From: "Bryan W. Headley" <bheadley@interaccess.com>
To: linux-kernel@vger.kernel.org
Subject: 2.4.2-pre1 won't boot on my SMP P-II
Date: Sun, 04 Feb 2001 18:08:00 -0600 [thread overview]
Message-ID: <3A7DEEE0.6B2B5AE3@interaccess.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 377 bytes --]
Last kernel that booted was Redhat's build of 2.4.0-pre11. I'm not sure
where the issue is at, so I attach a log of the system booting up.
It's an ASUS P2B-DS with dual Deschutes PII-450s.
Anybody with a clue as to where to look, please advise. (Have other boot
logs)
--
____ .:. ____
Bryan W. Headley - bheadley@interaccess.com
[-- Attachment #2: bootup-2.4.2-pre1.log --]
[-- Type: application/octet-stream, Size: 10299 bytes --]
Linux version 2.4.2-pre1 (bheadley@cactus.bheadley.org) (gcc version 2.96 20000731 (Red Hat Linux 7.0)) #1 SMP Sun Feb 4 15:57:05 CST 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009f400 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000c00 @ 000000000009f400 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 000000000fefd000 @ 0000000000100000 (usable)
BIOS-e820: 0000000000002000 @ 000000000fffd000 (ACPI data)
BIOS-e820: 0000000000001000 @ 000000000ffff000 (ACPI NVS)
BIOS-e820: 0000000000001000 @ 00000000fec00000 (reserved)
BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000f6df0
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 65533
zone(0): 4096 pages.
zone(1): 61437 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
SEP present.
MTRR present.
PGE present.
MCA present.
CMOV present.
PAT present.
PSE present.
MMX present.
FXSR present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 05, APIC ID 2, APIC INT 05
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 0, trig 0, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 09, APIC ID 2, APIC INT 09
Int: type 0, pol 0, trig 0, bus 2, IRQ 0c, APIC ID 2, APIC INT 0c
Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 0, IRQ 13, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 24, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 30, APIC ID 2, APIC INT 10
Lint: type 3, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 1, trig 1, bus 2, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Kernel command line: BOOT_IMAGE=linux-2.4.2pre1 ro root=801 BOOT_FILE=/boot/vmlinuz-2.4.2-pre1 console=ttyS0
Initializing CPU#0
Detected 451.032 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 897.84 BogoMIPS
Memory: 254704k/262132k available (1253k kernel code, 7040k reserved, 457k data, 252k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.37 (20001109) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU0: Intel Pentium II (Deschutes) stepping 02
per-CPU timeslice cutoff: 1461.42 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 1000000
Getting ID: e000000
Getting LVT0: 8700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 3
Booting processor 1/0 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Initializing CPU#1
Startup point 1.
CPU#1 (phys ID: 0) waiting for CALLOUT
Waiting for send to finish...
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 901.12 BogoMIPS
Stack at about cfff5fb8
CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check reporting enabled on CPU#1.
CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
OK.
CPU1: Intel Pentium II (Deschutes) stepping 02
CPU has booted.
Before bogomips.
Total of 2 processors activated (1798.96 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
..TIMER: vector=49 pin1=2 pin2=0
activating NMI Watchdog ... done.
testing the IO APIC.......................
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 451.0544 MHz.
..... host bus clock speed is 100.2340 MHz.
cpu: 0, clocks: 1002340, slice: 334113
CPU0<T0:1002336,T1:668208,D:15,S:334113,C:1002340>
cpu: 1, clocks: 1002340, slice: 334113
CPU1<T0:1002336,T1:334096,D:14,S:334113,C:1002340>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
PCI: PCI BIOS revision 2.10 entry at 0xf0770, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
PCI->APIC IRQ transform: (B0,I4,P3) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 16
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Limiting direct PCI/PCI transfers.
isapnp: Scanning for Pnp cards...
isapnp: SB audio device quirk - increasing port range
isapnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB AWE64 PnP'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
DMI 2.0 present.
33 structures occupying 1080 bytes.
DMI table at 0x000F59FA.
BIOS Vendor: Award Software, Inc.
BIOS Version: ASUS P2B-D ACPI BIOS Revision 1006
BIOS Release: 09/15/98
System Vendor: System Manufacturer.
Product Name: System Name.
Version System Version.
Serial Number SYS-1234567890.
Board Vendor: ASUSTeK Computer INC..
Board Name: P2B-DS.
Board Version: REV 1.xx.
Asset Tag: Asset-1234567890.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
apm: disabled - APM is not SMP safe.
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169184kB/56394kB, 512 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 332k freed
Serial driver version 5.02 (2000-08-09) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
atp.c:v1.09 8/9/2000 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/atp.html
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
ACPI: Core Subsystem version [20010125]
LNMI Watchdog detected LOCKUP on CPU0, registers:
CPU: 0
EIP: 0010:[<c02345dd>]
EFLAGS: 00000086
eax: 00000000 ebx: 000f8040 ecx: 00000001 edx: c0272b42
esi: cfd6ff70 edi: cfd6e331 ebp: 00000000 esp: cfd6ff48
ds: 0018 es: 0018 ss: 0018
Process kacpid (pid: 7, stackpage=cfd6f000)
Stack: 00000286 00070000 00c70000 c01c10c1 000f8040 cfd6ff70 cfd6e331 00000000
c01d47fa c0272b42 0000003c cfd6ffa0 000f8040 00000000 00000000 00000000
00000000 00000000 cfd6e000 00000000 00000001 cfd6e000 20010125 00000003
Call Trace: [<c01c10c1>] [<c01d47fa>] [<c0105000>] [<c0108626>] [<c01d46d0>]
Code: 80 3d 20 50 29 c0 00 f3 90 7e f5 e9 93 5c ee ff 80 3d 20 50
console shuts up ...
next reply other threads:[~2001-02-04 23:58 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-02-05 0:08 Bryan W. Headley [this message]
-- strict thread matches above, loose matches on Subject: below --
2001-02-05 2:54 2.4.2-pre1 won't boot on my SMP P-II Mikael Pettersson
2001-02-05 3:15 ` Bryan W. Headley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3A7DEEE0.6B2B5AE3@interaccess.com \
--to=bheadley@interaccess.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox