IDE performance slowdown in 2.5

IDE performance slowdown in 2.5

[Nero]

With 2.5.47, I get 22mb/s using hdparm -t /dev/hda, and close to 40mb/s
when running 2.4.x
Is this at all expected?
Info from hdparm:

[13:19:08] root@debian:/proc# hdparm -v /dev/hda
/dev/hda:
   multcount    =  0 (off)
   IO_support   =  1 (32-bit)
   unmaskirq    =  1 (on)
   using_dma    =  1 (on)
   keepsettings =  0 (off)
   readonly     =  0 (off)
   readahead    = 256 (on)
   geometry     = 50765/16/63, sectors = 117231408, start = 0


[13:18:51] root@debian:/proc# hdparm -i /dev/hda
/dev/hda:

   Model=ST360021A, FwRev=3.05, SerialNo=3HR01F5W
   Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
   RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
   BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
   CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=117231408
   IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
   PIO modes:  pio0 pio1 pio2 pio3 pio4
   DMA modes:  mdma0 mdma1 mdma2
   UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
   AdvancedPM=no WriteCache=enabled
   Drive conforms to: device does not report version:  1 2 3 4 5

Info from dmesg:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
      ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
      ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: C/H/S=28733/16/255 from BIOS ignored
hda: ST360021A, ATA DISK drive
hda: DMA disabled
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: RICOH CD-R/RW MP7163A, ATAPI CD/DVD-ROM drive
hdd: CD-ROM 32X/AKU, ATAPI CD/DVD-ROM drive
hdc: DMA disabled
hdd: DMA disabled
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63,
UDMA(100)
   hda: hda1 < hda5 > hda2 hda3
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA


(Why does it say DMA disabled there [for hda], yet hdparm says its
enabled? I checked that there is no init script changing settings on the
drives.)

Re: IDE performance slowdown in 2.5

[Nero]

Nero wrote:

> With 2.5.47, I get 22mb/s using hdparm -t /dev/hda, and close to 40mb/s
> when running 2.4.x
> Is this at all expected?
> Info from hdparm:
>
> [13:19:08] root@debian:/proc# hdparm -v /dev/hda
> /dev/hda:
>   multcount    =  0 (off)
>   IO_support   =  1 (32-bit)
>   unmaskirq    =  1 (on)
>   using_dma    =  1 (on)
>   keepsettings =  0 (off)
>   readonly     =  0 (off)
>   readahead    = 256 (on)
>   geometry     = 50765/16/63, sectors = 117231408, start = 0
>
>
> [13:18:51] root@debian:/proc# hdparm -i /dev/hda
> /dev/hda:
>
>   Model=ST360021A, FwRev=3.05, SerialNo=3HR01F5W
>   Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
>   RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
>   BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
>   CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=117231408
>   IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
>   PIO modes:  pio0 pio1 pio2 pio3 pio4
>   DMA modes:  mdma0 mdma1 mdma2
>   UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
>   AdvancedPM=no WriteCache=enabled
>   Drive conforms to: device does not report version:  1 2 3 4 5
>
> Info from dmesg:
> ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx
> VP_IDE: IDE controller at PCI slot 00:07.1
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with 
> idebus=xx
> VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
>      ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
>      ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
> hda: C/H/S=28733/16/255 from BIOS ignored
> hda: ST360021A, ATA DISK drive
> hda: DMA disabled
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: RICOH CD-R/RW MP7163A, ATAPI CD/DVD-ROM drive
> hdd: CD-ROM 32X/AKU, ATAPI CD/DVD-ROM drive
> hdc: DMA disabled
> hdd: DMA disabled
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: host protected area => 1
> hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63,
> UDMA(100)
>   hda: hda1 < hda5 > hda2 hda3
> hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
>
>
> (Why does it say DMA disabled there [for hda], yet hdparm says its
> enabled? I checked that there is no init script changing settings on the
> drives.)

Forgot to mention, the filesystem is ReiserFS 3.