IDE siimage Problem

["O.Sezer" <sezero@superonline.com>]

[-- Attachment #1: Type: text/plain, Size: 3373 bytes --]

Sorry for reposting, but I think my original post got lost.
Now, onto the problem:



Kernel-1 : 2.4.19.16mdk or .24mdk with or without packet-writing patch.
	   (pre-compilead binary or compiled on this machine).

Kernel-2 : 2.4.21-pre5+bk (with or without packet-writing patch)
	   OR 2.4.21-pre4q13 from mandrake-cooker (pre-compiled
	   binary or compiled on this machine).
	   When compiled here, I excluded the acpi and swsusp options.

IDE Card = InnoVision EIO UltraATA/133 RAID pci card

With Kernel-1, I can successfully boot and run my system whether
or not I use vga=788. From dmesg:
CMD680: IDE controller on PCI bus 00 dev 50
PCI: Found IRQ 4 for device 00:0a.0
CMD680: chipset revision 2
CMD680: not 100% native mode: will probe irqs later
      ide2: BM-DMA at 0xa800-0xa807, BIOS settings: hde:pio, hdf:pio
      ide3: BM-DMA at 0xa808-0xa80f, BIOS settings: hdg:pio, hdh:pio
hdc: SONY CD-ROM CDU5221, ATAPI CD/DVD-ROM drive
hdd: RICOH CD-R/RW MP7200A, ATAPI CD/DVD-ROM drive
hde: ST320014A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd000-0xd007,0xb802 on irq 4
hde: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
Partition check:
   /dev/ide/host2/bus0/target0/lun0:<6> [PTBL] [2434/255/63] p1 p2 < p5 >
p3 p4


With Kernel-2, if I use vga=normal, then everything seems normal -
I can boot and run my system. From dmesg:
SiI680: IDE controller at PCI slot 00:0a.0
PCI: Found IRQ 4 for device 00:0a.0
SiI680: chipset revision 2
SiI680: not 100% native mode: will probe irqs later
SiI680: BASE CLOCK == 133
      ide2: MMIO-DMA at 0xd0800000-0xd0800007, BIOS settings: hde:pio,
hdf:pio
      ide3: MMIO-DMA at 0xd0800008-0xd080000f, BIOS settings: hdg:pio,
hdh:pio
hdc: SONY CD-ROM CDU5221, ATAPI CD/DVD-ROM drive
hdd: RICOH CD-R/RW MP7200A, ATAPI CD/DVD-ROM drive
hde: ST320014A, ATA DISK drive
blk: queue c031f3e0, I/O limit 4095Mb (mask 0xffffffff)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd0800080-0xd0800087,0xd080008a on irq 4
hde: host protected area => 1
hde: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
Partition check:
   /dev/ide/host2/bus0/target0/lun0:<6> [PTBL] [2434/255/63] p1 p2 < p5 >
p3 p4


Now, with Kernel-2, if I use vga=788, boot fails:
------ Hand copied from screen.
------ Messages when tried to boot with vga=788
SiI680: not 100% native mode: will probe irqs later
SiI680: BASE CLOCK == 133
      ide2: MMIO-DMA at 0xd8801000-0xd8801007 - Error MMIO ports already
in use
      ide3: MMIO-DMA at 0xd8801008-0xd880100f - Error MMIO ports already
in use
ide2: ports already in use, skipping probe
ide3: ports already in use, skipping probe
----- SNIPPED --------
Mounted devfs on /dev
Red Hat nash 3.1.6 starting
Mounting /proc filesystem
Creating root device
Mounting root filesystem
mount: error 6 mounting ext2 flags  Mounted devfs on /dev
Freeing unused kernel memory: 140k freed
Kernel panic: No init found. Try passing init= option to kernel.

In these three cases, there are interesting address differences
which mean nothing to me...
As another data-point, this problem does NOT occur with a HPT366
pci card.

What can I do to overcome this problem? Full dmesg logs, config,
and lspci output are gzipped and attached. I can provide any more
information which maybe necessary.

Kindest regards,
Ozkan Sezer
PS: I am not on the lkml, please CC me.


[-- Attachment #2: config.gz --]
[-- Type: application/gzip, Size: 12052 bytes --]

[-- Attachment #3: dmesg-2.4.19.16mdk.gz --]
[-- Type: application/gzip, Size: 3714 bytes --]

[-- Attachment #4: dmesg-nofb.log.gz --]
[-- Type: application/gzip, Size: 3426 bytes --]

[-- Attachment #5: screen-msg-fb.log.gz --]
[-- Type: application/gzip, Size: 412 bytes --]

[-- Attachment #6: lspci-v.out.gz --]
[-- Type: application/gzip, Size: 901 bytes --]