From: Brian Strand <bstrand@switchmanagement.com>
To: linux-kernel@vger.kernel.org
Subject: Re: 3ware: no cards found in 2.2.19, cards found in 2.4.x
Date: Sat, 25 Aug 2001 04:56:03 -0700 [thread overview]
Message-ID: <3B879253.2010400@switchmanagement.com> (raw)
In-Reply-To: <E15aKzT-0006BX-00@the-village.bc.nu>
Alan Cox wrote:
>Im using one with 2.2.18 fine. Is your bios set for pnp os ?
>
>
I modified the setting from "No PNP OS" to "PNP OS", with identical
results (card not found). Could there be a conflict with another card
only under 2.2.19? Here is an lspci -vvv (from the 2.4.4-14 kernel):
00:07.0 RAID bus controller: 3ware Inc 3ware ATA-RAID (rev 12)
Subsystem: 3ware Inc 3ware ATA-RAID
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2250ns min)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 2420 [size=16]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:08.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c810 (rev 23)
Subsystem: Symbios Logic Inc. (formerly NCR) 8100S
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 58
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at d0001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 VGA compatible controller: Cirrus Logic GD 5480 (rev 23)
(prog-if 00 [VGA])
Subsystem: Unknown device 3e3e:003e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 2500ns max)
Region 0: Memory at d2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=32K]
00:0b.0 PIC: Intel Corporation 683053 Programmable Interrupt Device
(prog-if 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (2000ns min, 2000ns max)
00:0c.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0c.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 2430 [size=16]
00:0c.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 54
Region 4: I/O ports at 2400 [size=32]
00:0c.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:10.0 Host bridge: Intel Corporation 450NX - 82451NX Memory & I/O
Controller (rev 03)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:12.0 Host bridge: Intel Corporation 450NX - 82454NX/84460GX PCI
Expander Bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 128, cache line size 08
00:13.0 Host bridge: Intel Corporation 450NX - 82454NX/84460GX PCI
Expander Bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 128, cache line size 08
01:01.0 SCSI storage controller: Adaptec AHA-2940U2/W
Subsystem: Adaptec: Unknown device a180
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (9750ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
BIST result: 00
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at d4004000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:02.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 02)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, cache line size 08
Bus: primary=01, secondary=02, subordinate=02, sec-latency=68
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d4100000-d43fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000eff00000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
01:03.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c896 (rev 01)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 57
Region 0: I/O ports at 3400 [size=256]
Region 1: Memory at d4005000 (64-bit, non-prefetchable) [size=1K]
Region 3: Memory at d4000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:03.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR)
53c896 (rev 01)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin B routed to IRQ 56
Region 0: I/O ports at 3800 [size=256]
Region 1: Memory at d4005400 (64-bit, non-prefetchable) [size=1K]
Region 3: Memory at d4002000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
(rev 64)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 3c00 [size=128]
Region 1: Memory at d4005800 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 Memory controller: Distributed Processing Technology Domino RAID
Engine (rev 02)
Subsystem: Distributed Processing Technology Domino RAID Engine
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B+
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 50
BIST result: 00
Region 0: Memory at d4100000 (32-bit, non-prefetchable) [size=64K]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
02:04.0 I2O: Distributed Processing Technology SmartRAID V Controller
(rev 03) (prog-if 01)
Subsystem: Distributed Processing Technology: Unknown device 50c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (250ns min, 250ns max), cache line size 08
Interrupt: pin A routed to IRQ 20
BIST result: 00
Region 0: Memory at d4200000 (32-bit, non-prefetchable) [size=2M]
Region 1: I/O ports at 4000 [size=256]
Expansion ROM at 00090000 [disabled] [size=32K]
next parent reply other threads:[~2001-08-25 11:56 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <E15aKzT-0006BX-00@the-village.bc.nu>
2001-08-25 11:56 ` Brian Strand [this message]
2001-08-24 5:36 3ware: no cards found in 2.2.19, cards found in 2.4.x Brian Strand
2001-08-24 7:01 ` David Ford
2001-08-24 16:10 ` Brian Strand
2001-08-24 16:34 ` David Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B879253.2010400@switchmanagement.com \
--to=bstrand@switchmanagement.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox