[PATCH] eepro100.c - Add option to disable power saving in 2.4.7-ac7

Martin Knoblauch
2001-08-06T15:48:27Z

[-- Attachment #1: Type: text/plain, Size: 701 bytes --]

Hi,

after realizing that my first attempt for this patch was to
enthusiastic, I have no a somewhat stripped down version. Compiles
against 2.4.7-ac7.

The patch adds the option "power_save" to eepro100. If "1" (default),
power save handling is done as normal. If "0", no power saving is done.
This is to workaround some flaky eepro100 adapters that do not survive
D0->D2-D0 transitions.

Martin
--
------------------------------------------------------------------
Martin Knoblauch | email: Martin.Knoblauch@TeraPort.de
TeraPort GmbH | Phone: +49-89-510857-309
C+ITS | Fax: +49-89-510857-111
http://www.teraport.de | Mobile: +49-170-4904759

[-- Attachment #2: eepro100-power_save.txt --]
[-- Type: text/plain, Size: 3246 bytes --]

--- linux-2.4.7-ac7/drivers/net/eepro100.c-orig-ac7 Mon Aug 6 10:36:54 2001
+++ linux-2.4.7-ac7/drivers/net/eepro100.c Mon Aug 6 17:32:38 2001
@@ -60,6 +60,8 @@
static int full_duplex[] = {-1, -1, -1, -1, -1, -1, -1, -1};
static int options[] = {-1, -1, -1, -1, -1, -1, -1, -1};
static int debug = -1; /* The debug level */
+/* power_save option */
+static int power_save = 1;

/* A few values that may be tweaked. */
/* The ring sizes should be a power of two for efficiency. */
@@ -125,6 +127,7 @@
MODULE_PARM(rx_copybreak, "i");
MODULE_PARM(max_interrupt_work, "i");
MODULE_PARM(multicast_filter_limit, "i");
+MODULE_PARM(power_save, "i");
MODULE_PARM_DESC(debug, "eepro100 debug level (0-6)");
MODULE_PARM_DESC(options, "eepro100: Bits 0-3: tranceiver type, bit 4: full duplex, bit 5: 100Mbps");
MODULE_PARM_DESC(full_duplex, "eepro100 full duplex setting(s) (1)");
@@ -136,6 +139,7 @@
MODULE_PARM_DESC(rx_copybreak, "eepro100 copy breakpoint for copy-only-tiny-frames");
MODULE_PARM_DESC(max_interrupt_work, "eepro100 maximum events handled per interrupt");
MODULE_PARM_DESC(multicast_filter_limit, "eepro100 maximum number of filtered multicast addresses");
+MODULE_PARM_DESC(power_save, "Disable/Enable power saving (0,1). Default 1.");

#define RUN_AT(x) (jiffies + (x))

@@ -778,7 +782,11 @@
udelay(10);

/* Put chip into power state D2 until we open() it. */
- pci_set_power_state(pdev, 2);
+ if ((power_save < 0) || (power_save > 1))
+ power_save = 1;
+ printk(KERN_INFO " power_save = %d.\n",power_save);
+ if (power_save)
+ pci_set_power_state(pdev, 2);

pci_set_drvdata (pdev, dev);

@@ -902,7 +910,8 @@

MOD_INC_USE_COUNT;

- pci_set_power_state(sp->pdev, 0);
+ if (power_save)
+ pci_set_power_state(sp->pdev, 0);

/* Set up the Tx queue early.. */
sp->cur_tx = 0;
@@ -1833,7 +1842,8 @@
if (speedo_debug > 0)
printk(KERN_DEBUG "%s: %d multicast blocks dropped.\n", dev->name, i);

- pci_set_power_state(sp->pdev, 2);
+ if (power_save)
+ pci_set_power_state(sp->pdev, 2);

MOD_DEC_USE_COUNT;

@@ -1902,12 +1912,14 @@
They are currently serialized only with MDIO access from the
timer routine. 2000/05/09 SAW */
saved_acpi = sp->pdev->current_state;
- pci_set_power_state(sp->pdev, 0);
+ if (power_save)
+ pci_set_power_state(sp->pdev, 0);
t = del_timer_sync(&sp->timer);
data->val_out = mdio_read(ioaddr, data->phy_id & 0x1f, data->reg_num & 0x1f);
if (t)
add_timer(&sp->timer); /* may be set to the past --SAW */
- pci_set_power_state(sp->pdev, saved_acpi);
+ if (power_save)
+ pci_set_power_state(sp->pdev, saved_acpi);
return 0;

case SIOCSMIIREG: /* Write MII PHY register. */
@@ -1915,12 +1927,14 @@
if (!capable(CAP_NET_ADMIN))
return -EPERM;
saved_acpi = sp->pdev->current_state;
- pci_set_power_state(sp->pdev, 0);
+ if (power_save)
+ pci_set_power_state(sp->pdev, 0);
t = del_timer_sync(&sp->timer);
mdio_write(ioaddr, data->phy_id, data->reg_num, data->val_in);
if (t)
add_timer(&sp->timer); /* may be set to the past --SAW */
- pci_set_power_state(sp->pdev, saved_acpi);
+ if (power_save)
+ pci_set_power_state(sp->pdev, saved_acpi);
return 0;
default:
return -EOPNOTSUPP;