public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed
From: Lars <lhofhansl@yahoo.com>
To: Tomas Szepe <szepe@pinerecords.com>
Cc: Jeffrey Baker <jwbaker@acm.org>, linux-kernel@vger.kernel.org
Subject: Re: HD DMA disabled in 2.4.21-rc2, works fine in 2.4.20
Date: Sun, 18 May 2003 20:03:16 -0700	[thread overview]
Message-ID: <3EC84974.4020507@yahoo.com> (raw)
In-Reply-To: <20030518075910.GX3478@louise.pinerecords.com>

Tomas Szepe wrote:
>>[jwbaker@acm.org]
>>
>>I have the same problem on VIA chipset.  IDE DMA is disabled in
>>2.4.21-rc2 but works fine otherwise:
> 
> 
> Please post the relevant extract of your .config and dmesg output.
> 

Here's all the information:

dmesg:
------
...
PCI: PCI BIOS revision 2.10 entry at 0xfc06e, last bus=8
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX [8086/244c] at 00:1f.0
...
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HITACHI_DK23CA-30, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
hdc: TOSHIBA CD-RW/DVD-ROM SD-R2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB) w/2048KiB Cache, CHS=3648/255/63
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >

.config:
--------
...
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
...
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y

#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set
...

lspci:
------
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and 
Memory Controller Hub (rev 04)
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801BA PCI (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (ICH2) (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
00:1f.2 USB Controller: Intel Corporation 82801BA(M) USB (Hub A) (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 
0112 (revb2)
02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i 
PCI Audio Accelerator (rev 10)
02:06.0 PCI bridge: Action Tec Electronics Inc: Unknown device 0100 (rev 11)
02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8027
08:04.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] 
(rev 08)08:08.0 Communication controller: Lucent Microelectronics 
WinModem 56k (rev 01)


  reply	other threads:[~2003-05-19  2:50 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2003-05-17  3:56 HD DMA disabled in 2.4.21-rc2, works fine in 2.4.20 Jeffrey Baker
2003-05-18  7:59 ` Tomas Szepe
2003-05-19  3:03   ` Lars [this message]
  -- strict thread matches above, loose matches on Subject: below --
2003-05-24  2:45 Lars
2003-05-22  7:06 Lars
2003-05-19 23:12 Mudama, Eric
2003-05-19 19:56 Mudama, Eric
2003-05-19 20:04 ` Jeffrey W. Baker
2003-05-19 19:45   ` Alan Cox
2003-05-19 22:29     ` Tomas Szepe
2003-05-19 23:00       ` Jeffrey W. Baker
2003-05-20  1:25 ` lars hofhansl
2003-05-15  7:56 Lars

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3EC84974.4020507@yahoo.com \
    --to=lhofhansl@yahoo.com \
    --cc=jwbaker@acm.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=szepe@pinerecords.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox