SATA and 2.6.0-test9

public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed

* SATA and 2.6.0-test9
@ 2003-10-27 14:15 Patrik Wallstrom
  2003-10-27 16:58 ` Jeff Garzik
  0 siblings, 1 reply; 8+ messages in thread
From: Patrik Wallstrom @ 2003-10-27 14:15 UTC (permalink / raw)
  To: linux-kernel

> Jeff Garzik:
>   o [libata] Merge Serial ATA core, and drivers for
>   o [libata] Integrate Serial ATA driver into kernel tree

I am happy to see these in the kernel now, but I have yet to get them
working on my KT6 Delta KT600 motherboard with the VT8237 SATA
southbridge controller or even the Promise controller.

These are the devices:

  Bus  0, device  13, function  0:
    RAID bus controller: PCI device 105a:3373 (Promise Technology, )
    (rev 2).
      IRQ 19.
      Master Capable.  Latency=96.  Min Gnt=4.Max Lat=18.
      I/O at 0xec00 [0xec3f].
      I/O at 0xe800 [0xe80f].
      I/O at 0xe400 [0xe47f].
      Non-prefetchable 32 bit memory at 0xdffdb000 [0xdffdbfff].
      Non-prefetchable 32 bit memory at 0xdffa0000 [0xdffbffff].

Bus  0, device  15, function  0:
    RAID bus controller: PCI device 1106:3149 (VIA Technologies, In)
    (rev 128).
      IRQ 16.
      Master Capable.  Latency=32.
      I/O at 0xd800 [0xd807].
      I/O at 0xd400 [0xd403].
      I/O at 0xd000 [0xd007].
      I/O at 0xcc00 [0xcc03].
      I/O at 0xc800 [0xc80f].
      I/O at 0xc400 [0xc4ff].


And I am booting the kernel with these parameters to not let the IDE
drivers catch the SATA-drives:
ide2=noprobe ide3=noprobe hde=noprobe hdg=noprobe apm=power-off

I am booting from a working IDE drive, to see if I can get the
SATA-drives working:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DPTA-372050, ATA DISK drive
hdb: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 40088160 sectors (20525 MB) w/1961KiB Cache, CHS=39770/16/63, UDMA(33)
 hda: hda1 hda2 hda3
hdb: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)


And here is the SATA on the Promise chipset (SATA378 TX2plus):
libata version 0.75 loaded.
sata_via version 0.11
ata1: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
ATA: abnormal status 0x7F on port 0xD807
scsi0 : sata_via
ata1: thread exiting
ATA: abnormal status 0x7F on port 0xD007
ata2: thread exiting
scsi1 : sata_via
(kernel continues)

SATA on the VIA-chipset (VIA Serial ATA RAID):
ata1: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
ata1: dev 0 ATA, max UDMA/133, 156301488 sectors (lba48)
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: dev 0 ATA, max UDMA/133, 156301488 sectors (lba48)
ata2: dev 0 configured for UDMA/133
scsi1 : sata_via
  Vendor: ATA       Model: ST380013AS        Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: ST380013AS        Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write through
 sda:<3>ata1: DMA timeout, stat 0x4
(then hangs the kernel)

What can I do to make either the Promise or the VIA interface work
fine with the SATA disks?

-- 
patrik_wallstrom->foodfight->pawal@blipp.com->+46-733173956
                `-> http://www.gnuheter.com/

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: SATA and 2.6.0-test9
  2003-10-27 14:15 SATA and 2.6.0-test9 Patrik Wallstrom
@ 2003-10-27 16:58 ` Jeff Garzik
  2003-10-27 18:10   ` Patrik Wallstrom
  0 siblings, 1 reply; 8+ messages in thread
From: Jeff Garzik @ 2003-10-27 16:58 UTC (permalink / raw)
  To: Patrik Wallstrom; +Cc: linux-kernel

On Mon, Oct 27, 2003 at 03:15:32PM +0100, Patrik Wallstrom wrote:
> > Jeff Garzik:
> >   o [libata] Merge Serial ATA core, and drivers for
> >   o [libata] Integrate Serial ATA driver into kernel tree
> 
> I am happy to see these in the kernel now, but I have yet to get them
> working on my KT6 Delta KT600 motherboard with the VT8237 SATA
> southbridge controller or even the Promise controller.

Does it improve things, if you change ATA_FLAG_SRST to
ATA_FLAG_SATA_RESET, in drivers/scsi/sata_via.c ?

	Jeff




^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: SATA and 2.6.0-test9
  2003-10-27 16:58 ` Jeff Garzik
@ 2003-10-27 18:10   ` Patrik Wallstrom
  2003-10-30  1:29     ` [PATCH] " Jeff Garzik
  2003-10-30 17:49     ` [PATCH #2] " Jeff Garzik
  0 siblings, 2 replies; 8+ messages in thread
From: Patrik Wallstrom @ 2003-10-27 18:10 UTC (permalink / raw)
  To: Jeff Garzik; +Cc: linux-kernel

On Mon, 27 Oct 2003, Jeff Garzik wrote:

> > > Jeff Garzik:
> > >   o [libata] Merge Serial ATA core, and drivers for
> > >   o [libata] Integrate Serial ATA driver into kernel tree
> > 
> > I am happy to see these in the kernel now, but I have yet to get them
> > working on my KT6 Delta KT600 motherboard with the VT8237 SATA
> > southbridge controller or even the Promise controller.
> 
> Does it improve things, if you change ATA_FLAG_SRST to
> ATA_FLAG_SATA_RESET, in drivers/scsi/sata_via.c ?

It doesn't hang any more, but the only result is:
sata_via version 0.11
ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
ata3: thread exiting
scsi2 : sata_via
ata4: thread exiting
scsi3 : sata_via

-- 
patrik_wallstrom->foodfight->pawal@blipp.com->+46-733173956
                `-> http://www.gnuheter.com/

^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH] Re: SATA and 2.6.0-test9
  2003-10-27 18:10   ` Patrik Wallstrom
@ 2003-10-30  1:29     ` Jeff Garzik
  2003-10-30 17:49     ` [PATCH #2] " Jeff Garzik
  1 sibling, 0 replies; 8+ messages in thread
From: Jeff Garzik @ 2003-10-30  1:29 UTC (permalink / raw)
  To: Patrik Wallstrom; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 982 bytes --]

Patrik Wallstrom wrote:
> On Mon, 27 Oct 2003, Jeff Garzik wrote:
> 
> 
>>>>Jeff Garzik:
>>>>  o [libata] Merge Serial ATA core, and drivers for
>>>>  o [libata] Integrate Serial ATA driver into kernel tree
>>>
>>>I am happy to see these in the kernel now, but I have yet to get them
>>>working on my KT6 Delta KT600 motherboard with the VT8237 SATA
>>>southbridge controller or even the Promise controller.
>>
>>Does it improve things, if you change ATA_FLAG_SRST to
>>ATA_FLAG_SATA_RESET, in drivers/scsi/sata_via.c ?
> 
> 
> It doesn't hang any more, but the only result is:
> sata_via version 0.11
> ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
> ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
> ata3: thread exiting
> scsi2 : sata_via
> ata4: thread exiting
> scsi3 : sata_via

Duh...  I was missing a piece in libata-core.c, and clobbering some 
information I needed.

Can you try this patch, and let me know if things change?

	Jeff



[-- Attachment #2: patch --]
[-- Type: text/plain, Size: 989 bytes --]

===== drivers/scsi/libata-core.c 1.5 vs edited =====
--- 1.5/drivers/scsi/libata-core.c	Wed Oct 22 22:25:32 2003
+++ edited/drivers/scsi/libata-core.c	Wed Oct 29 20:27:27 2003
@@ -1339,9 +1339,13 @@
 		outb(ap->ctl, ioaddr->ctl_addr);
 
 	/* determine if device 0/1 are present */
-	dev0 = ata_dev_devchk(ap, 0);
-	if (slave_possible)
-		dev1 = ata_dev_devchk(ap, 1);
+	if (ap->flags & ATA_FLAG_SATA_RESET)
+		dev0 = 1;
+	else {
+		dev0 = ata_dev_devchk(ap, 0);
+		if (slave_possible)
+			dev1 = ata_dev_devchk(ap, 1);
+	}
 
 	if (dev0)
 		devmask |= (1 << 0);
===== drivers/scsi/sata_via.c 1.2 vs edited =====
--- 1.2/drivers/scsi/sata_via.c	Tue Oct 21 23:13:54 2003
+++ edited/drivers/scsi/sata_via.c	Wed Oct 29 20:27:43 2003
@@ -108,7 +108,7 @@
 	{
 		.sht		= &svia_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY
-				  | ATA_FLAG_SRST,
+				  | ATA_FLAG_SATA_RESET,
 		.pio_mask	= 0x03,	/* pio3-4 */
 		.udma_mask	= 0x7f,	/* udma0-6 ; FIXME */
 		.port_ops	= &svia_sata_ops,

^ permalink raw reply	[flat|nested] 8+ messages in thread

* [PATCH #2] Re: SATA and 2.6.0-test9
  2003-10-27 18:10   ` Patrik Wallstrom
  2003-10-30  1:29     ` [PATCH] " Jeff Garzik
@ 2003-10-30 17:49     ` Jeff Garzik
  2003-10-30 22:25       ` Patrik Wallstrom
  2003-10-31 12:14       ` Oliver M. Bolzer
  1 sibling, 2 replies; 8+ messages in thread
From: Jeff Garzik @ 2003-10-30 17:49 UTC (permalink / raw)
  To: Patrik Wallstrom; +Cc: linux-kernel

[-- Attachment #1: Type: text/plain, Size: 863 bytes --]

Patrik Wallstrom wrote:
> On Mon, 27 Oct 2003, Jeff Garzik wrote:
> 
> 
>>>>Jeff Garzik:
>>>>  o [libata] Merge Serial ATA core, and drivers for
>>>>  o [libata] Integrate Serial ATA driver into kernel tree
>>>
>>>I am happy to see these in the kernel now, but I have yet to get them
>>>working on my KT6 Delta KT600 motherboard with the VT8237 SATA
>>>southbridge controller or even the Promise controller.
>>
>>Does it improve things, if you change ATA_FLAG_SRST to
>>ATA_FLAG_SATA_RESET, in drivers/scsi/sata_via.c ?
> 
> 
> It doesn't hang any more, but the only result is:
> sata_via version 0.11
> ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
> ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
> ata3: thread exiting
> scsi2 : sata_via
> ata4: thread exiting
> scsi3 : sata_via

Actually, attached is a better patch...

[-- Attachment #2: patch --]
[-- Type: text/plain, Size: 2294 bytes --]

===== drivers/scsi/libata-core.c 1.5 vs edited =====
--- 1.5/drivers/scsi/libata-core.c	Wed Oct 22 22:25:32 2003
+++ edited/drivers/scsi/libata-core.c	Thu Oct 30 11:18:59 2003
@@ -1086,6 +1086,11 @@
 	if (ap->flags & ATA_FLAG_PORT_DISABLED)
 		return;
 
+	if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
+		ata_port_disable(ap);
+		return;
+	}
+
 	ata_bus_reset(ap);
 }
 
@@ -1339,9 +1344,13 @@
 		outb(ap->ctl, ioaddr->ctl_addr);
 
 	/* determine if device 0/1 are present */
-	dev0 = ata_dev_devchk(ap, 0);
-	if (slave_possible)
-		dev1 = ata_dev_devchk(ap, 1);
+	if (ap->flags & ATA_FLAG_SATA_RESET)
+		dev0 = 1;
+	else {
+		dev0 = ata_dev_devchk(ap, 0);
+		if (slave_possible)
+			dev1 = ata_dev_devchk(ap, 1);
+	}
 
 	if (dev0)
 		devmask |= (1 << 0);
===== drivers/scsi/sata_promise.c 1.8 vs edited =====
--- 1.8/drivers/scsi/sata_promise.c	Tue Oct 28 11:04:25 2003
+++ edited/drivers/scsi/sata_promise.c	Thu Oct 30 08:13:44 2003
@@ -176,7 +176,7 @@
 	{
 		.sht		= &pdc_sata_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+				  ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO,
 		.pio_mask	= 0x03, /* pio3-4 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
 		.port_ops	= &pdc_sata_ops,
@@ -186,7 +186,7 @@
 	{
 		.sht		= &pdc_sata_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+				  ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO,
 		.pio_mask	= 0x03, /* pio3-4 */
 		.udma_mask	= 0x7f, /* udma0-6 ; FIXME */
 		.port_ops	= &pdc_sata_ops,
@@ -207,6 +207,8 @@
 
 static struct pci_device_id pdc_sata_pci_tbl[] = {
 	{ PCI_VENDOR_ID_PROMISE, 0x3371, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	  board_2037x },
+	{ PCI_VENDOR_ID_PROMISE, 0x3373, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 	  board_2037x },
 	{ PCI_VENDOR_ID_PROMISE, 0x3375, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 	  board_2037x },
===== drivers/scsi/sata_via.c 1.2 vs edited =====
--- 1.2/drivers/scsi/sata_via.c	Tue Oct 21 23:13:54 2003
+++ edited/drivers/scsi/sata_via.c	Wed Oct 29 20:27:43 2003
@@ -108,7 +108,7 @@
 	{
 		.sht		= &svia_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY
-				  | ATA_FLAG_SRST,
+				  | ATA_FLAG_SATA_RESET,
 		.pio_mask	= 0x03,	/* pio3-4 */
 		.udma_mask	= 0x7f,	/* udma0-6 ; FIXME */
 		.port_ops	= &svia_sata_ops,

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH #2] Re: SATA and 2.6.0-test9
  2003-10-30 17:49     ` [PATCH #2] " Jeff Garzik
@ 2003-10-30 22:25       ` Patrik Wallstrom
  2003-10-30 22:27         ` Jeff Garzik
  2003-10-31 12:14       ` Oliver M. Bolzer
  1 sibling, 1 reply; 8+ messages in thread
From: Patrik Wallstrom @ 2003-10-30 22:25 UTC (permalink / raw)
  To: Jeff Garzik; +Cc: linux-kernel

On Thu, 30 Oct 2003, Jeff Garzik wrote:

> >It doesn't hang any more, but the only result is:
> >sata_via version 0.11
> >ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
> >ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
> >ata3: thread exiting
> >scsi2 : sata_via
> >ata4: thread exiting
> >scsi3 : sata_via
> 
> Actually, attached is a better patch...

Still get the same result as above.

(
patching file drivers/scsi/sata_via.c
Hunk #1 succeeded at 105 (offset -3 lines).
)

Is there any way to know why the thread is exiting?

-- 
patrik_wallstrom->foodfight->pawal@blipp.com->+46-733173956
                `-> http://www.gnuheter.com/

^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH #2] Re: SATA and 2.6.0-test9
  2003-10-30 22:25       ` Patrik Wallstrom
@ 2003-10-30 22:27         ` Jeff Garzik
  0 siblings, 0 replies; 8+ messages in thread
From: Jeff Garzik @ 2003-10-30 22:27 UTC (permalink / raw)
  To: Patrik Wallstrom; +Cc: linux-kernel

Patrik Wallstrom wrote:
> On Thu, 30 Oct 2003, Jeff Garzik wrote:
> 
> 
>>>It doesn't hang any more, but the only result is:
>>>sata_via version 0.11
>>>ata3: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 16
>>>ata4: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 16
>>>ata3: thread exiting
>>>scsi2 : sata_via
>>>ata4: thread exiting
>>>scsi3 : sata_via
>>
>>Actually, attached is a better patch...
> 
> 
> Still get the same result as above.

Ok, thanks for testing.


> Is there any way to know why the thread is exiting?

That's normal, when it cannot find a device on that port.

	Jeff





^ permalink raw reply	[flat|nested] 8+ messages in thread

* Re: [PATCH #2] Re: SATA and 2.6.0-test9
  2003-10-30 17:49     ` [PATCH #2] " Jeff Garzik
  2003-10-30 22:25       ` Patrik Wallstrom
@ 2003-10-31 12:14       ` Oliver M. Bolzer
  1 sibling, 0 replies; 8+ messages in thread
From: Oliver M. Bolzer @ 2003-10-31 12:14 UTC (permalink / raw)
  To: linux-kernel; +Cc: Jeff Garzik

On Thu, Oct 30, 2003 at 12:49:35PM -0500, Jeff Garzik <jgarzik@pobox.com> wrote...

> >>Does it improve things, if you change ATA_FLAG_SRST to
> >>ATA_FLAG_SATA_RESET, in drivers/scsi/sata_via.c ?
 
> Actually, attached is a better patch...


I've tried the patch on my Promise FastTrak S150 TX4 and it improves
things a lot. The drives and even the partitions are corretly
recognized, at least for the first 3 ports. The 4th port seems to
hang after sending it the ATA_CMD_READ_EXT (0x25) command, resulting
in a DMA timeout and the same endless loop that occured when the ports
could not be resetted (vanilla 2.6.0-test9 without SRST flag).

Would it be useful if I unhook the 4th drive to see how much further
the driver can proceed with the first 3 drives?

Below the dmesg output with ATA_DEBUG and ATA_VERBOSE_DEBUG
defined.

Linux version 2.6.0-test9 (bolzer@ravioli) (gcc version 3.2) #17 Fri Oct 31 11:49:53 CET 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009cc00 (usable)
 BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003f7f0000 (usable)
 BIOS-e820: 000000003f7f0000 - 000000003f800000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
119MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f9bf0
hm, page 000f9000 reserved twice.
hm, page 000fa000 reserved twice.
hm, page 000ed000 reserved twice.
hm, page 000ee000 reserved twice.
On node 0 totalpages: 260080
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 30704 pages, LIFO batch:7
DMI 2.3 present.
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: COMPAQ   Product ID:              APIC at: 0xFEE00000
Processor #0 15:2 APIC version 16
I/O APIC #8 Version 17 at 0xFEC00000.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Processors: 1
Building zonelist for node : 0
Kernel command line: console=ttyS0 console=tty0 log_buf_len=128k nfsroot=XXX.XXX.XXX.XXX:/var/cipinstall,rsize=8192,wsize=8192 ip=::::::dhcp BOOT_IMAGE=vmlinuz.install-2.6.0t9-silo 
log_buf_len: 131072
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2525.454 MHz processor.
Console: colour VGA+ 80x25
Memory: 1025360k/1040320k available (2222k kernel code, 14008k reserved, 925k data, 156k init, 122816k highmem)
Calibrating delay loop... 4980.73 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 8 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 8 ... ok.
..TIMER: vector=0x31 pin1=-1 pin2=-1
...trying to set up timer (IRQ0) through the 8259A ...  failed.
...trying to set up timer as Virtual Wire IRQ... works.
testing the IO APIC.......................
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2524.0906 MHz.
..... host bus clock speed is 132.0889 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.20 entry at 0xeca48, last bus=5
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fefe0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x6627, dseg 0xf0000
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX [8086/24c0] at 0000:00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B5,I4,P0) -> 16
PCI->APIC IRQ transform: (B5,I8,P0) -> 20
PCI->APIC IRQ transform: (B5,I10,P0) -> 21
Machine check exception polling timer started.
cpufreq: P4/Xeon(TM) CPU On-Demand Clock Modulation available
ikconfig 0.7 with /proc/config*
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
Initializing Cryptographic API
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
hw_random: RNG not detected
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/100 Network Driver - version 2.3.30-k1
Copyright (c) 2003 Intel Corporation
e100: eth0: Intel(R) PRO/100 Network Connection
  Hardware receive checksums enabled
tg3.c:v2.2 (August 24, 2003)
eth1: Tigon3 [partno(AC91002A1) rev 0105 PHY(5701)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:09:5b:60:df:a3
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x24c0-0x24c7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x24c8-0x24cf, BIOS settings: hdc:pio, hdd:pio
ata_device_add: ENTER
ata_host_add: ENTER
ata_host_add: prd alloc, virt f7de8000, dma 37de8000
ata1: SATA max UDMA/133 cmd 0xF8813200 ctl 0xF8813238 bmdma 0x0 irq 16
ata_host_add: ENTER
ata_thread_iter: ata1: thr_state THR_PROBE_START
ata_host_add: prd alloc, virt f7de7000, dma 37de7000
ata2: SATA max UDMA/133 cmd 0xF8813280 ctl 0xF88132B8 bmdma 0x0 irq 16
ata_host_add: ENTER
ata_thread_iter: ata2: thr_state THR_PROBE_START
ata_host_add: prd alloc, virt f7de6000, dma 37de6000
ata3: SATA max UDMA/133 cmd 0xF8813300 ctl 0xF8813338 bmdma 0x0 irq 16
ata_host_add: ENTER
ata_thread_iter: ata3: thr_state THR_PROBE_START
ata_host_add: prd alloc, virt f7de5000, dma 37de5000
ata4: SATA max UDMA/133 cmd 0xF8813380 ctl 0xF88133B8 bmdma 0x0 irq 16
ata_device_add: probe begin
ata_device_add: ata1: probe begin
ata_device_add: ata1: probe-wait begin
ata_thread_iter: ata1: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata1: thr_state THR_PORT_RESET
ata_thread_iter: ata4: thr_state THR_PROBE_START
ata_bus_reset: ENTER, host 1, port 0
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 1, dev 0
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata1: cmd 0xEC
ata_exec_command_mmio: ata1: cmd 0xEC
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0407  64==0x0003  75==0x0000  
ata_dump_id: 80==0x00fe  81==0x001e  82==0x7c6b  83==0x7f09  84==0x4003  
ata_dump_id: 88==0x207f  93==0x0000
ata1: dev 0 ATA, max UDMA/133, 398297088 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 1, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata1: cmd 0xEF
ata_exec_command_mmio: ata1: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata1: dev 0 configured for UDMA/133
ata_thread_iter: ata1: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata1: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 0
ata_device_add: ata1: probe-wait end
scsi0 : sata_promise
ata_device_add: ata2: probe begin
ata_device_add: ata2: probe-wait begin
ata_thread_iter: ata2: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata2: thr_state THR_PORT_RESET
ata_thread_iter: ata1: thr_state THR_IDLE
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 30000
ata_bus_reset: ENTER, host 2, port 1
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 2, dev 0
ata_dev_select: ENTER, ata2: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata2: cmd 0xEC
ata_exec_command_mmio: ata2: cmd 0xEC
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0407  64==0x0003  75==0x0000  
ata_dump_id: 80==0x00fe  81==0x001e  82==0x7c6b  83==0x7f09  84==0x4003  
ata_dump_id: 88==0x207f  93==0x0000
ata2: dev 0 ATA, max UDMA/133, 398297088 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 2, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata2: cmd 0xEF
ata_exec_command_mmio: ata2: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata2: dev 0 configured for UDMA/133
ata_thread_iter: ata2: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata2: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 0
ata_device_add: ata2: probe-wait end
scsi1 : sata_promise
ata_device_add: ata3: probe begin
ata_device_add: ata3: probe-wait begin
ata_thread_iter: ata3: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata3: thr_state THR_PORT_RESET
ata_thread_iter: ata2: thr_state THR_IDLE
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 30000
ata_bus_reset: ENTER, host 3, port 2
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 3, dev 0
ata_dev_select: ENTER, ata3: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata3: cmd 0xEC
ata_exec_command_mmio: ata3: cmd 0xEC
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0407  64==0x0003  75==0x0000  
ata_dump_id: 80==0x00fe  81==0x001e  82==0x7c6b  83==0x7f09  84==0x4003  
ata_dump_id: 88==0x207f  93==0x0000
ata3: dev 0 ATA, max UDMA/133, 398297088 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 3, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata3: cmd 0xEF
ata_exec_command_mmio: ata3: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata3: dev 0 configured for UDMA/133
ata_thread_iter: ata3: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata3: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata3: new thr_state THR_IDLE, returning 0
ata_device_add: ata3: probe-wait end
scsi2 : sata_promise
ata_device_add: ata4: probe begin
ata_device_add: ata4: probe-wait begin
ata_thread_iter: ata4: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata4: thr_state THR_PORT_RESET
ata_thread_iter: ata3: thr_state THR_IDLE
ata_thread_iter: ata3: new thr_state THR_IDLE, returning 30000
ata_bus_reset: ENTER, host 4, port 3
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 4, dev 0
ata_dev_select: ENTER, ata4: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata4: cmd 0xEC
ata_exec_command_mmio: ata4: cmd 0xEC
ata_dump_id: 49==0x2f00  53==0x0007  63==0x0407  64==0x0003  75==0x0000  
ata_dump_id: 80==0x00fe  81==0x001e  82==0x7c6b  83==0x7f09  84==0x4003  
ata_dump_id: 88==0x207f  93==0x0000
ata4: dev 0 ATA, max UDMA/133, 398297088 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 4, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata4: cmd 0xEF
ata_exec_command_mmio: ata4: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata4: dev 0 configured for UDMA/133
ata_thread_iter: ata4: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata4: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata4: new thr_state THR_IDLE, returning 0
ata_device_add: ata4: probe-wait end
scsi3 : sata_promise
ata_device_add: probe begin
ata_scsi_queuecmd: CDB (1:0,0,0) 12 00 00 00 24 00 dd f7 00
ata_scsiop_inq_std: ENTER
ata_scsi_queuecmd: CDB (1:0,0,0) 12 00 00 00 61 00 dd f7 00
ata_scsiop_inq_std: ENTER
  Vendor: ATA       Model: Maxtor 6Y200M0    Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
ata_scsi_queuecmd: CDB (1:0,0,0) a0 00 00 00 00 00 00 00 04
ata_scsiop_report_luns: ENTER
ata_scsi_queuecmd: CDB (1:0,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: no device
ata_scsi_queuecmd: CDB (1:0,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:0,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,0,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (1:1,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_queuecmd: CDB (2:0,0,0) 12 00 00 00 61 00 00 00 00
ata_scsiop_inq_std: ENTER
  Vendor: ATA       Model: Maxtor 6Y200M0    Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
ata_scsi_queuecmd: CDB (2:0,0,0) a0 00 00 00 00 00 00 00 04
ata_scsiop_report_luns: ENTER
ata_scsi_queuecmd: CDB (2:0,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: no device
ata_scsi_queuecmd: CDB (2:0,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:0,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,0,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (2:1,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_queuecmd: CDB (3:0,0,0) 12 00 00 00 61 00 00 00 00
ata_scsiop_inq_std: ENTER
  Vendor: ATA       Model: Maxtor 6Y200M0    Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
ata_scsi_queuecmd: CDB (3:0,0,0) a0 00 00 00 00 00 00 00 04
ata_scsiop_report_luns: ENTER
ata_scsi_queuecmd: CDB (3:0,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: no device
ata_scsi_queuecmd: CDB (3:0,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:0,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,0,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (3:1,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_queuecmd: CDB (4:0,0,0) 12 00 00 00 61 00 00 00 00
ata_scsiop_inq_std: ENTER
  Vendor: ATA       Model: Maxtor 6Y200M0    Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
ata_scsi_queuecmd: CDB (4:0,0,0) a0 00 00 00 00 00 00 00 04
ata_scsiop_report_luns: ENTER
ata_scsi_queuecmd: CDB (4:0,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: no device
ata_scsi_queuecmd: CDB (4:0,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:0,15,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,0,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,1,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,2,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,3,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,4,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,5,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,6,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,7,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,8,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,9,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,10,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,11,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,12,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,13,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,14,0) 12 00 00 00 24 00 00 00 00
ata_scsi_queuecmd: CDB (4:1,15,0) 12 00 00 00 24 00 00 00 00
ata_device_add: EXIT, returning 4
ata_scsi_queuecmd: CDB (1:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (1:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
ata_scsi_queuecmd: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sda: drive cache: write through
 sda:<3>ata_scsi_queuecmd: CDB (1:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_sg_setup: ENTER, ata1, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x37DA7000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
pdc_dma_start: ENTER, ap f7dec9a8, mmio f8813000
pdc_dma_start: val == 80008001
pdc_dma_start: val == 80008001
ata_exec_command_mmio: ata1: cmd 0x25
pdc_dma_start: FIVE
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: port 1
pdc_interrupt: port 2
pdc_interrupt: port 3
pdc_interrupt: EXIT
 sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (2:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (2:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
ata_scsi_queuecmd: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sdb: drive cache: write through
 sdb:<3>ata_scsi_queuecmd: CDB (2:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata2: device 0, wait 1
ata_sg_setup: ENTER, ata2, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x37DA6000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
pdc_dma_start: ENTER, ap f7dec1a8, mmio f8813000
pdc_dma_start: val == 80008002
pdc_dma_start: val == 80008002
ata_exec_command_mmio: ata2: cmd 0x25
pdc_dma_start: FIVE
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
pdc_interrupt: port 1
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: port 2
pdc_interrupt: port 3
pdc_interrupt: EXIT
ata_thread_iter: ata4: thr_state THR_IDLE
ata_thread_iter: ata4: new thr_state THR_IDLE, returning 30000
 sdb1 sdb2 sdb3
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (3:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (3:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
ata_scsi_queuecmd: CDB (3:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (3:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sdc: drive cache: write through
 sdc:<3>ata_scsi_queuecmd: CDB (3:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata3: device 0, wait 1
ata_sg_setup: ENTER, ata3, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x37DA5000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
pdc_dma_start: ENTER, ap f7fed9a8, mmio f8813000
pdc_dma_start: val == 80008003
pdc_dma_start: val == 80008003
ata_exec_command_mmio: ata3: cmd 0x25
pdc_dma_start: FIVE
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
pdc_interrupt: port 1
pdc_interrupt: port 2
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: port 3
pdc_interrupt: EXIT
 sdc1 sdc2 sdc3
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (4:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (4:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
ata_scsi_queuecmd: CDB (4:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (4:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sdd: drive cache: write through
 sdd:<3>ata_scsi_queuecmd: CDB (4:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata4: device 0, wait 1
ata_sg_setup: ENTER, ata4, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x37DA4000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
pdc_dma_start: ENTER, ap f7fed1a8, mmio f8813000
pdc_dma_start: val == 80008004
pdc_dma_start: val == 80008004
ata_exec_command_mmio: ata4: cmd 0x25
pdc_dma_start: FIVE
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: QUICK EXIT 3
ata_thread_iter: ata1: thr_state THR_IDLE
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata2: thr_state THR_IDLE
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata3: thr_state THR_IDLE
ata_thread_iter: ata3: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata4: thr_state THR_IDLE
ata_thread_iter: ata4: new thr_state THR_IDLE, returning 30000
ata_scsi_error: ENTER
pdc_eng_timeout: ENTER
ata4: DMA timeout
ata_sg_clean: unmapping 1 sg elements
pdc_eng_timeout: EXIT
ata_scsi_error: EXIT
ata_thread_iter: ata1: thr_state THR_IDLE
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata2: thr_state THR_IDLE
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata3: thr_state THR_IDLE
ata_thread_iter: ata3: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata4: thr_state THR_IDLE
ata_thread_iter: ata4: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata1: thr_state THR_IDLE
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata2: thr_state THR_IDLE
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 30000
ata_thread_iter: ata3: thr_state THR_IDLE
ata_thread_iter: ata3: new thr_state THR_IDLE, returning 30000
[endless loop]
-- 
	Oliver M. Bolzer
	oliver@gol.com

GPG (PGP) Fingerprint = 621B 52F6 2AC1 36DB 8761  018F 8786 87AD EF50 D1FF

^ permalink raw reply	[flat|nested] 8+ messages in thread

end of thread, other threads:[~2003-10-31 12:14 UTC | newest]

Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-10-27 14:15 SATA and 2.6.0-test9 Patrik Wallstrom
2003-10-27 16:58 ` Jeff Garzik
2003-10-27 18:10   ` Patrik Wallstrom
2003-10-30  1:29     ` [PATCH] " Jeff Garzik
2003-10-30 17:49     ` [PATCH #2] " Jeff Garzik
2003-10-30 22:25       ` Patrik Wallstrom
2003-10-30 22:27         ` Jeff Garzik
2003-10-31 12:14       ` Oliver M. Bolzer

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox