From: Anders Peter Fugmann <afu@fugmann.dhs.org>
To: Jeff Hartmann <jhartmann@valinux.com>
Cc: "Paul G. Allen" <pgallen@randomlogic.com>, linux-kernel@vger.kernel.org
Subject: Re: AMD-760 AGP Support
Date: Tue, 31 Jul 2001 04:48:16 +0200 [thread overview]
Message-ID: <3B661C70.2010303@fugmann.dhs.org> (raw)
In-Reply-To: <3B5CDFC1.4D954891@randomlogic.com> <3B5D9799.70807@valinux.com>
[-- Attachment #1: Type: text/plain, Size: 878 bytes --]
I do not know if you still want reports,
but here is one anyway:-)
I've just bought an ASUS A7M266, and
agpgart is working perfectly with my Gforce256, using the
'agp_try_unsupported=1' option
The kernel is 2.4.7-ac3.
Output from lspci -vvv is attached.
Regards
Anders Fugmann
Jeff Hartmann wrote:
>
> I have a pre production Tyan mb that I tested things on. It seemed to
> work just fine with agp_try_unsupported=1. Please test it with
> agp_try_unsupported on an actual production system to make sure, but if
> it works just send me the output of lspci -vvv and I'll put it in the
> kernel.
>
> -Jeff
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
[-- Attachment #2: lspci.out --]
[-- Type: text/plain, Size: 6177 bytes --]
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700e (rev 13)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at df800000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at e000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP+ 64bit- FW+ Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700f (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: ce000000-cfdfffff
Prefetchable memory behind bridge: cff00000-df7fffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 8040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.4 Non-VGA unclassified device: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 8040
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 80e2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a000 [size=128]
Region 1: Memory at cd800000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller: nVidia Corporation GeForce 256 (rev 10) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc. AGP-V6600 SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at cfff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=15 SBA- AGP+ 64bit- FW+ Rate=<none>
next prev parent reply other threads:[~2001-07-30 20:45 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-07-24 2:38 AMD-760 MP AGP Support Paul G. Allen
2001-07-24 15:43 ` Jeff Hartmann
2001-07-25 1:47 ` Gregory T. Norris
2001-07-31 2:48 ` Anders Peter Fugmann [this message]
2001-07-30 22:43 ` AMD-760 " Paul G. Allen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B661C70.2010303@fugmann.dhs.org \
--to=afu@fugmann.dhs.org \
--cc=jhartmann@valinux.com \
--cc=linux-kernel@vger.kernel.org \
--cc=pgallen@randomlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox