From: "Bobby D. Bryant" <bdbryant@mail.utexas.edu>
To: linux-kernel@vger.kernel.org
Cc: Mike Frisch <mfrisch@saturn.tlug.org>
Subject: Re: "clock timer configuration lost" on ASUS A7A266
Date: Thu, 02 Aug 2001 21:34:40 +0600 [thread overview]
Message-ID: <3B697310.EF44BCDB@mail.utexas.edu> (raw)
In-Reply-To: <20010802152921.A6242@saturn.tlug.org>
[-- Attachment #1: Type: text/plain, Size: 418 bytes --]
Mike Frisch wrote:
> Hardware: ASUS A7A266 (ALiMAGiK chipset), AMD T-Bird 1.2 GHz
> Kernel: 2.4.7-ac2
>
> 'dmesg' frequently reports:
>
> probable hardware bug: clock timer configuration lost - probably a VIA686a motherboard.
> probable hardware bug: restoring chip configuration.
Just FYI, I see the same thing on the same board. My lspci -vv is also attached. Ask if
you need more.
Bobby Bryant
Austin, Texas
[-- Attachment #2: temp.txt --]
[-- Type: text/plain, Size: 5708 bytes --]
00:00.0 Host bridge: Acer Laboratories Inc. [ALi]: Unknown device 1647 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [b0] AGP version 2.0
Status: RQ=27 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc800000-dddfffff
Prefetchable memory behind bridge: ddf00000-dfffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:04.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if fa)
Subsystem: Asustek Computer, Inc.: Unknown device 8053
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at d400 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at da000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 4d33
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b400 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a400 [size=4]
Region 4: I/O ports at a000 [size=64]
Region 5: Memory at d9800000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550])
Subsystem: US Robotics/3Com: Unknown device 00d7
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 9800 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 82) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc.: Unknown device 0641
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at de000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at dc800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at ddfe0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
prev parent reply other threads:[~2001-08-03 3:38 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-08-02 19:29 "clock timer configuration lost" on ASUS A7A266 Mike Frisch
2001-08-02 15:34 ` Bobby D. Bryant [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B697310.EF44BCDB@mail.utexas.edu \
--to=bdbryant@mail.utexas.edu \
--cc=linux-kernel@vger.kernel.org \
--cc=mfrisch@saturn.tlug.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox