From: Jussi Laako <jlaako@pp.htv.fi>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Vojtech Pavlik <vojtech@suse.cz>, linux-kernel@vger.kernel.org
Subject: Re: VIA/PDC/Athlon
Date: Thu, 17 May 2001 23:28:49 +0300 [thread overview]
Message-ID: <3B043481.A394D98D@pp.htv.fi> (raw)
In-Reply-To: <E150QtB-0005aC-00@the-village.bc.nu>
Alan Cox wrote:
>
> RH 2.4.2-2 and 2.4.4-ac9 are I believe the same driver exactly. 2.4.3 is
> an ancient known not to work well driver
Ummm... Here's stripped dmesg of both kernels... Is this compiler thingie or
Athlon optimizations?
Notice also different detected PDC20265 BIOS settings! So 2.4.4-ac9 detects
those BIOS settings correctly and 2.4.2-2 doesn't. That's probably reason
why 2.4.2-2 works?
--- 8< ---
Linux version 2.4.4-ac9 (root@davinci) (gcc version 2.95.3 20010315
(release)) #1 Wed May 16 17:37:30 EEST 2001
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
PDC20265: IDE controller on PCI bus 00 dev 88
PCI: Found IRQ 10 for device 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x7400-0x7407, BIOS settings: hde:DMA, hdf:DMA
ide3: BM-DMA at 0x7408-0x740f, BIOS settings: hdg:DMA, hdh:DMA
hda: IBM-DTLA-307030, ATA DISK drive
hdb: SONY CDU4811, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
hdf: IBM-DTLA-307030, ATA DISK drive
hdg: IBM-DTLA-307030, ATA DISK drive
hdh: IBM-DTLA-307030, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x8800-0x8807,0x8402 on irq 10
ide3 at 0x8000-0x8007,0x7802 on irq 10
hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, UDMA(100)
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdf: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdg: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdh: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
Partition check:
hda:hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda1 hda2 hda3 hda4
hde: hde1 hde2 hde3 hde4
hdf: unknown partition table
hdg: unknown partition table
hdh: unknown partition table
--- 8< ---
Linux version 2.4.2-2 (root@porky.devel.redhat.com) (gcc version 2.96
20000731 (Red Hat Linux 7.1 2.96-79)) #1 Sun Apr 8 20:41:30 EDT 2001
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
PDC20265: IDE controller on PCI bus 00 dev 88
PCI: Found IRQ 10 for device 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x7400-0x7407, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0x7408-0x740f, BIOS settings: hdg:pio, hdh:pio
hda: IBM-DTLA-307030, ATA DISK drive
hdb: SONY CDU4811, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
hdf: IBM-DTLA-307030, ATA DISK drive
hdg: IBM-DTLA-307030, ATA DISK drive
hdh: IBM-DTLA-307030, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x8800-0x8807,0x8402 on irq 10
ide3 at 0x8000-0x8007,0x7802 on irq 10
hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, UDMA(33)
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdf: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdg: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdh: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3 hda4
hde: hde1 hde2 hde3 hde4
hdf: unknown partition table
hdg: unknown partition table
hdh: unknown partition table
--- 8< ---
- Jussi Laako
--
PGP key fingerprint: 161D 6FED 6A92 39E2 EB5B 39DD A4DE 63EB C216 1E4B
Available at PGP keyservers
next prev parent reply other threads:[~2001-05-17 20:30 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-05-16 17:25 VIA/PDC/Athlon Jussi Laako
2001-05-16 20:05 ` VIA/PDC/Athlon Vojtech Pavlik
2001-05-17 16:43 ` VIA/PDC/Athlon Jussi Laako
2001-05-17 16:44 ` VIA/PDC/Athlon Alan Cox
2001-05-17 20:28 ` Jussi Laako [this message]
2001-05-17 21:25 ` VIA/PDC/Athlon Alan Cox
2001-05-19 12:05 ` VIA/PDC/Athlon - IDE error theory Wilfried Weissmann
2001-05-19 12:17 ` Jussi Laako
2001-05-16 23:47 ` VIA/PDC/Athlon Alan Cox
2001-05-17 0:19 ` VIA/PDC/Athlon Zilvinas Valinskas
2001-05-17 16:46 ` VIA/PDC/Athlon Jussi Laako
-- strict thread matches above, loose matches on Subject: below --
2001-05-18 3:52 VIA/PDC/Athlon Pavel Roskin
2001-05-18 6:33 ` VIA/PDC/Athlon Steffen Persvold
2001-05-18 12:15 ` VIA/PDC/Athlon Pavel Roskin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B043481.A394D98D@pp.htv.fi \
--to=jlaako@pp.htv.fi \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=vojtech@suse.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox