Confirmation!

Confirmation!

[Napanda. C. Pemmaiah]

Hello,
       How are you? I am Anup Pemmaiah doing my masters in computer science at 
Utah State University -USA. I have a linux box running Red Hat 7.2 (kernel 
version 2.4). My ethernet driver is 3c59x. I had two questions regarding 3c59x 
module installation.

1)  When the system is booted the module gets installed. I was curious from 
where does this installation takes place. As far i learnt from the 
documentation, this is done because of the entry "alias eth0 3c59x" in the 
/etc/modules.conf file. But even if I delete this entry and reboot the system 
still the module gets installed.

2)          I removed the module by "rmmod 3c59x" and again installed it by 
"insmod /lib/modules/...../net/3c59x.o". The module got installed but in the 
/proc/modules it shows "3c59x    0(unused)". And from /etc/rc.d/init.d if I 
start the network by saying "./network start" the eth0 conncetion does not 
come up. Is it because of some options setting to be done during insmod. I 
searched and tried a lot but I could not figure out the above two problems.

            It will be really great if you can give the solution for the above 
problems. I will be eagerly waiting for your reply. I am sorry for disturbing 
you. Have a nice day.

Thank you,
Anup Pemmaiah

-------------------------------------------------
N.C.Pemmaiah (Anup)
620E, 700N, Apt# 2
Logan, UT-84321,USA.
email: pemmaiah@cc.usu.edu, anup_pemmaiah@yahoo.com
Ph: 435-512-0935(mob.), 435-752-5976 (Res.)
-------------------------------------------------

Re: Confirmation!

[Hank Leininger]

On 2002-04-02, "Napanda. C. Pemmaiah" <pemmaiah@cc.usu.edu> wrote:

> 1)  When the system is booted the module gets installed. I was curious
> from where does this installation takes place. As far i learnt from the

This is going to be RedHat distribution specific; it's not a Linux kernel /
networking question.  The RedHat boot scripts take care of module loading,
etc.

> 2)          I removed the module by "rmmod 3c59x" and again installed
> it by "insmod /lib/modules/...../net/3c59x.o". The module got installed
> but in the /proc/modules it shows "3c59x    0(unused)". And from
> /etc/rc.d/init.d if I start the network by saying "./network start" the

This too is a RedHat-specific question.  If you 'insmod 3c59x; ifconfig
eth0 1.2.3.4 ...' by hand, it should surely work.  The /etc/rc.d/init.d
contents on your system are all created / set up by RedHat.

You should check out the redhat-list list, subscribe info at:
https://listman.redhat.com/mailman/listinfo/redhat-list

We also have a searchable archive of it at:
http://marc.theaimsgroup.com/?l=redhat-list&r=1&w=2

HTH,

Hank Leininger <hlein@progressive-comp.com> 
  

Confirmation!!!

[Mikhail Fridman]

-- 
Hello,

I Mikhail Fridman. has selected you specially as one of my 
beneficiaries
for my Charitable Donation, Just as I have declared on May 23, 2016 to 
give
my fortune as charity.

Check the link below for confirmation:

http://www.ibtimes.co.uk/russias-second-wealthiest-man-mikhail-fridman-plans-leaving-14-2bn-fortune-charity-1561604


Reply as soon as possible with further directives.

Best Regards,
Mikhail Fridman