* Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2.
@ 2001-01-09 9:12 Silviu Marin-Caea
2001-01-09 10:17 ` Alessandro Suardi
` (3 more replies)
0 siblings, 4 replies; 31+ messages in thread
From: Silviu Marin-Caea @ 2001-01-09 9:12 UTC (permalink / raw)
To: linux-kernel; +Cc: rlug
I have RedHat7, glibc-2.2-9, gcc-2.96-69.
I can build 2.4.0 while running kernel 2.2.16.
If I try to rebuild 2.4.0 while running the new kernel, I get random
compiler errors.
It happens on two machines. One of them runs 2.4.0-test12, the other
2.4.0. Both of them with the updates above mentioned.
I know this is a RedHat issue, but it may be useful to know for some.
--
Systems and Network Administrator - Delta Romania
Phone +4093-267961
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 31+ messages in thread* Re: Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2. 2001-01-09 9:12 Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Silviu Marin-Caea @ 2001-01-09 10:17 ` Alessandro Suardi 2001-01-09 10:33 ` Failure building 2.4 while running 2.4. Success in building 2.4 Alan Cox 2001-01-09 10:28 ` Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Alan Cox ` (2 subsequent siblings) 3 siblings, 1 reply; 31+ messages in thread From: Alessandro Suardi @ 2001-01-09 10:17 UTC (permalink / raw) To: Silviu Marin-Caea; +Cc: linux-kernel, rlug Silviu Marin-Caea wrote: > > I have RedHat7, glibc-2.2-9, gcc-2.96-69. > > I can build 2.4.0 while running kernel 2.2.16. > > If I try to rebuild 2.4.0 while running the new kernel, I get random > compiler errors. > > It happens on two machines. One of them runs 2.4.0-test12, the other > 2.4.0. Both of them with the updates above mentioned. > > I know this is a RedHat issue, but it may be useful to know for some. I know this isn't since I already built 2.4.0-ac2 and -ac3 on this laptop and never got any compiler error :) [asuardi@princess asuardi]$ rpm -q glibc gcc glibc-2.2-9 gcc-2.96-69 random compiler errors => bad hardware. On two machines ? Yes. --alessandro <alessandro.suardi@oracle.com> <asuardi@uninetcom.it> Linux: kernel 2.2.19p6/2.4.0 glibc-2.2 gcc-2.96-69 binutils-2.10.1.0.4 Oracle: Oracle8i 8.1.7.0.0 Enterprise Edition for Linux motto: Tell the truth, there's less to remember. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Failure building 2.4 while running 2.4. Success in building 2.4 2001-01-09 10:17 ` Alessandro Suardi @ 2001-01-09 10:33 ` Alan Cox 2001-01-09 18:20 ` Failure building 2.4 while running 2.4. There is no such thing Silviu Marin-Caea 0 siblings, 1 reply; 31+ messages in thread From: Alan Cox @ 2001-01-09 10:33 UTC (permalink / raw) To: Alessandro Suardi; +Cc: Silviu Marin-Caea, linux-kernel, rlug > I know this isn't since I already built 2.4.0-ac2 and -ac3 on this > laptop and never got any compiler error :) > > [asuardi@princess asuardi]$ rpm -q glibc gcc > glibc-2.2-9 > gcc-2.96-69 > > random compiler errors => bad hardware. On two machines ? Yes. My guess is a bad driver. Two machines with random errors from hardware only in 2.4 is pushing it - possible but pushing it. Alan - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Failure building 2.4 while running 2.4. There is no such thing. 2001-01-09 10:33 ` Failure building 2.4 while running 2.4. Success in building 2.4 Alan Cox @ 2001-01-09 18:20 ` Silviu Marin-Caea 2001-01-09 18:43 ` Alan Cox ` (2 more replies) 0 siblings, 3 replies; 31+ messages in thread From: Silviu Marin-Caea @ 2001-01-09 18:20 UTC (permalink / raw) To: linux-kernel On Tue, 9 Jan 2001 10:33:29 +0000 (GMT) Alan Cox <alan@lxorguk.ukuu.org.uk> wrote: > My guess is a bad driver. Two machines with random errors from hardware only > in 2.4 is pushing it - possible but pushing it. One is bad hardware. The other is bad user. I compiled with DMA support for SiS 5513 and I have SiS 5571. My appologies for the stupid mistake. -- Systems and Network Administrator - Delta Romania Phone +4093-267961 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Failure building 2.4 while running 2.4. There is no such thing. 2001-01-09 18:20 ` Failure building 2.4 while running 2.4. There is no such thing Silviu Marin-Caea @ 2001-01-09 18:43 ` Alan Cox 2001-01-09 19:57 ` Drivers under 2.4 Dennis 2001-01-10 18:22 ` Drivers under 2.4 Dennis 2 siblings, 0 replies; 31+ messages in thread From: Alan Cox @ 2001-01-09 18:43 UTC (permalink / raw) To: Silviu Marin-Caea; +Cc: linux-kernel, andre > One is bad hardware. The other is bad user. I compiled with DMA support > for SiS 5513 and I have SiS 5571. My appologies for the stupid mistake. If the 5513 driver doesnt work on the 5571 it should have ignored it - so thats a driver bug - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Drivers under 2.4 2001-01-09 18:20 ` Failure building 2.4 while running 2.4. There is no such thing Silviu Marin-Caea 2001-01-09 18:43 ` Alan Cox @ 2001-01-09 19:57 ` Dennis 2001-01-09 20:13 ` suser checks in 2.2.x Bosko Radivojevic 2001-01-10 18:22 ` Drivers under 2.4 Dennis 2 siblings, 1 reply; 31+ messages in thread From: Dennis @ 2001-01-09 19:57 UTC (permalink / raw) To: Alan Cox; +Cc: linux-kernel Where might one find the definitive document on porting device drivers to 2.4 kernels? DB - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* suser checks in 2.2.x 2001-01-09 19:57 ` Drivers under 2.4 Dennis @ 2001-01-09 20:13 ` Bosko Radivojevic 2001-01-09 18:39 ` Arnaldo Carvalho de Melo 0 siblings, 1 reply; 31+ messages in thread From: Bosko Radivojevic @ 2001-01-09 20:13 UTC (permalink / raw) To: linux-kernel Hello to all I can see there are a lot of suser() checks. When they will be changed with appropriate capable(..) checks? Or, will they be changed, at all some days? What is going on with VFS capabilities support? Greetings - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: suser checks in 2.2.x 2001-01-09 20:13 ` suser checks in 2.2.x Bosko Radivojevic @ 2001-01-09 18:39 ` Arnaldo Carvalho de Melo 0 siblings, 0 replies; 31+ messages in thread From: Arnaldo Carvalho de Melo @ 2001-01-09 18:39 UTC (permalink / raw) To: Bosko Radivojevic; +Cc: linux-kernel Em Tue, Jan 09, 2001 at 09:13:46PM +0100, Bosko Radivojevic escreveu: > I can see there are a lot of suser() checks. When they will be changed > with appropriate capable(..) checks? Or, will they be changed, at all some > days? I assume: as soon as people send patches, I've send two, IIRC, related to this today. 8) - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-09 18:20 ` Failure building 2.4 while running 2.4. There is no such thing Silviu Marin-Caea 2001-01-09 18:43 ` Alan Cox 2001-01-09 19:57 ` Drivers under 2.4 Dennis @ 2001-01-10 18:22 ` Dennis 2001-01-10 20:01 ` Hans Grobler 2001-01-10 21:37 ` Dennis 2 siblings, 2 replies; 31+ messages in thread From: Dennis @ 2001-01-10 18:22 UTC (permalink / raw) To: linux-kernel At 02:57 PM 01/09/2001, Dennis wrote: >Where might one find the definitive document on porting device drivers to >2.4 kernels? > >DB should I assume that there are none? - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-10 18:22 ` Drivers under 2.4 Dennis @ 2001-01-10 20:01 ` Hans Grobler 2001-01-10 21:37 ` Dennis 1 sibling, 0 replies; 31+ messages in thread From: Hans Grobler @ 2001-01-10 20:01 UTC (permalink / raw) To: Dennis; +Cc: linux-kernel On Wed, 10 Jan 2001, Dennis wrote: > At 02:57 PM 01/09/2001, Dennis wrote: > >Where might one find the definitive document on porting device drivers to > >2.4 kernels? > > should I assume that there are none? I don't think anyone has had the time yet. I'm sure someone will get around to this soon. If you ask specific questions here, the answers may well form the basis for such a document. -- Hans - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-10 18:22 ` Drivers under 2.4 Dennis 2001-01-10 20:01 ` Hans Grobler @ 2001-01-10 21:37 ` Dennis 2001-01-10 21:38 ` Andi Kleen 1 sibling, 1 reply; 31+ messages in thread From: Dennis @ 2001-01-10 21:37 UTC (permalink / raw) To: Hans Grobler; +Cc: linux-kernel At 03:01 PM 01/10/2001, Hans Grobler wrote: >On Wed, 10 Jan 2001, Dennis wrote: > > At 02:57 PM 01/09/2001, Dennis wrote: > > >Where might one find the definitive document on porting device drivers to > > >2.4 kernels? > > > > should I assume that there are none? > >I don't think anyone has had the time yet. I'm sure someone will get >around to this soon. If you ask specific questions here, the answers may >well form the basis for such a document. Aren't you supposed to design the spec BEFORE you implement it? >-- Hans > > >- >To unsubscribe from this list: send the line "unsubscribe linux-kernel" in >the body of a message to majordomo@vger.kernel.org >Please read the FAQ at http://www.tux.org/lkml/ - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-10 21:37 ` Dennis @ 2001-01-10 21:38 ` Andi Kleen 2001-01-10 22:08 ` Hans Grobler 0 siblings, 1 reply; 31+ messages in thread From: Andi Kleen @ 2001-01-10 21:38 UTC (permalink / raw) To: Dennis; +Cc: Hans Grobler, linux-kernel On Wed, Jan 10, 2001 at 04:37:06PM -0500, Dennis wrote: > At 03:01 PM 01/10/2001, Hans Grobler wrote: > >On Wed, 10 Jan 2001, Dennis wrote: > > > At 02:57 PM 01/09/2001, Dennis wrote: > > > >Where might one find the definitive document on porting device drivers to > > > >2.4 kernels? > > > > > > should I assume that there are none? > > > >I don't think anyone has had the time yet. I'm sure someone will get > >around to this soon. If you ask specific questions here, the answers may > >well form the basis for such a document. > > > Aren't you supposed to design the spec BEFORE you implement it? Try http://www.firstfloor.org/~andi/softnet (minor details outdated) -Andi - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-10 21:38 ` Andi Kleen @ 2001-01-10 22:08 ` Hans Grobler 2001-01-11 10:24 ` Danny ter Haar 0 siblings, 1 reply; 31+ messages in thread From: Hans Grobler @ 2001-01-10 22:08 UTC (permalink / raw) To: Dennis; +Cc: linux-kernel On Wed, 10 Jan 2001, Andi Kleen wrote: > On Wed, Jan 10, 2001 at 04:37:06PM -0500, Dennis wrote: > > > > Aren't you supposed to design the spec BEFORE you implement it? > > Try http://www.firstfloor.org/~andi/softnet (minor details outdated) The softnet changes are most likely the primary source of breakage (for network drivers). You should also read the kernel-* docs under Documentation/DocBook (see Documentation/kernel-doc-nano-HOWTO.txt). -- Hans - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-10 22:08 ` Hans Grobler @ 2001-01-11 10:24 ` Danny ter Haar 2001-01-11 10:31 ` Andi Kleen 2001-01-11 12:56 ` Drivers " Alan Cox 0 siblings, 2 replies; 31+ messages in thread From: Danny ter Haar @ 2001-01-11 10:24 UTC (permalink / raw) To: linux-kernel Hans Grobler <grobh@sun.ac.za> wrote: >The softnet changes are most likely the primary source of breakage (for >network drivers). I happen to have a multimedia box from siemens/fujitsu with a cyrix processor, chipset and amd/lance ethernet chipset onboard. It' working fine with 2.2.x but not with 2.4.x kernels with the same driver version of the pcnet32 networkdriver. 2.4.0-ac4 Jan 9 17:09:53 multimedia kernel: Linux version 2.4.0-ac4 (root@ws1) (gcc version 2.95.3 20001229 (prerelease)) #2 Tue Jan 9 16:22:08 CET 2001 Jan 9 17:09:53 multimedia kernel: PCI: Found IRQ 9 for device 00:0f.0 Jan 9 17:09:53 multimedia kernel: eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d Jan 9 17:09:53 multimedia kernel: pcnet32: pcnet32_private lp=c3c80000 lp_dma_addr=0x3c80000 assigned IRQ 9. Jan 9 17:09:53 multimedia kernel: pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de and 2.2.19pre7 Jan 10 20:46:15 multimedia kernel: Linux version 2.2.19pre7 (root@multimedia) (gcc version 2.95.3 20001229 (prerelease)) #2 Wed Jan 10 20:13:57 CET 2001 Jan 10 20:46:15 multimedia kernel: pcnet32.c: PCI bios is present, checking for devices... Jan 10 20:46:15 multimedia kernel: Found PCnet/PCI at 0xfce0, irq 9. Jan 10 20:46:15 multimedia kernel: eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d assigned IRQ 9. Jan 10 20:46:15 multimedia kernel: pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de Version number of the driver is the same but it doesn't work. Any thoughts anyone ? Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 10:24 ` Danny ter Haar @ 2001-01-11 10:31 ` Andi Kleen 2001-01-11 10:58 ` Danny ter Haar 2001-01-11 12:56 ` Drivers " Alan Cox 1 sibling, 1 reply; 31+ messages in thread From: Andi Kleen @ 2001-01-11 10:31 UTC (permalink / raw) To: Danny ter Haar; +Cc: linux-kernel On Thu, Jan 11, 2001 at 10:24:01AM +0000, Danny ter Haar wrote: > Version number of the driver is the same but it doesn't work. > > Any thoughts anyone ? "Doesn't work" isn't a very useful bug report. What happens exactly? Do the RX/TX/error counters increase when you try to send packets? -Andi - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 10:31 ` Andi Kleen @ 2001-01-11 10:58 ` Danny ter Haar 2001-01-11 11:36 ` Andrew Morton 0 siblings, 1 reply; 31+ messages in thread From: Danny ter Haar @ 2001-01-11 10:58 UTC (permalink / raw) To: Andi Kleen; +Cc: linux-kernel According to Andi Kleen: > "Doesn't work" isn't a very useful bug report. What happens exactly? > Do the RX/TX/error counters increase when you try to send packets? no, the counters you see with ifconfig eth0 are set to zero for rx and to 1 for tx. So it's trying to send out data but somehow it doesn't work. Since the driver version is the same (althoud the output is slihtly different which seems odd) i suspect the PCI probing to be folded somewhere. How could i provide people with more info ? Thanks, Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 10:58 ` Danny ter Haar @ 2001-01-11 11:36 ` Andrew Morton 2001-01-11 11:58 ` Danny ter Haar 0 siblings, 1 reply; 31+ messages in thread From: Andrew Morton @ 2001-01-11 11:36 UTC (permalink / raw) To: dth; +Cc: Andi Kleen, linux-kernel Danny ter Haar wrote: > > According to Andi Kleen: > > "Doesn't work" isn't a very useful bug report. What happens exactly? > > Do the RX/TX/error counters increase when you try to send packets? > > no, the counters you see with ifconfig eth0 are set to zero > for rx and to 1 for tx. > > So it's trying to send out data but somehow it doesn't work. > Since the driver version is the same (althoud the output is > slihtly different which seems odd) i suspect the PCI > probing to be folded somewhere. > > How could i provide people with more info ? There's a "reporting problems" section at the end of Documentation/networking/vortex.txt. Should help. Probably the most important thing is inserting the driver module with `debug=7', opening the device, sending some traffic and then sending us the logs. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 11:36 ` Andrew Morton @ 2001-01-11 11:58 ` Danny ter Haar 2001-01-11 14:00 ` Danny ter Haar 0 siblings, 1 reply; 31+ messages in thread From: Danny ter Haar @ 2001-01-11 11:58 UTC (permalink / raw) To: linux-kernel Andrew Morton <andrewm@uow.edu.au> wrote: >There's a "reporting problems" section at the end >of Documentation/networking/vortex.txt. Should help. okidoki, have read it, thanks >Probably the most important thing is inserting the driver >module with `debug=7', opening the device, sending some >traffic and then sending us the logs. pcnet32_probe_pci: found device 0x001022.0x002000 ioaddr=0x00fce0 resource_flags=0x000101 PCI: Found IRQ 9 for device 00:0f.0 PCnet chip version is 0x22625003. eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d pcnet32: pcnet32_private lp=c3bf6000 lp_dma_addr=0x3bf6000 assigned IRQ 9. pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de eth0: pcnet32_open() irq 9 tx/rx rings 0x3bf6200/0x3bf6000 init 0x3bf6300. eth0: pcnet32 open after 5 ticks, init block 0x3bf6300 csr0 01f3. eth0: pcnet32_start_xmit() called, csr0 01f3. this after bootup, static ip adress multimedia:~# ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:00:E2:24:41:1D inet addr:192.168.1.51 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:9 Base address:0xfce0 multimedia:~# ping -c10 192.168.1.1 PING 192.168.1.1 (192.168.1.1): 56 data bytes --- 192.168.1.1 ping statistics --- 10 packets transmitted, 0 packets received, 100% packet loss after this the following messages in dmesg: Jan 11 12:45:49 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. Jan 11 12:46:01 multimedia last message repeated 12 times Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 11:58 ` Danny ter Haar @ 2001-01-11 14:00 ` Danny ter Haar 2001-01-11 14:32 ` Jeff Garzik 0 siblings, 1 reply; 31+ messages in thread From: Danny ter Haar @ 2001-01-11 14:00 UTC (permalink / raw) To: linux-kernel >Jan 11 12:45:49 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. >Jan 11 12:46:01 multimedia last message repeated 12 times hot from the ethernet wire: more info just arrived: NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, status 07f3, resetting. Ring data dump: dirty_tx 0 cur_tx 16 (full) cur_rx 0. 03b2f012 0608 00000040 0310 03b2f812 0608 00000040 0310 03b2e012 0608 00000040 0310 03b2e812 0608 00000040 0310 03b2d012 0608 00000040 0310 03b2d812 0608 00000040 0310 03b2c012 0608 00000040 0310 03b2c812 0608 00000040 0310 03b2b012 0608 00000040 0310 03b2b812 0608 00000040 0310 03b2a012 0608 00000040 0310 03b2a812 0608 00000040 0310 03b29012 0608 00000040 0310 03b29812 0608 00000040 0310 03b28012 0608 00000040 0310 03b28812 0608 00000111 0310 03b3f012 0608 000000fc 0310 03b3f812 0608 0000006a 0310 03b3e012 0608 00000040 0310 03b3e812 0608 00000040 0310 03b3d012 0608 00000040 0310 03b3d812 0608 00000040 0310 03b3c012 0608 00000040 0310 03b3c812 0608 00000040 0310 03b3a012 0608 00000040 0310 03b3a812 0608 00000040 0310 03b39012 0608 00000040 0310 03b39812 0608 00000040 0340 03b38012 0608 00000040 0340 03b38812 0608 00000040 0340 03b4f012 0608 00000040 0340 03b4f812 0608 00000040 0340 03f9a782 0066 00000000 0300 03b4e222 002a 00000000 0300 03b4e2a2 002a 00000000 0300 03b4e322 002a 00000000 0300 03b4e3a2 002a 00000000 0300 03b4e422 002a 00000000 0300 03b4e4a2 002a 00000000 0300 03b4e522 002a 00000000 0300 03b4e5a2 002a 00000000 0300 03b4e622 002a 00000000 0300 03b4e6a2 002a 00000000 0300 03b4eea2 002a 00000000 0300 03b4ef22 002a 00000000 0300 03f9a882 007e 00000000 0300 03f9a982 007e 00000000 0300 03f9aa82 007e 00000000 0300 eth0: pcnet32_start_xmit() called, csr0 05f3. eth0: pcnet32_start_xmit() called, csr0 07f3. etc... Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 14:00 ` Danny ter Haar @ 2001-01-11 14:32 ` Jeff Garzik 2001-01-11 16:33 ` Danny ter Haar 0 siblings, 1 reply; 31+ messages in thread From: Jeff Garzik @ 2001-01-11 14:32 UTC (permalink / raw) To: dth; +Cc: linux-kernel, Alan Cox [-- Attachment #1: Type: text/plain, Size: 2162 bytes --] Danny ter Haar wrote: > > >Jan 11 12:45:49 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. > >Jan 11 12:46:01 multimedia last message repeated 12 times > > hot from the ethernet wire: more info just arrived: > > NETDEV WATCHDOG: eth0: transmit timed out > eth0: transmit timed out, status 07f3, resetting. > Ring data dump: dirty_tx 0 cur_tx 16 (full) cur_rx 0. > 03b2f012 0608 00000040 0310 03b2f812 0608 00000040 0310 > 03b2e012 0608 00000040 0310 03b2e812 0608 00000040 0310 > 03b2d012 0608 00000040 0310 03b2d812 0608 00000040 0310 > 03b2c012 0608 00000040 0310 03b2c812 0608 00000040 0310 > 03b2b012 0608 00000040 0310 03b2b812 0608 00000040 0310 > 03b2a012 0608 00000040 0310 03b2a812 0608 00000040 0310 > 03b29012 0608 00000040 0310 03b29812 0608 00000040 0310 > 03b28012 0608 00000040 0310 03b28812 0608 00000111 0310 > 03b3f012 0608 000000fc 0310 03b3f812 0608 0000006a 0310 > 03b3e012 0608 00000040 0310 03b3e812 0608 00000040 0310 > 03b3d012 0608 00000040 0310 03b3d812 0608 00000040 0310 > 03b3c012 0608 00000040 0310 03b3c812 0608 00000040 0310 > 03b3a012 0608 00000040 0310 03b3a812 0608 00000040 0310 > 03b39012 0608 00000040 0310 03b39812 0608 00000040 0340 > 03b38012 0608 00000040 0340 03b38812 0608 00000040 0340 > 03b4f012 0608 00000040 0340 03b4f812 0608 00000040 0340 > 03f9a782 0066 00000000 0300 03b4e222 002a 00000000 0300 > 03b4e2a2 002a 00000000 0300 03b4e322 002a 00000000 0300 > 03b4e3a2 002a 00000000 0300 03b4e422 002a 00000000 0300 > 03b4e4a2 002a 00000000 0300 03b4e522 002a 00000000 0300 > 03b4e5a2 002a 00000000 0300 03b4e622 002a 00000000 0300 > 03b4e6a2 002a 00000000 0300 03b4eea2 002a 00000000 0300 > 03b4ef22 002a 00000000 0300 03f9a882 007e 00000000 0300 > 03f9a982 007e 00000000 0300 03f9aa82 007e 00000000 0300 > eth0: pcnet32_start_xmit() called, csr0 05f3. > eth0: pcnet32_start_xmit() called, csr0 07f3. > > etc... Does this patch help at all? Jeff -- Jeff Garzik | "You see, in this world there's two kinds of Building 1024 | people, my friend: Those with loaded guns MandrakeSoft | and those who dig. You dig." --Blondie [-- Attachment #2: pcnet32.patch --] [-- Type: text/plain, Size: 41486 bytes --] Index: drivers/net/pcnet32.c =================================================================== RCS file: /cvsroot/gkernel/linux_2_4/drivers/net/pcnet32.c,v retrieving revision 1.1.1.7 retrieving revision 1.1.1.7.10.1 diff -u -r1.1.1.7 -r1.1.1.7.10.1 --- drivers/net/pcnet32.c 2000/12/12 03:23:16 1.1.1.7 +++ drivers/net/pcnet32.c 2001/01/11 13:38:07 1.1.1.7.10.1 @@ -1,19 +1,22 @@ /* pcnet32.c: An AMD PCnet32 ethernet driver for linux. */ /* * Copyright 1996-1999 Thomas Bogendoerfer - * + * * Derived from the lance driver written 1993,1994,1995 by Donald Becker. - * + * * Copyright 1993 United States Government as represented by the * Director, National Security Agency. - * + * * This software may be used and distributed according to the terms * of the GNU Public License, incorporated herein by reference. * * This driver is for PCnet32 and PCnetPCI based ethercards + * + * Nov 2000 (jgarzik): SMP, endian, PCI DMA, other fixes. + * Removed VLB support (use CONFIG_LANCE instead). */ -static const char *version = "pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de\n"; +static const char *version = "pcnet32.c:v1.25smp Nov 11, 2000 tsbogend@alpha.franken.de\n"; #include <linux/module.h> @@ -37,13 +40,9 @@ #include <linux/skbuff.h> #include <linux/spinlock.h> -static unsigned int pcnet32_portlist[] __initdata = {0x300, 0x320, 0x340, 0x360, 0}; - static int pcnet32_debug = 1; static int tx_start = 1; /* Mapping -- 0:20, 1:64, 2:128, 3:~220 (depends on chip vers) */ -static struct net_device *pcnet32_dev; - static const int max_interrupt_work = 80; static const int rx_copybreak = 200; @@ -63,10 +62,10 @@ * table to translate option values from tulip * to internal options */ -static unsigned char options_mapping[] = { +static unsigned char options_mapping[] __initdata = { PORT_ASEL, /* 0 Auto-select */ PORT_AUI, /* 1 BNC/AUI */ - PORT_AUI, /* 2 AUI/BNC */ + PORT_AUI, /* 2 AUI/BNC */ PORT_ASEL, /* 3 not supported */ PORT_10BT | PORT_FD, /* 4 10baseT-FD */ PORT_ASEL, /* 5 not supported */ @@ -88,14 +87,14 @@ /* * Theory of Operation - * + * * This driver uses the same software structure as the normal lance * driver. So look for a verbose description in lance.c. The differences * to the normal lance driver is the use of the 32bit mode of PCnet32 * and PCnetPCI chips. Because these chips are 32bit chips, there is no * 16MB limitation and we don't need bounce buffers. */ - + /* * History: * v0.01: Initial version @@ -149,7 +148,7 @@ * v1.22: changed pci scanning code to make PPC people happy * fixed switching to 32bit mode in pcnet32_open() (thanks * to Michael Richard <mcr@solidum.com> for noticing this one) - * added sub vendor/device id matching (thanks again to + * added sub vendor/device id matching (thanks again to * Michael Richard <mcr@solidum.com>) * added chip id for 79c973/975 (thanks to Zach Brown <zab@zabbo.net>) * v1.23 fixed small bug, when manual selecting MII speed/duplex @@ -206,6 +205,10 @@ #define PCI_DEVICE_ID_AMD_PCNETHOME 0x2001 #endif +#define DMA_ALLOC_SIZE \ + ( (sizeof(struct pcnet32_rx_head) * RX_RING_SIZE) + \ + (sizeof(struct pcnet32_tx_head) * TX_RING_SIZE) + \ + sizeof(struct pcnet32_init_block) ) #define CRC_POLYNOMIAL_LE 0xedb88320UL /* Ethernet CRC, little endian */ @@ -213,11 +216,11 @@ struct pcnet32_rx_head { u32 base; s16 buf_length; - s16 status; + s16 status; u32 msg_length; u32 reserved; }; - + struct pcnet32_tx_head { u32 base; s16 length; @@ -233,7 +236,7 @@ u8 phys_addr[6]; u16 reserved; u32 filter[2]; - /* Receive and transmit ring base, along with extra bits. */ + /* Receive and transmit ring base, along with extra bits. */ u32 rx_ring; u32 tx_ring; }; @@ -250,15 +253,18 @@ }; /* - * The first three fields of pcnet32_private are read by the ethernet device + * The first three fields of pcnet32_private are read by the ethernet device * so we allocate the structure should be allocated by pci_alloc_consistent(). */ struct pcnet32_private { /* The Tx and Rx ring entries must be aligned on 16-byte boundaries in 32bit mode. */ - struct pcnet32_rx_head rx_ring[RX_RING_SIZE]; - struct pcnet32_tx_head tx_ring[TX_RING_SIZE]; - struct pcnet32_init_block init_block; - dma_addr_t dma_addr; /* DMA address of beginning of this object, returned by pci_alloc_consistent */ + struct pcnet32_rx_head *rx_ring; + struct pcnet32_tx_head *tx_ring; + struct pcnet32_init_block *init_block; + dma_addr_t rx_ring_dma; + dma_addr_t tx_ring_dma; + dma_addr_t init_block_dma; + struct pci_dev *pci_dev; /* Pointer to the associated pci device structure */ const char *name; /* The saved address of a sent-in-place packet/buffer, for skfree(). */ @@ -271,21 +277,16 @@ unsigned int cur_rx, cur_tx; /* The next free ring entry */ unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */ struct net_device_stats stats; - char tx_full; int options; - int shared_irq:1, /* shared irq possible */ - ltint:1, + int ltint:1, #ifdef DO_DXSUFLO dxsuflo:1, /* disable transmit stop on uflo */ #endif full_duplex:1, /* full duplex possible */ mii:1; /* mii port available */ - struct net_device *next; }; -static int pcnet32_probe_vlbus(int cards_found); -static int pcnet32_probe_pci(struct pci_dev *, const struct pci_device_id *); -static int pcnet32_probe1(unsigned long, unsigned char, int, int, struct pci_dev *); +static int pcnet32_probe1(int, struct pci_dev *); static int pcnet32_open(struct net_device *); static int pcnet32_init_ring(struct net_device *); static int pcnet32_start_xmit(struct sk_buff *, struct net_device *); @@ -299,26 +300,13 @@ static int pcnet32_mii_ioctl(struct net_device *, struct ifreq *, int); #endif -enum pci_flags_bit { - PCI_USES_IO=1, PCI_USES_MEM=2, PCI_USES_MASTER=4, - PCI_ADDR0=0x10<<0, PCI_ADDR1=0x10<<1, PCI_ADDR2=0x10<<2, PCI_ADDR3=0x10<<3, -}; - -struct pcnet32_pci_id_info { - const char *name; - u16 vendor_id, device_id, svid, sdid, flags; - int io_size; - int (*probe1) (unsigned long, unsigned char, int, int, struct pci_dev *); -}; - - /* * PCI device identifiers for "new style" Linux PCI Device Drivers */ -static struct pci_device_id pcnet32_pci_tbl[] __devinitdata = { +static struct pci_device_id pcnet32_pci_tbl[] __initdata = { { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_PCNETHOME, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE, 0x1014, 0x2000, 0, 0, 0 }, +/* { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE, 0x1014, 0x2000, 0, 0, 0 }, */ { 0, } }; @@ -435,52 +423,15 @@ }; -\f - -/* only probes for non-PCI devices, the rest are handled by pci_register_driver via pcnet32_probe_pci*/ -static int __init pcnet32_probe_vlbus(int cards_found) -{ - unsigned long ioaddr = 0; // FIXME dev ? dev->base_addr: 0; - unsigned int irq_line = 0; // FIXME dev ? dev->irq : 0; - int *port; - - printk(KERN_INFO "pcnet32_probe_vlbus: cards_found=%d\n", cards_found); -#ifndef __powerpc__ - if (ioaddr > 0x1ff) { - if (check_region(ioaddr, PCNET32_TOTAL_SIZE) == 0) - return pcnet32_probe1(ioaddr, irq_line, 0, 0, NULL); - else - return -ENODEV; - } else -#endif - if (ioaddr != 0) - return -ENXIO; - - /* now look for PCnet32 VLB cards */ - for (port = pcnet32_portlist; *port; port++) { - unsigned long ioaddr = *port; - - if ( check_region(ioaddr, PCNET32_TOTAL_SIZE) == 0) { - /* check if there is really a pcnet chip on that ioaddr */ - if ((inb(ioaddr + 14) == 0x57) && - (inb(ioaddr + 15) == 0x57) && - (pcnet32_probe1(ioaddr, 0, 0, 0, NULL) == 0)) - cards_found++; - } - } - return cards_found ? 0: -ENODEV; -} - - static int __init pcnet32_probe_pci(struct pci_dev *pdev, const struct pci_device_id *ent) { static int card_idx; - long ioaddr; - int err = 0; + int err; + unsigned long ioaddr; - printk(KERN_INFO "pcnet32_probe_pci: found device %#08x.%#08x\n", ent->vendor, ent->device); + printk(KERN_DEBUG "pcnet32_probe_pci: found device %#08x.%#08x\n", ent->vendor, ent->device); ioaddr = pci_resource_start (pdev, 0); printk(KERN_INFO " ioaddr=%#08lx resource_flags=%#08lx\n", ioaddr, pci_resource_flags (pdev, 0)); @@ -493,37 +444,58 @@ printk(KERN_ERR "pcnet32.c: architecture does not support 32bit PCI busmaster DMA\n"); return -ENODEV; } + pdev->dma_mask = PCNET32_DMA_MASK; - if ((err = pci_enable_device(pdev)) < 0) { + err = pci_enable_device(pdev); + if (err) { printk(KERN_ERR "pcnet32.c: failed to enable device -- err=%d\n", err); return err; } - + pci_set_master(pdev); - - return pcnet32_probe1(ioaddr, pdev->irq, 1, card_idx, pdev); + + err = pcnet32_probe1(card_idx, pdev); + + if (err == 0) + card_idx++; + + return err; } -/* pcnet32_probe1 - * Called from both pcnet32_probe_vlbus and pcnet_probe_pci. - * pdev will be NULL when called from pcnet32_probe_vlbus. +/* pcnet32_probe1 + * Called from both pcnet32_probe_vlbus and pcnet_probe_pci. */ static int __init -pcnet32_probe1(unsigned long ioaddr, unsigned char irq_line, int shared, int card_idx, struct pci_dev *pdev) +pcnet32_probe1(int card_idx, struct pci_dev *pdev) { struct pcnet32_private *lp; - dma_addr_t lp_dma_addr; int i,media,fdx = 0, mii = 0, fset = 0; #ifdef DO_DXSUFLO int dxsuflo = 0; #endif int ltint = 0; - int chip_version; + int chip_version, ret = -ENODEV; char *chipname; struct net_device *dev; struct pcnet32_access *a = NULL; + unsigned long ioaddr = pci_resource_start(pdev, 0); + if (!ioaddr) { + printk (KERN_ERR "no PCI IO resources, aborting\n"); + return -ENODEV; + } + + dev = init_etherdev(NULL, sizeof(*lp)); + if (dev == NULL) + return -ENOMEM; + SET_MODULE_OWNER(dev); + + if (!request_region(ioaddr, PCNET32_TOTAL_SIZE, dev->name)) { + ret = -EBUSY; + goto err_out; + } + /* reset the chip */ pcnet32_dwio_reset(ioaddr); pcnet32_wio_reset(ioaddr); @@ -534,24 +506,21 @@ if (pcnet32_dwio_read_csr (ioaddr, 0) == 4 && pcnet32_dwio_check(ioaddr)) { a = &pcnet32_dwio; } else - return -ENODEV; + goto err_out_res; } chip_version = a->read_csr (ioaddr, 88) | (a->read_csr (ioaddr,89) << 16); if (pcnet32_debug > 2) printk(KERN_INFO " PCnet chip version is %#x.\n", chip_version); if ((chip_version & 0xfff) != 0x003) - return -ENODEV; + goto err_out_res; chip_version = (chip_version >> 12) & 0xffff; switch (chip_version) { case 0x2420: chipname = "PCnet/PCI 79C970"; /* PCI */ break; case 0x2430: - if (shared) - chipname = "PCnet/PCI 79C970"; /* 970 gives the wrong chip id back */ - else - chipname = "PCnet/32 79C965"; /* 486/VL bus */ + chipname = "PCnet/PCI 79C970"; /* 970 gives the wrong chip id back */ break; case 0x2621: chipname = "PCnet/PCI II 79C970A"; /* PCI */ @@ -573,7 +542,7 @@ case 0x2626: chipname = "PCnet/Home 79C978"; /* PCI */ fdx = 1; - /* + /* * This is based on specs published at www.amd.com. This section * assumes that a card with a 79C978 wants to go into 1Mb HomePNA * mode. The 79C978 can also go into standard ethernet, and there @@ -598,16 +567,16 @@ break; default: printk(KERN_INFO "pcnet32: PCnet version %#x, no PCnet32 chip.\n",chip_version); - return -ENODEV; + goto err_out_res; } /* * On selected chips turn on the BCR18:NOUFLO bit. This stops transmit * starting until the packet is loaded. Strike one for reliability, lose - * one for latency - although on PCI this isnt a big loss. Older chips + * one for latency - although on PCI this isnt a big loss. Older chips * have FIFO's smaller than a packet, so you can't do this. */ - + if(fset) { a->write_bcr(ioaddr, 18, (a->read_bcr(ioaddr, 18) | 0x0800)); @@ -617,10 +586,6 @@ #endif ltint = 1; } - - dev = init_etherdev(NULL, 0); - if(dev==NULL) - return -ENOMEM; printk(KERN_INFO "%s: %s at %#3lx,", dev->name, chipname, ioaddr); @@ -653,22 +618,29 @@ } dev->base_addr = ioaddr; - request_region(ioaddr, PCNET32_TOTAL_SIZE, chipname); - - /* pci_alloc_consistent returns page-aligned memory, so we do not have to check the alignment */ - if ((lp = (struct pcnet32_private *)pci_alloc_consistent(pdev, sizeof(*lp), &lp_dma_addr)) == NULL) - return -ENOMEM; - memset(lp, 0, sizeof(*lp)); - lp->dma_addr = lp_dma_addr; - lp->pci_dev = pdev; - printk("\n" KERN_INFO "pcnet32: pcnet32_private lp=%p lp_dma_addr=%#08x", lp, lp_dma_addr); + lp = dev->priv; + lp->rx_ring = pci_alloc_consistent(pdev, DMA_ALLOC_SIZE, &lp->rx_ring_dma); + if (!lp->rx_ring) { + ret = -ENOMEM; + goto err_out_res; + } + + printk(KERN_INFO "pcnet32: pcnet32_private lp=%p lp_dma_addr=%#08x\n", lp, lp->rx_ring_dma); + + lp->tx_ring = ((void*)lp->rx_ring) + + sizeof(struct pcnet32_rx_head) * RX_RING_SIZE; + lp->init_block = ((void*)lp->tx_ring) + + sizeof(struct pcnet32_rx_head) * TX_RING_SIZE; + lp->tx_ring_dma = lp->rx_ring_dma + + sizeof(struct pcnet32_rx_head) * RX_RING_SIZE; + lp->init_block_dma = lp->tx_ring_dma + + sizeof(struct pcnet32_rx_head) * TX_RING_SIZE; + spin_lock_init(&lp->lock); - - dev->priv = lp; + lp->pci_dev = pdev; lp->name = chipname; - lp->shared_irq = shared; lp->full_duplex = fdx; #ifdef DO_DXSUFLO lp->dxsuflo = dxsuflo; @@ -679,44 +651,43 @@ lp->options = PORT_ASEL; else lp->options = options_mapping[options[card_idx]]; - + if (fdx && !(lp->options & PORT_ASEL) && full_duplex[card_idx]) lp->options |= PORT_FD; - + if (a == NULL) { printk(KERN_ERR "pcnet32: No access methods\n"); - return -ENODEV; + goto err_out_dma_mem; } lp->a = *a; - + /* detect special T1/E1 WAN card by checking for MAC address */ if (dev->dev_addr[0] == 0x00 && dev->dev_addr[1] == 0xe0 && dev->dev_addr[2] == 0x75) lp->options = PORT_FD | PORT_GPSI; - lp->init_block.mode = le16_to_cpu(0x0003); /* Disable Rx and Tx. */ - lp->init_block.tlen_rlen = le16_to_cpu(TX_RING_LEN_BITS | RX_RING_LEN_BITS); + lp->init_block->mode = cpu_to_le16(0x0003); /* Disable Rx and Tx. */ + lp->init_block->tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS | RX_RING_LEN_BITS); for (i = 0; i < 6; i++) - lp->init_block.phys_addr[i] = dev->dev_addr[i]; - lp->init_block.filter[0] = 0x00000000; - lp->init_block.filter[1] = 0x00000000; - lp->init_block.rx_ring = (u32)le32_to_cpu(lp->dma_addr + offsetof(struct pcnet32_private, rx_ring)); - lp->init_block.tx_ring = (u32)le32_to_cpu(lp->dma_addr + offsetof(struct pcnet32_private, tx_ring)); - + lp->init_block->phys_addr[i] = dev->dev_addr[i]; + lp->init_block->filter[0] = 0x00000000; + lp->init_block->filter[1] = 0x00000000; + lp->init_block->rx_ring = cpu_to_le32(lp->rx_ring_dma); + lp->init_block->tx_ring = cpu_to_le32(lp->tx_ring_dma); + /* switch pcnet32 to 32bit mode */ a->write_bcr (ioaddr, 20, 2); - a->write_csr (ioaddr, 1, (lp->dma_addr + offsetof(struct pcnet32_private, init_block)) & 0xffff); - a->write_csr (ioaddr, 2, (lp->dma_addr + offsetof(struct pcnet32_private, init_block)) >> 16); - - if (irq_line) { - dev->irq = irq_line; - } - + /* XXX endian problems here? */ + a->write_csr (ioaddr, 1, lp->init_block_dma & 0xffff); + a->write_csr (ioaddr, 2, lp->init_block_dma >> 16); + + dev->irq = pdev->irq; + if (dev->irq >= 2) printk(" assigned IRQ %d.\n", dev->irq); else { unsigned long irq_mask = probe_irq_on(); - + /* * To auto-IRQ we enable the initialization-done and DMA error * interrupts. For ISA boards we get a DMA error, but VLB and PCI @@ -725,7 +696,7 @@ /* Trigger an initialization just for the interrupt. */ a->write_csr (ioaddr, 0, 0x41); mdelay (1); - + dev->irq = probe_irq_off (irq_mask); if (dev->irq) printk(", probed IRQ %d.\n", dev->irq); @@ -737,7 +708,7 @@ if (pcnet32_debug > 0) printk(KERN_INFO "%s", version); - + /* The PCNET32-specific entries in the device structure. */ dev->open = &pcnet32_open; dev->hard_start_xmit = &pcnet32_start_xmit; @@ -748,30 +719,32 @@ dev->do_ioctl = &pcnet32_mii_ioctl; #endif dev->tx_timeout = pcnet32_tx_timeout; - dev->watchdog_timeo = (HZ >> 1); - - lp->next = pcnet32_dev; - pcnet32_dev = dev; + dev->watchdog_timeo = (1 * HZ); - /* Fill in the generic fields of the device structure. */ - ether_setup(dev); + pci_set_drvdata(pdev, dev); return 0; + +err_out_dma_mem: + pci_free_consistent(pdev, DMA_ALLOC_SIZE, lp->rx_ring, lp->rx_ring_dma); +err_out_res: + release_region(ioaddr, PCNET32_TOTAL_SIZE); +err_out: + unregister_netdev(dev); + kfree(dev); + return ret; } + -\f static int pcnet32_open(struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; unsigned long ioaddr = dev->base_addr; u16 val; - int i; + int i, ret; - if (dev->irq == 0 || - request_irq(dev->irq, &pcnet32_interrupt, - lp->shared_irq ? SA_SHIRQ : 0, lp->name, (void *)dev)) { - return -EAGAIN; - } + ret = request_irq(dev->irq, &pcnet32_interrupt, SA_SHIRQ, lp->name, dev); + if (ret) return ret; /* Reset the PCNET32 */ lp->a.reset (ioaddr); @@ -781,17 +754,15 @@ if (pcnet32_debug > 1) printk(KERN_DEBUG "%s: pcnet32_open() irq %d tx/rx rings %#x/%#x init %#x.\n", - dev->name, dev->irq, - (u32) (lp->dma_addr + offsetof(struct pcnet32_private, tx_ring)), - (u32) (lp->dma_addr + offsetof(struct pcnet32_private, rx_ring)), - (u32) (lp->dma_addr + offsetof(struct pcnet32_private, init_block))); - + dev->name, dev->irq, (u32) lp->tx_ring_dma, + (u32) lp->rx_ring_dma, (u32) lp->init_block_dma); + /* set/reset autoselect bit */ val = lp->a.read_bcr (ioaddr, 2) & ~2; if (lp->options & PORT_ASEL) val |= 2; lp->a.write_bcr (ioaddr, 2, val); - + /* handle full duplex setting */ if (lp->full_duplex) { val = lp->a.read_bcr (ioaddr, 9) & ~3; @@ -802,13 +773,13 @@ } lp->a.write_bcr (ioaddr, 9, val); } - + /* set/reset GPSI bit in test register */ val = lp->a.read_csr (ioaddr, 124) & ~0x10; if ((lp->options & PORT_PORTSEL) == PORT_GPSI) val |= 0x10; lp->a.write_csr (ioaddr, 124, val); - + if (lp->mii & !(lp->options & PORT_ASEL)) { val = lp->a.read_bcr (ioaddr, 32) & ~0x38; /* disable Auto Negotiation, set 10Mpbs, HD */ if (lp->options & PORT_FD) @@ -818,7 +789,7 @@ lp->a.write_bcr (ioaddr, 32, val); } -#ifdef DO_DXSUFLO +#ifdef DO_DXSUFLO if (lp->dxsuflo) { /* Disable transmit stop on underflow */ val = lp->a.read_csr (ioaddr, 3); val |= 0x40; @@ -830,16 +801,25 @@ val |= (1<<14); lp->a.write_csr (ioaddr, 5, val); } - - lp->init_block.mode = le16_to_cpu((lp->options & PORT_PORTSEL) << 7); - lp->init_block.filter[0] = 0x00000000; - lp->init_block.filter[1] = 0x00000000; - if (pcnet32_init_ring(dev)) - return -ENOMEM; - + + lp->init_block->mode = cpu_to_le16((lp->options & PORT_PORTSEL) << 7); + lp->init_block->filter[0] = 0x00000000; + lp->init_block->filter[1] = 0x00000000; + ret = pcnet32_init_ring(dev); + if (ret) { + free_irq(dev->irq, dev); + for (i = 0; i < RX_RING_SIZE; i++) + if (lp->rx_skbuff[i]) { + dev_kfree_skb(lp->rx_skbuff[i]); + lp->rx_skbuff[i] = NULL; + } + return ret; + } + /* Re-initialize the PCNET32, and start it when done. */ - lp->a.write_csr (ioaddr, 1, (lp->dma_addr + offsetof(struct pcnet32_private, init_block)) &0xffff); - lp->a.write_csr (ioaddr, 2, (lp->dma_addr + offsetof(struct pcnet32_private, init_block)) >> 16); + /* XXX endian problems here? */ + lp->a.write_csr (ioaddr, 1, lp->init_block_dma & 0xffff); + lp->a.write_csr (ioaddr, 2, lp->init_block_dma >> 16); lp->a.write_csr (ioaddr, 4, 0x0915); lp->a.write_csr (ioaddr, 0, 0x0001); @@ -850,7 +830,7 @@ while (i++ < 100) if (lp->a.read_csr (ioaddr, 0) & 0x0100) break; - /* + /* * We used to clear the InitDone bit, 0x0100, here but Mark Stockton * reports that doing so triggers a bug in the '974. */ @@ -858,13 +838,10 @@ if (pcnet32_debug > 2) printk(KERN_DEBUG "%s: pcnet32 open after %d ticks, init block %#x csr0 %4.4x.\n", - dev->name, i, (u32) (lp->dma_addr + offsetof(struct pcnet32_private, init_block)), + dev->name, i, (u32) lp->init_block_dma, lp->a.read_csr (ioaddr, 0)); - - MOD_INC_USE_COUNT; - - return 0; /* Always succeed */ + return 0; } /* @@ -880,16 +857,16 @@ * restarting the chip, but I'm too lazy to do so right now. dplatt@3do.com */ -static void +static void pcnet32_purge_tx_ring(struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; int i; for (i = 0; i < TX_RING_SIZE; i++) { if (lp->tx_skbuff[i]) { pci_unmap_single(lp->pci_dev, lp->tx_dma_addr[i], lp->tx_skbuff[i]->len, PCI_DMA_TODEVICE); - dev_kfree_skb(lp->tx_skbuff[i]); + dev_kfree_skb_any(lp->tx_skbuff[i]); lp->tx_skbuff[i] = NULL; lp->tx_dma_addr[i] = 0; } @@ -901,10 +878,9 @@ static int pcnet32_init_ring(struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; int i; - lp->tx_full = 0; lp->cur_rx = lp->cur_tx = 0; lp->dirty_rx = lp->dirty_tx = 0; @@ -914,14 +890,14 @@ if (!(rx_skbuff = lp->rx_skbuff[i] = dev_alloc_skb (PKT_BUF_SZ))) { /* there is not much, we can do at this point */ printk(KERN_ERR "%s: pcnet32_init_ring dev_alloc_skb failed.\n",dev->name); - return -1; + return -ENOMEM; } skb_reserve (rx_skbuff, 2); } lp->rx_dma_addr[i] = pci_map_single(lp->pci_dev, rx_skbuff->tail, rx_skbuff->len, PCI_DMA_FROMDEVICE); - lp->rx_ring[i].base = (u32)le32_to_cpu(lp->rx_dma_addr[i]); - lp->rx_ring[i].buf_length = le16_to_cpu(-PKT_BUF_SZ); - lp->rx_ring[i].status = le16_to_cpu(0x8000); + lp->rx_ring[i].base = cpu_to_le32(lp->rx_dma_addr[i]); + lp->rx_ring[i].buf_length = cpu_to_le16(-PKT_BUF_SZ); + lp->rx_ring[i].status = cpu_to_le16(0x8000); } /* The Tx buffer address is filled in as needed, but we do need to clear the upper ownership bit. */ @@ -931,25 +907,25 @@ lp->tx_dma_addr[i] = 0; } - lp->init_block.tlen_rlen = le16_to_cpu(TX_RING_LEN_BITS | RX_RING_LEN_BITS); + lp->init_block->tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS | RX_RING_LEN_BITS); for (i = 0; i < 6; i++) - lp->init_block.phys_addr[i] = dev->dev_addr[i]; - lp->init_block.rx_ring = (u32)le32_to_cpu(lp->dma_addr + offsetof(struct pcnet32_private, rx_ring)); - lp->init_block.tx_ring = (u32)le32_to_cpu(lp->dma_addr + offsetof(struct pcnet32_private, tx_ring)); + lp->init_block->phys_addr[i] = dev->dev_addr[i]; + lp->init_block->rx_ring = cpu_to_le32(lp->rx_ring_dma); + lp->init_block->tx_ring = cpu_to_le32(lp->tx_ring_dma); return 0; } static void pcnet32_restart(struct net_device *dev, unsigned int csr0_bits) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; unsigned long ioaddr = dev->base_addr; int i; - + pcnet32_purge_tx_ring(dev); if (pcnet32_init_ring(dev)) return; - + /* ReInit Ring */ lp->a.write_csr (ioaddr, 0, 1); i = 0; @@ -964,30 +940,41 @@ static void pcnet32_tx_timeout (struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; - unsigned int ioaddr = dev->base_addr; + struct pcnet32_private *lp = dev->priv; + unsigned int ioaddr = dev->base_addr; - /* Transmitter timeout, serious problems. */ + /* Transmitter timeout, serious problems. */ printk(KERN_ERR "%s: transmit timed out, status %4.4x, resetting.\n", dev->name, lp->a.read_csr (ioaddr, 0)); + + spin_lock_irq(&lp->lock); lp->a.write_csr (ioaddr, 0, 0x0004); + spin_unlock_irq(&lp->lock); + lp->stats.tx_errors++; if (pcnet32_debug > 2) { int i; printk(KERN_DEBUG " Ring data dump: dirty_tx %d cur_tx %d%s cur_rx %d.", - lp->dirty_tx, lp->cur_tx, lp->tx_full ? " (full)" : "", + lp->dirty_tx, lp->cur_tx, netif_queue_stopped(dev) ? " (full)" : "", lp->cur_rx); for (i = 0 ; i < RX_RING_SIZE; i++) printk("%s %08x %04x %08x %04x", i & 1 ? "" : "\n ", - lp->rx_ring[i].base, -lp->rx_ring[i].buf_length, - lp->rx_ring[i].msg_length, (unsigned)lp->rx_ring[i].status); + le32_to_cpu(lp->rx_ring[i].base), + -le16_to_cpu(lp->rx_ring[i].buf_length), + le32_to_cpu(lp->rx_ring[i].msg_length), + (unsigned)le16_to_cpu(lp->rx_ring[i].status)); for (i = 0 ; i < TX_RING_SIZE; i++) printk("%s %08x %04x %08x %04x", i & 1 ? "" : "\n ", - lp->tx_ring[i].base, -lp->tx_ring[i].length, - lp->tx_ring[i].misc, (unsigned)lp->tx_ring[i].status); - printk("\n"); + le32_to_cpu(lp->tx_ring[i].base), + -le16_to_cpu(lp->tx_ring[i].length), + le32_to_cpu(lp->tx_ring[i].misc), + (unsigned)le16_to_cpu(lp->tx_ring[i].status)); + printk(KERN_DEBUG "\n"); } + + spin_lock_irq(&lp->lock); pcnet32_restart(dev, 0x0042); + spin_unlock_irq(&lp->lock); dev->trans_start = jiffies; netif_start_queue(dev); @@ -997,19 +984,18 @@ static int pcnet32_start_xmit(struct sk_buff *skb, struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; unsigned int ioaddr = dev->base_addr; u16 status; int entry; - unsigned long flags; if (pcnet32_debug > 3) { + spin_lock_irq(&lp->lock); printk(KERN_DEBUG "%s: pcnet32_start_xmit() called, csr0 %4.4x.\n", dev->name, lp->a.read_csr (ioaddr, 0)); + spin_unlock_irq(&lp->lock); } - spin_lock_irqsave(&lp->lock, flags); - /* Default status -- will not enable Successful-TxDone * interrupt when that option is available to us. */ @@ -1025,39 +1011,39 @@ */ status = 0x9300; } - + /* Fill in a Tx ring entry */ - + /* Mask to ring buffer boundary. */ entry = lp->cur_tx & TX_RING_MOD_MASK; - + /* Caution: the write order is important here, set the base address with the "ownership" bits last. */ - lp->tx_ring[entry].length = le16_to_cpu(-skb->len); + lp->tx_ring[entry].length = cpu_to_le16(-skb->len); lp->tx_ring[entry].misc = 0x00000000; lp->tx_skbuff[entry] = skb; lp->tx_dma_addr[entry] = pci_map_single(lp->pci_dev, skb->data, skb->len, PCI_DMA_TODEVICE); - lp->tx_ring[entry].base = (u32)le32_to_cpu(lp->tx_dma_addr[entry]); - lp->tx_ring[entry].status = le16_to_cpu(status); + lp->tx_ring[entry].base = cpu_to_le32(lp->tx_dma_addr[entry]); + lp->tx_ring[entry].status = cpu_to_le16(status); lp->cur_tx++; lp->stats.tx_bytes += skb->len; /* Trigger an immediate send poll. */ + spin_lock_irq(&lp->lock); lp->a.write_csr (ioaddr, 0, 0x0048); + spin_unlock_irq(&lp->lock); dev->trans_start = jiffies; - if (lp->tx_ring[(entry+1) & TX_RING_MOD_MASK].base == 0) - netif_start_queue(dev); - else { - lp->tx_full = 1; + if ((lp->cur_tx - lp->dirty_tx) > TX_RING_SIZE) + BUG(); + if ((lp->cur_tx - lp->dirty_tx) == TX_RING_SIZE) netif_stop_queue(dev); - } - spin_unlock_irqrestore(&lp->lock, flags); + return 0; } @@ -1065,7 +1051,7 @@ static void pcnet32_interrupt(int irq, void *dev_id, struct pt_regs * regs) { - struct net_device *dev = (struct net_device *)dev_id; + struct net_device *dev = dev_id; struct pcnet32_private *lp; unsigned long ioaddr; u16 csr0,rap; @@ -1078,10 +1064,10 @@ } ioaddr = dev->base_addr; - lp = (struct pcnet32_private *)dev->priv; - + lp = dev->priv; + spin_lock(&lp->lock); - + rap = lp->a.read_rap(ioaddr); while ((csr0 = lp->a.read_csr (ioaddr, 0)) & 0x8600 && --boguscnt >= 0) { /* Acknowledge all of the current interrupt sources ASAP. */ @@ -1102,7 +1088,7 @@ while (dirty_tx < lp->cur_tx) { int entry = dirty_tx & TX_RING_MOD_MASK; int status = (short)le16_to_cpu(lp->tx_ring[entry].status); - + if (status < 0) break; /* It still hasn't been Txed */ @@ -1155,17 +1141,15 @@ #ifndef final_version if (lp->cur_tx - dirty_tx >= TX_RING_SIZE) { printk(KERN_ERR "out-of-sync dirty pointer, %d vs. %d, full=%d.\n", - dirty_tx, lp->cur_tx, lp->tx_full); + dirty_tx, lp->cur_tx, netif_queue_stopped(dev) ? 1 : 0); dirty_tx += TX_RING_SIZE; } #endif - if (lp->tx_full && - netif_queue_stopped(dev) && - dirty_tx > lp->cur_tx - TX_RING_SIZE + 2) { - /* The ring is no longer full, clear tbusy. */ - lp->tx_full = 0; + /* If the ring is no longer full, accept more packets. */ + if (netif_queue_stopped(dev) && + (dirty_tx > lp->cur_tx - TX_RING_SIZE + 2)) netif_wake_queue (dev); - } + lp->dirty_tx = dirty_tx; } @@ -1200,7 +1184,7 @@ /* Clear any other interrupt, and set interrupt enable. */ lp->a.write_csr (ioaddr, 0, 0x7940); lp->a.write_rap(ioaddr,rap); - + if (pcnet32_debug > 4) printk(KERN_DEBUG "%s: exiting interrupt, csr0=%#4.4x.\n", dev->name, lp->a.read_csr (ioaddr, 0)); @@ -1211,7 +1195,7 @@ static int pcnet32_rx(struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; int entry = lp->cur_rx & RX_RING_MOD_MASK; /* If we own the next entry, it's a new packet. Send it up. */ @@ -1219,7 +1203,7 @@ int status = (short)le16_to_cpu(lp->rx_ring[entry].status) >> 8; if (status != 0x03) { /* There was an error. */ - /* + /* * There is a tricky error noted by John Murphy, * <murf@perftech.com> to Russ Nelson: Even with full-sized * buffers it's possible for a jabber packet to use two @@ -1231,12 +1215,13 @@ if (status & 0x10) lp->stats.rx_over_errors++; if (status & 0x08) lp->stats.rx_crc_errors++; if (status & 0x04) lp->stats.rx_fifo_errors++; - lp->rx_ring[entry].status &= le16_to_cpu(0x03ff); + lp->rx_ring[entry].status = + cpu_to_le16(le16_to_cpu(lp->rx_ring[entry].status) & 0x03ff); } else { /* Malloc up new buffer, compatible with net-2e. */ short pkt_len = (le32_to_cpu(lp->rx_ring[entry].msg_length) & 0xfff)-4; struct sk_buff *skb; - + if(pkt_len < 60) { printk(KERN_ERR "%s: Runt packet!\n",dev->name); lp->stats.rx_errors++; @@ -1245,7 +1230,7 @@ if (pkt_len > rx_copybreak) { struct sk_buff *newskb; - + if ((newskb = dev_alloc_skb (PKT_BUF_SZ))) { skb_reserve (newskb, 2); skb = lp->rx_skbuff[entry]; @@ -1253,14 +1238,14 @@ lp->rx_skbuff[entry] = newskb; newskb->dev = dev; lp->rx_dma_addr[entry] = pci_map_single(lp->pci_dev, newskb->tail, newskb->len, PCI_DMA_FROMDEVICE); - lp->rx_ring[entry].base = le32_to_cpu(lp->rx_dma_addr[entry]); + lp->rx_ring[entry].base = cpu_to_le32(lp->rx_dma_addr[entry]); rx_in_place = 1; } else skb = NULL; } else { skb = dev_alloc_skb(pkt_len+2); } - + if (skb == NULL) { int i; printk(KERN_ERR "%s: Memory squeeze, deferring packet.\n", dev->name); @@ -1270,7 +1255,8 @@ if (i > RX_RING_SIZE -2) { lp->stats.rx_dropped++; - lp->rx_ring[entry].status |= le16_to_cpu(0x8000); + lp->rx_ring[entry].status = + cpu_to_le16(le16_to_cpu(lp->rx_ring[entry].status) | 0x8000); lp->cur_rx++; } break; @@ -1293,8 +1279,9 @@ * The docs say that the buffer length isn't touched, but Andrew Boyd * of QNX reports that some revs of the 79C965 clear it. */ - lp->rx_ring[entry].buf_length = le16_to_cpu(-PKT_BUF_SZ); - lp->rx_ring[entry].status |= le16_to_cpu(0x8000); + lp->rx_ring[entry].buf_length = cpu_to_le16(-PKT_BUF_SZ); + lp->rx_ring[entry].status = + cpu_to_le16(le16_to_cpu(lp->rx_ring[entry].status) | 0x8000); entry = (++lp->cur_rx) & RX_RING_MOD_MASK; } @@ -1305,11 +1292,13 @@ pcnet32_close(struct net_device *dev) { unsigned long ioaddr = dev->base_addr; - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; int i; netif_stop_queue(dev); + spin_lock_irq(&lp->lock); + lp->stats.rx_missed_errors = lp->a.read_csr (ioaddr, 112); if (pcnet32_debug > 1) @@ -1320,16 +1309,19 @@ lp->a.write_csr (ioaddr, 0, 0x0004); /* - * Switch back to 16bit mode to avoid problems with dumb + * Switch back to 16bit mode to avoid problems with dumb * DOS packet driver after a warm reboot */ lp->a.write_bcr (ioaddr, 20, 4); + spin_unlock_irq(&lp->lock); + synchronize_irq(); + free_irq(dev->irq, dev); - + /* free all allocated skbuffs */ for (i = 0; i < RX_RING_SIZE; i++) { - lp->rx_ring[i].status = 0; + lp->rx_ring[i].status = 0; if (lp->rx_skbuff[i]) { pci_unmap_single(lp->pci_dev, lp->rx_dma_addr[i], lp->rx_skbuff[i]->len, PCI_DMA_FROMDEVICE); dev_kfree_skb(lp->rx_skbuff[i]); @@ -1337,7 +1329,7 @@ lp->rx_skbuff[i] = NULL; lp->rx_dma_addr[i] = 0; } - + for (i = 0; i < TX_RING_SIZE; i++) { if (lp->tx_skbuff[i]) { pci_unmap_single(lp->pci_dev, lp->tx_dma_addr[i], lp->tx_skbuff[i]->len, PCI_DMA_TODEVICE); @@ -1346,8 +1338,6 @@ lp->tx_skbuff[i] = NULL; lp->tx_dma_addr[i] = 0; } - - MOD_DEC_USE_COUNT; return 0; } @@ -1355,16 +1345,15 @@ static struct net_device_stats * pcnet32_get_stats(struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; unsigned long ioaddr = dev->base_addr; u16 saved_addr; - unsigned long flags; - spin_lock_irqsave(&lp->lock, flags); + spin_lock_irq(&lp->lock); saved_addr = lp->a.read_rap(ioaddr); lp->stats.rx_missed_errors = lp->a.read_csr (ioaddr, 112); lp->a.write_rap(ioaddr, saved_addr); - spin_unlock_irqrestore(&lp->lock, flags); + spin_unlock_irq(&lp->lock); return &lp->stats; } @@ -1372,16 +1361,16 @@ /* taken from the sunlance driver, which it took from the depca driver */ static void pcnet32_load_multicast (struct net_device *dev) { - struct pcnet32_private *lp = (struct pcnet32_private *) dev->priv; - volatile struct pcnet32_init_block *ib = &lp->init_block; + struct pcnet32_private *lp = dev->priv; + volatile struct pcnet32_init_block *ib = lp->init_block; volatile u16 *mcast_table = (u16 *)&ib->filter; struct dev_mc_list *dmi=dev->mc_list; char *addrs; int i, j, bit, byte; u32 crc, poly = CRC_POLYNOMIAL_LE; - + /* set all multicast bits */ - if (dev->flags & IFF_ALLMULTI){ + if (dev->flags & IFF_ALLMULTI){ ib->filter [0] = 0xffffffff; ib->filter [1] = 0xffffffff; return; @@ -1394,24 +1383,24 @@ for (i = 0; i < dev->mc_count; i++){ addrs = dmi->dmi_addr; dmi = dmi->next; - + /* multicast address? */ if (!(*addrs & 1)) continue; - + crc = 0xffffffff; for (byte = 0; byte < 6; byte++) for (bit = *addrs++, j = 0; j < 8; j++, bit >>= 1) { int test; - + test = ((bit ^ crc) & 0x01); crc >>= 1; - + if (test) { crc = crc ^ poly; } } - + crc = crc >> 26; mcast_table [crc >> 4] |= 1 << (crc & 0xf); } @@ -1425,30 +1414,38 @@ static void pcnet32_set_multicast_list(struct net_device *dev) { unsigned long ioaddr = dev->base_addr; - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; + + spin_lock_irq(&lp->lock); if (dev->flags&IFF_PROMISC) { /* Log any net taps. */ printk(KERN_INFO "%s: Promiscuous mode enabled.\n", dev->name); - lp->init_block.mode = le16_to_cpu(0x8000 | (lp->options & PORT_PORTSEL) << 7); + lp->init_block->mode = cpu_to_le16(0x8000 | (lp->options & PORT_PORTSEL) << 7); } else { - lp->init_block.mode = le16_to_cpu((lp->options & PORT_PORTSEL) << 7); + lp->init_block->mode = cpu_to_le16((lp->options & PORT_PORTSEL) << 7); pcnet32_load_multicast (dev); } - + lp->a.write_csr (ioaddr, 0, 0x0004); /* Temporarily stop the lance. */ pcnet32_restart(dev, 0x0042); /* Resume normal operation */ + + spin_unlock_irq(&lp->lock); } #ifdef HAVE_PRIVATE_IOCTL static int pcnet32_mii_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) { unsigned long ioaddr = dev->base_addr; - struct pcnet32_private *lp = (struct pcnet32_private *)dev->priv; + struct pcnet32_private *lp = dev->priv; u16 *data = (u16 *)&rq->ifr_data; - int phyaddr = lp->a.read_bcr (ioaddr, 33); + int ret = -EOPNOTSUPP, phyaddr; + + spin_lock_irq(&lp->lock); + phyaddr = lp->a.read_bcr (ioaddr, 33); + if (lp->mii) { switch(cmd) { case SIOCDEVPRIVATE: /* Get the address of the PHY in use. */ @@ -1458,27 +1455,45 @@ lp->a.write_bcr (ioaddr, 33, ((data[0] & 0x1f) << 5) | (data[1] & 0x1f)); data[3] = lp->a.read_bcr (ioaddr, 34); lp->a.write_bcr (ioaddr, 33, phyaddr); - return 0; + ret = 0; + break; case SIOCDEVPRIVATE+2: /* Write the specified MII register */ if (!capable(CAP_NET_ADMIN)) return -EPERM; lp->a.write_bcr (ioaddr, 33, ((data[0] & 0x1f) << 5) | (data[1] & 0x1f)); lp->a.write_bcr (ioaddr, 34, data[2]); lp->a.write_bcr (ioaddr, 33, phyaddr); - return 0; - default: - return -EOPNOTSUPP; + ret = 0; + break; + default: /* do nothing */ + break; } } - return -EOPNOTSUPP; + + spin_unlock_irq(&lp->lock); + return ret; } #endif /* HAVE_PRIVATE_IOCTL */ - + +static void __exit pcnet32_remove_one (struct pci_dev *pdev) +{ + struct net_device *dev = pci_get_drvdata(pdev); + struct pcnet32_private *lp = dev->priv; + + if (!dev) + BUG(); + unregister_netdev(dev); + release_region(dev->base_addr, PCNET32_TOTAL_SIZE); + pci_free_consistent(pdev, DMA_ALLOC_SIZE, lp->rx_ring, lp->rx_ring_dma); + kfree(dev); + pci_set_drvdata(pdev, NULL); +} + static struct pci_driver pcnet32_driver = { - name: "pcnet32", - probe: pcnet32_probe_pci, - remove: NULL, - id_table: pcnet32_pci_tbl, + name: "pcnet32", + probe: pcnet32_probe_pci, + remove: pcnet32_remove_one, + id_table: pcnet32_pci_tbl, }; MODULE_PARM(debug, "i"); @@ -1496,52 +1511,29 @@ static int __init pcnet32_init_module(void) { - int cards_found = 0; - int err; + int cards_found; if (debug > 0) pcnet32_debug = debug; + if ((tx_start_pt >= 0) && (tx_start_pt <= 3)) tx_start = tx_start_pt; - - pcnet32_dev = NULL; + /* find the PCI devices */ -#define USE_PCI_REGISTER_DRIVER -#ifdef USE_PCI_REGISTER_DRIVER - if ((err = pci_module_init(&pcnet32_driver)) < 0 ) - return err; -#else - { - struct pci_device_id *devid = pcnet32_pci_tbl; - for (devid = pcnet32_pci_tbl; devid != NULL && devid->vendor != 0; devid++) { - struct pci_dev *pdev = pci_find_subsys(devid->vendor, devid->device, devid->subvendor, devid->subdevice, NULL); - if (pdev != NULL) { - if (pcnet32_probe_pci(pdev, devid) >= 0) { - cards_found++; - } - } - } + cards_found = pci_register_driver(&pcnet32_driver); + if (cards_found < 0) + return cards_found; + if (cards_found == 0) { + pci_unregister_driver(&pcnet32_driver); + return -ENODEV; } -#endif + return 0; - /* find any remaining VLbus devices */ - return pcnet32_probe_vlbus(cards_found); } static void __exit pcnet32_cleanup_module(void) { - struct net_device *next_dev; - - /* No need to check MOD_IN_USE, as sys_delete_module() checks. */ - while (pcnet32_dev) { - struct pcnet32_private *lp = (struct pcnet32_private *) pcnet32_dev->priv; - next_dev = lp->next; - unregister_netdev(pcnet32_dev); - release_region(pcnet32_dev->base_addr, PCNET32_TOTAL_SIZE); - pci_free_consistent(lp->pci_dev, sizeof(*lp), lp, lp->dma_addr); - kfree(pcnet32_dev); - pcnet32_dev = next_dev; - } + pci_unregister_driver(&pcnet32_driver); } module_init(pcnet32_init_module); ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 14:32 ` Jeff Garzik @ 2001-01-11 16:33 ` Danny ter Haar 2001-01-11 16:44 ` Hans Grobler 0 siblings, 1 reply; 31+ messages in thread From: Danny ter Haar @ 2001-01-11 16:33 UTC (permalink / raw) To: linux-kernel Jeff Garzik <jgarzik@mandrakesoft.com> wrote: >Does this patch help at all? Nope, unfortunatly it didn't > filename="pcnet32.patch" pcnet32_probe_pci: found device 0x001022.0x002000 ioaddr=0x00fce0 resource_flags=0x000101 PCI: Found IRQ 9 for device 00:0f.0 PCnet chip version is 0x22625003. eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d<6>pcnet32: pcnet32_priv ate lp=c3fb8d40 lp_dma_addr=0x3bf1000 assigned IRQ 9. pcnet32.c:v1.25smp Nov 11, 2000 tsbogend@alpha.franken.de eth0: pcnet32_open() irq 9 tx/rx rings 0x3bf1200/0x3bf1000 init 0x3bf1300. eth0: pcnet32 open after 5 ticks, init block 0x3bf1300 csr0 01f3. eth0: pcnet32_start_xmit() called, csr0 01f3. multimedia:~# ping -c5 192.168.1.1 PING 192.168.1.1 (192.168.1.1): 56 data bytes --- 192.168.1.1 ping statistics --- 5 packets transmitted, 0 packets received, 100% packet loss multimedia:~# arp -an ? (192.168.1.2) at <incomplete> on eth0 ? (192.168.1.1) at <incomplete> on eth0 multimedia:~# ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:00:E2:24:41:1D inet addr:192.168.1.51 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:9 Base address:0xfce0 Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 16:33 ` Danny ter Haar @ 2001-01-11 16:44 ` Hans Grobler 2001-01-12 11:50 ` PRoblem with pcnet32 under 2.4.0 , was :Drivers " Danny ter Haar 0 siblings, 1 reply; 31+ messages in thread From: Hans Grobler @ 2001-01-11 16:44 UTC (permalink / raw) To: Danny ter Haar; +Cc: linux-kernel Hi Danny, If you're willing, would you please follow "REPORTING-BUGS" and send some more info. Also cat /proc/interrupts. This one's intriging... -- Hans - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* PRoblem with pcnet32 under 2.4.0 , was :Drivers under 2.4 2001-01-11 16:44 ` Hans Grobler @ 2001-01-12 11:50 ` Danny ter Haar 2001-01-12 12:01 ` Hans Grobler 2001-01-12 22:33 ` Thomas Bogendoerfer 0 siblings, 2 replies; 31+ messages in thread From: Danny ter Haar @ 2001-01-12 11:50 UTC (permalink / raw) To: Hans Grobler; +Cc: linux-kernel According to Hans Grobler: > If you're willing, would you please follow "REPORTING-BUGS" and send some > more info. Also cat /proc/interrupts. This one's intriging... In short: Cyrix Multimedia box Everything onboard, including ethernet. Works as supposed to under 2.2.x (including 2.2.19pre7) installing 2.4.0 kernel recognises the driver but no byte is passed over the ethernet. Kernel: Linux version 2.4.0-ac7 (root@multimedia) (gcc version 2.95.3 20001229 (prerelea se)) #2 Fri Jan 12 11:17:47 CET 2001 Distribution: Debian unstable (sid) Output of loading the pcnet32 module: pcnet32_probe_pci: found device 0x001022.0x002000 ioaddr=0x00fce0 resource_flags=0x000101 PCI: Found IRQ 9 for device 00:0f.0 eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d pcnet32: pcnet32_private lp=c3c42000 lp_dma_addr=0x3c42000 assigned IRQ 9. pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de lspci -vx output: 00:0f.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet LANCE] ( rev 42) Subsystem: Advanced Micro Devices [AMD]: Unknown device 2000 Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at fce0 [size=32] Memory at fedffc00 (32-bit, non-prefetchable) [size=32] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [40] Power Management version 1 00: 22 10 00 20 07 00 90 02 42 00 00 02 00 40 00 00 10: e1 fc 00 00 00 fc df fe 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 00 20 30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 18 18 The machine is connected to a 3com 8ports 100Mbit hub no additional parameters when the module is loaded, except i tried debug=7 which gave verbose output After bootup this is the situation: multimedia:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:00:E2:24:41:1D inet addr:192.168.1.51 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:9 Base address:0xfce0 procinfo: multimedia:~# procinfo Linux 2.4.0-ac7 (root@multimedia) (gcc 2.95.3 20001229 ) #2 Fri Jan 12 11:17:47 CET 2001 1CPU [multimedia.(none)] Memory: Total Used Free Shared Buffers Cached Mem: 62308 12596 49712 0 636 6636 Swap: 184708 0 184708 Bootup: Fri Jan 12 12:30:22 2001 Load average: 0.02 0.03 0.01 1/28 229 user : 0:00:05.32 3.2% page in : 5744 nice : 0:00:00.00 0.0% page out: 354 system: 0:00:09.31 5.5% swap in : 1 idle : 0:02:33.77 91.3% swap out: 0 uptime: 0:02:48.38 context : 2940 irq 0: 16840 timer irq 9: 0 acpi, PCnet/FAST III irq 1: 3 keyboard irq 12: 0 PS/2 Mouse irq 2: 0 cascade [4] irq 14: 1640 ide0 irq 4: 127 serial irq 15: 3 ide1 irq 8: 1 rtc after trying to ping -c10 a host in it's own range (default gw in fact): Jan 12 12:30:36 multimedia kernel: eth0: pcnet32_open() irq 9 tx/rx rings 0x3c41 200/0x3c41000 init 0x3c41300. Jan 12 12:30:36 multimedia kernel: eth0: pcnet32 open after 5 ticks, init block 0x3c41300 csr0 01f3. Jan 12 12:30:38 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 01f3. Jan 12 12:33:38 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. Jan 12 12:33:50 multimedia last message repeated 12 times Jan 12 12:36:38 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. Jan 12 12:39:38 multimedia kernel: eth0: pcnet32_start_xmit() called, csr0 07f3. Jan 12 12:39:38 multimedia kernel: NETDEV WATCHDOG: eth0: transmit timed out Jan 12 12:39:38 multimedia kernel: eth0: transmit timed out, status 07f3, resett ing. Jan 12 12:39:38 multimedia kernel: Ring data dump: dirty_tx 0 cur_tx 16 (full) cur_rx 0. Jan 12 12:39:38 multimedia kernel: 03b1b012 0608 00000040 0310 03b1b812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b1a012 0608 00000040 0310 03b1a812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b19012 0608 00000040 0310 03b19812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b18012 0608 00000040 0310 03b18812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b03012 0608 00000040 0310 03b03812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b02012 0608 00000040 0310 03b02812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b01012 0608 00000040 0310 03b01812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b00012 0608 00000040 0310 03b00812 0608 0 0000092 0310 Jan 12 12:39:38 multimedia kernel: 03b0f012 0608 00000040 0310 03b0f812 0608 0 0000040 0310 Jan 12 12:39:38 multimedia kernel: 03b0e012 0608 00000040 0310 03b0e812 0608 0 0000040 0310 I send an email to the author, no response yet. Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: PRoblem with pcnet32 under 2.4.0 , was :Drivers under 2.4 2001-01-12 11:50 ` PRoblem with pcnet32 under 2.4.0 , was :Drivers " Danny ter Haar @ 2001-01-12 12:01 ` Hans Grobler 2001-01-12 12:16 ` Danny ter Haar 2001-01-12 22:33 ` Thomas Bogendoerfer 1 sibling, 1 reply; 31+ messages in thread From: Hans Grobler @ 2001-01-12 12:01 UTC (permalink / raw) To: Danny ter Haar; +Cc: linux-kernel On Fri, 12 Jan 2001, Danny ter Haar wrote: > According to Hans Grobler: > > If you're willing, would you please follow "REPORTING-BUGS" and send some > > more info. Also cat /proc/interrupts. This one's intriging... Thanks for the report (still studying it). > lspci -vx output: > > 00:0f.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet LANCE] ( What about the other devices? > irq 0: 16840 timer irq 9: 0 acpi, PCnet/FAST III Ok, this may not mean much, but have you tried compiling without acpi? Just to remove some variables... -- Hans - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: PRoblem with pcnet32 under 2.4.0 , was :Drivers under 2.4 2001-01-12 12:01 ` Hans Grobler @ 2001-01-12 12:16 ` Danny ter Haar 0 siblings, 0 replies; 31+ messages in thread From: Danny ter Haar @ 2001-01-12 12:16 UTC (permalink / raw) To: linux-kernel Hans Grobler <grobh@sun.ac.za> wrote: >> lspci -vx output: >What about the other devices? ok, here's the full listing : 00:00.0 Host bridge: Cyrix Corporation PCI Master Flags: bus master, medium devsel, latency 0 00: 78 10 01 00 07 00 80 02 00 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0e.0 VGA compatible controller: Intergraphics Systems CyberPro 5000 (rev 02) (prog-if 00 [VGA]) Subsystem: Unknown device 0280:7000 Flags: medium devsel, IRQ 11 Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Expansion ROM at <unassigned> [disabled] [size=64K] 00: ea 10 00 50 03 00 00 02 02 00 00 03 04 40 00 00 10: 00 00 00 fd 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 80 02 00 70 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00 00:0f.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet LANCE] ( rev 42) Subsystem: Advanced Micro Devices [AMD]: Unknown device 2000 Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at fce0 [size=32] Memory at fedffc00 (32-bit, non-prefetchable) [size=32] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [40] Power Management version 1 00: 22 10 00 20 07 00 90 02 42 00 00 02 00 40 00 00 10: e1 fc 00 00 00 fc df fe 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 00 20 30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 18 18 00:12.1 Bridge: Cyrix Corporation 5530 SMI [Kahlua] Flags: medium devsel Memory at 40012000 (32-bit, non-prefetchable) [size=256] 00: 78 10 01 01 02 00 80 02 00 00 80 06 00 00 00 00 10: 00 20 01 40 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.2 IDE interface: Cyrix Corporation 5530 IDE [Kahlua] (prog-if 00 []) Flags: medium devsel I/O ports at fc00 [size=16] 00: 78 10 02 01 01 00 80 02 00 00 01 01 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:12.3 Multimedia audio controller: Cyrix Corporation 5530 Audio [Kahlua] Flags: bus master, medium devsel, latency 0 Memory at 40011000 (32-bit, non-prefetchable) [size=128] 00: 78 10 03 01 06 00 80 02 00 00 01 04 00 00 00 00 10: 00 10 01 40 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:13.0 USB Controller: Compaq Computer Corporation: Unknown device a0f8 (rev 06 ) (prog-if 10 [OHCI]) Subsystem: Compaq Computer Corporation: Unknown device a0f8 Flags: medium devsel, IRQ 10 Memory at fedfe000 (32-bit, non-prefetchable) [size=4K] 00: 11 0e f8 a0 13 00 80 02 06 10 03 0c 00 40 00 00 10: 00 e0 df fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e f8 a0 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 50 00:14.0 Multimedia video controller: Zoran Corporation ZR36120 (rev 03) Subsystem: Optibase Ltd: Unknown device 5000 Flags: fast devsel, IRQ 10 Memory at fedfd000 (32-bit, non-prefetchable) [size=4K] 00: de 11 20 61 02 00 00 00 03 00 00 04 00 40 00 00 10: 00 d0 df fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 55 12 00 50 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 02 10 The last one is an plugin pci mpeg2 decoder (which is optional) >> irq 0: 16840 timer irq 9: 0 acpi, PCnet/FAST III > >Ok, this may not mean much, but have you tried compiling without acpi? >Just to remove some variables... yesterdays trials were with 2.4.0-ac4 which did not include acpi. Wil re-compile (slow!! :) wihout acpi and re-try. Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: PRoblem with pcnet32 under 2.4.0 , was :Drivers under 2.4 2001-01-12 11:50 ` PRoblem with pcnet32 under 2.4.0 , was :Drivers " Danny ter Haar 2001-01-12 12:01 ` Hans Grobler @ 2001-01-12 22:33 ` Thomas Bogendoerfer 2001-01-15 16:29 ` Danny ter Haar 1 sibling, 1 reply; 31+ messages in thread From: Thomas Bogendoerfer @ 2001-01-12 22:33 UTC (permalink / raw) To: Danny ter Haar; +Cc: Hans Grobler, linux-kernel On Fri, Jan 12, 2001 at 12:50:10PM +0100, Danny ter Haar wrote: > eth0: PCnet/FAST III 79C973 at 0xfce0, 00 00 e2 24 41 1d > pcnet32: pcnet32_private lp=c3c42000 lp_dma_addr=0x3c42000 assigned IRQ 9. > pcnet32.c:v1.25kf 26.9.1999 tsbogend@alpha.franken.de same chip works for me von my P5 SMP box. > irq 0: 16840 timer irq 9: 0 acpi, PCnet/FAST III no interrupts for PCnet driver sounds more like interrupt routing problem to me. Thomas. -- Crap can work. Given enough thrust pigs will fly, but it's not necessary a good idea. [ Alexander Viro on linux-kernel ] - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: PRoblem with pcnet32 under 2.4.0 , was :Drivers under 2.4 2001-01-12 22:33 ` Thomas Bogendoerfer @ 2001-01-15 16:29 ` Danny ter Haar 0 siblings, 0 replies; 31+ messages in thread From: Danny ter Haar @ 2001-01-15 16:29 UTC (permalink / raw) To: Thomas Bogendoerfer; +Cc: Hans Grobler, linux-kernel I experimented some further today. using some printk i found out is was setting Fullduplex, hardcoded that to half-duplex (mine is connected to a hub and not a switch) , and it's configuration was 100Mbit as it was supposed to. Then i started looking at the start_xmit code and got lost :-))) Hope this helpes to pin-point the problem. Danny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Drivers under 2.4 2001-01-11 10:24 ` Danny ter Haar 2001-01-11 10:31 ` Andi Kleen @ 2001-01-11 12:56 ` Alan Cox 1 sibling, 0 replies; 31+ messages in thread From: Alan Cox @ 2001-01-11 12:56 UTC (permalink / raw) To: dth; +Cc: linux-kernel > cyrix processor, chipset and amd/lance ethernet chipset onboard. > It' working fine with 2.2.x but not with 2.4.x kernels with > the same driver version of the pcnet32 networkdriver. What problems do you see - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2. 2001-01-09 9:12 Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Silviu Marin-Caea 2001-01-09 10:17 ` Alessandro Suardi @ 2001-01-09 10:28 ` Alan Cox 2001-01-09 16:10 ` [rlug] " Eugen 2001-01-09 19:01 ` J Sloan 3 siblings, 0 replies; 31+ messages in thread From: Alan Cox @ 2001-01-09 10:28 UTC (permalink / raw) To: Silviu Marin-Caea; +Cc: linux-kernel, rlug > I have RedHat7, glibc-2.2-9, gcc-2.96-69. Ditto > If I try to rebuild 2.4.0 while running the new kernel, I get random > compiler errors. Now I don't. What hardware are you using ? > It happens on two machines. One of them runs 2.4.0-test12, the other > 2.4.0. Both of them with the updates above mentioned. What hardware what errors ? > I know this is a RedHat issue, but it may be useful to know for some. It may well be compiler optimisation where the new gcc is optimising out something someone forgot in a driver or miscompiling a specific driver. One good way to test if its compiler or kernel triggered would be to rebuild 2.4.0 with egcs (aka kgcc). I'd like to know what drivers you are running so I can try and duplicate it - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: [rlug] Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2. 2001-01-09 9:12 Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Silviu Marin-Caea 2001-01-09 10:17 ` Alessandro Suardi 2001-01-09 10:28 ` Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Alan Cox @ 2001-01-09 16:10 ` Eugen 2001-01-09 19:01 ` J Sloan 3 siblings, 0 replies; 31+ messages in thread From: Eugen @ 2001-01-09 16:10 UTC (permalink / raw) To: rlug; +Cc: linux-kernel io am compilat 2.4.0 in timp ce rulam 2.4.0-test12 si a mers > > I can build 2.4.0 while running kernel 2.2.16. > > If I try to rebuild 2.4.0 while running the new kernel, I get random > compiler errors. > > It happens on two machines. One of them runs 2.4.0-test12, the other > 2.4.0. Both of them with the updates above mentioned. > > I know this is a RedHat issue, but it may be useful to know for some. > > -- > Systems and Network Administrator - Delta Romania > Phone +4093-267961 > > --- > Send e-mail to 'listar@lug.ro' with 'unsubscribe rlug' to > unsubscribe from this list. > Eugen - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
* Re: Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2. 2001-01-09 9:12 Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Silviu Marin-Caea ` (2 preceding siblings ...) 2001-01-09 16:10 ` [rlug] " Eugen @ 2001-01-09 19:01 ` J Sloan 3 siblings, 0 replies; 31+ messages in thread From: J Sloan @ 2001-01-09 19:01 UTC (permalink / raw) To: Silviu Marin-Caea; +Cc: linux-kernel, rlug Silviu Marin-Caea wrote: > I have RedHat7, glibc-2.2-9, gcc-2.96-69. > > I can build 2.4.0 while running kernel 2.2.16. > > If I try to rebuild 2.4.0 while running the new kernel, I get random > compiler errors. Could you supply the text of the errors, and your .config? I've been building 2.4.0 kernels on Red Hat 7 with no problems on the following systems - - Celeron 600 - AMD K6-2 450 - Quad Pentium Pro jjs - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 31+ messages in thread
end of thread, other threads:[~2001-01-15 16:29 UTC | newest] Thread overview: 31+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2001-01-09 9:12 Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Silviu Marin-Caea 2001-01-09 10:17 ` Alessandro Suardi 2001-01-09 10:33 ` Failure building 2.4 while running 2.4. Success in building 2.4 Alan Cox 2001-01-09 18:20 ` Failure building 2.4 while running 2.4. There is no such thing Silviu Marin-Caea 2001-01-09 18:43 ` Alan Cox 2001-01-09 19:57 ` Drivers under 2.4 Dennis 2001-01-09 20:13 ` suser checks in 2.2.x Bosko Radivojevic 2001-01-09 18:39 ` Arnaldo Carvalho de Melo 2001-01-10 18:22 ` Drivers under 2.4 Dennis 2001-01-10 20:01 ` Hans Grobler 2001-01-10 21:37 ` Dennis 2001-01-10 21:38 ` Andi Kleen 2001-01-10 22:08 ` Hans Grobler 2001-01-11 10:24 ` Danny ter Haar 2001-01-11 10:31 ` Andi Kleen 2001-01-11 10:58 ` Danny ter Haar 2001-01-11 11:36 ` Andrew Morton 2001-01-11 11:58 ` Danny ter Haar 2001-01-11 14:00 ` Danny ter Haar 2001-01-11 14:32 ` Jeff Garzik 2001-01-11 16:33 ` Danny ter Haar 2001-01-11 16:44 ` Hans Grobler 2001-01-12 11:50 ` PRoblem with pcnet32 under 2.4.0 , was :Drivers " Danny ter Haar 2001-01-12 12:01 ` Hans Grobler 2001-01-12 12:16 ` Danny ter Haar 2001-01-12 22:33 ` Thomas Bogendoerfer 2001-01-15 16:29 ` Danny ter Haar 2001-01-11 12:56 ` Drivers " Alan Cox 2001-01-09 10:28 ` Failure building 2.4 while running 2.4. Success in building 2.4 while running 2.2 Alan Cox 2001-01-09 16:10 ` [rlug] " Eugen 2001-01-09 19:01 ` J Sloan
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox