Message-ID: <3A49AB66.1000607@megapathdsl.net> (raw)
When I boot with the following inserted:
Socket 0:
product info: "3Com Corporation", "3CCFE575BT", "LAN Cardbus Card", "001"
manfid: 0x0101, 0x5157
function: 6 (network)
Socket 1:
product info: "PCMCIA ", "56K V.90 Fax Modem (LK) ", "FM560LK "
manfid: 0x0175, 0x0000
function: 2 (serial)
both sockets fail to set up properly and work.
Linux PCMCIA Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Enabling device 00:04.0 (0000 -> 0002)
PCI: Assigned IRQ 11 for device 00:04.0
PCI: Enabling device 00:04.1 (0000 -> 0002)
PCI: Assigned IRQ 11 for device 00:04.1
Intel PCIC probe: not found.
Yenta IRQ list 0698, PCI irq11
Socket status: 30000020
Yenta IRQ list 0698, PCI irq11
Socket status: 30000010
ACPI: System description tables not found
cs: socket c118b000 timed out during reset. Try increasing setup_delay.
cs: socket c118b800 timed out during reset. Try increasing setup_delay.
If I then run "cardctl eject" and then eject and reinsert the two
cards, the cards get set up correctly.
Note that I am not using the PCMCIA drivers. I am using Yenta
and its native development kernel friends. I am using modutils
2.3.22.
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 64 set
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=64M]
00:02.0 VGA compatible controller: Neomagic Corporation NM2160
[MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 16 min, 255 max, 128 set
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fea00000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at fed00000 (32-bit, non-prefetchable) [size=1M]
00:04.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168 set, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:04.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 007e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168 set, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=05, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at fcc0 [disabled] [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
01:00.0 Ethernet controller: 3Com Corporation 3c575 [Megahertz] 10/100
LAN CardBus (rev 01)
Subsystem: 3Com Corporation: Unknown device 5b57
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 10 min, 5 max, 64 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [size=128]
Region 1: Memory at 10800000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 10800080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10400000 [size=128K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next reply other threads:[~2000-12-27 9:14 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-12-27 8:42 Miles Lane [this message]
2000-12-27 14:06 ` test13-pre4-ac2 -- The cardbus/pcmcia sockets no longer work with two devices present at boot time Jens Taprogge
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3A49AB66.1000607@megapathdsl.net \
--to=miles@megapathdsl.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox