* Re: aacraid issues
2003-12-23 23:19 aacraid issues Yaroslav Klyukin
@ 2003-12-23 23:35 ` Mark Haverkamp
2003-12-24 3:02 ` Yaroslav Klyukin
0 siblings, 1 reply; 4+ messages in thread
From: Mark Haverkamp @ 2003-12-23 23:35 UTC (permalink / raw)
To: Yaroslav Klyukin; +Cc: linux-kernel
On Tue, 2003-12-23 at 15:19, Yaroslav Klyukin wrote:
> I have very strange aacraid behavior:
> First of all, I know, that aacraid support is experimental, but maybe
> the issue is related to something else in the kernel.
>
> I have AMD Opteron system with 10 scsi disks, connected to Adaptec 2200S
> controller, constituting about 1.2TB in total.
>
> I can boot with 2.4.22 kernel, compiled for Xeon, into RedHat 9
> (32 bit mode). aacraid version 1.1.2. The raid works great.
>
> Then I boot into SuSE Linux 9 for the Opterons, with 2.4.23 kernel.
> aacraid version 1.1-3.
>
> Seems to work, but when I try to access blocks close to the end of the
> RAID, I am getting I/O errors.
>
> Any ideas?
> Where can I get the latest patches for the aacraid driver?
>
> Just tried 2.6.0 kernel with patches for Opteron, but as soon as it
> starts working with Adaptec controller, it crashes miserably... :-(
>
Try this, someone else with a 2200 had a similar problem that this patch
fixed. It will apply to 2.6.0.
===== drivers/scsi/aacraid/aachba.c 1.20 vs edited =====
--- 1.20/drivers/scsi/aacraid/aachba.c Fri May 2 12:30:49 2003
+++ edited/drivers/scsi/aacraid/aachba.c Wed Dec 3 15:10:22 2003
@@ -525,6 +525,14 @@
if(dev->pae_support != 0) {
printk(KERN_INFO"%s%d: 64 Bit PAE enabled\n", dev->name, dev->id);
pci_set_dma_mask(dev->pdev, (dma_addr_t)0xFFFFFFFFFFFFFFFFULL);
+ } else {
+ /*
+ * Reset if Quirk 31 was used, since data
+ * transfers are ok.
+ */
+ if (pci_set_dma_mask(dev->pdev, 0xFFFFFFFFULL)) {
+ printk(KERN_INFO"aacraid: Can't reset DMA mask.\n");
+ }
}
fib_complete(fibptr);
===== drivers/scsi/aacraid/aacraid.h 1.9 vs edited =====
--- 1.9/drivers/scsi/aacraid/aacraid.h Wed Oct 22 02:52:43 2003
+++ edited/drivers/scsi/aacraid/aacraid.h Wed Dec 3 15:21:48 2003
@@ -529,6 +529,8 @@
char * vname;
char * model;
u16 channels;
+ int quirks;
+#define AAC_QUIRK_31BIT 1
};
/*
===== drivers/scsi/aacraid/linit.c 1.22 vs edited =====
--- 1.22/drivers/scsi/aacraid/linit.c Tue Aug 26 09:25:41 2003
+++ edited/drivers/scsi/aacraid/linit.c Wed Dec 3 15:22:42 2003
@@ -86,36 +86,47 @@
* for the card. At that time we can remove the channels from here
*/
static struct aac_driver_ident aac_drivers[] = {
- { 0x1028, 0x0001, 0x1028, 0x0001, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 2/Si */
- { 0x1028, 0x0002, 0x1028, 0x0002, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x1028, 0x0003, 0x1028, 0x0003, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Si */
- { 0x1028, 0x0004, 0x1028, 0x00d0, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Si */
- { 0x1028, 0x0002, 0x1028, 0x00d1, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x1028, 0x0002, 0x1028, 0x00d9, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x1028, 0x000a, 0x1028, 0x0106, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x1028, 0x000a, 0x1028, 0x011b, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x1028, 0x000a, 0x1028, 0x0121, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2 }, /* PERC 3/Di */
- { 0x9005, 0x0283, 0x9005, 0x0283, aac_rx_init, "aacraid", "ADAPTEC ", "catapult ", 2 }, /* catapult*/
- { 0x9005, 0x0284, 0x9005, 0x0284, aac_rx_init, "aacraid", "ADAPTEC ", "tomcat ", 2 }, /* tomcat*/
- { 0x9005, 0x0285, 0x9005, 0x0286, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2120S ", 1 }, /* Adaptec 2120S (Crusader)*/
- { 0x9005, 0x0285, 0x9005, 0x0285, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2 }, /* Adaptec 2200S (Vulcan)*/
- { 0x9005, 0x0285, 0x9005, 0x0287, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2 }, /* Adaptec 2200S (Vulcan-2m)*/
- { 0x9005, 0x0285, 0x17aa, 0x0286, aac_rx_init, "aacraid", "Legend ", "Legend S220 ", 1 }, /* Legend S220*/
- { 0x9005, 0x0285, 0x17aa, 0x0287, aac_rx_init, "aacraid", "Legend ", "Legend S230 ", 2 }, /* Legend S230*/
-
- { 0x9005, 0x0285, 0x9005, 0x0288, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3230S ", 2 }, /* Adaptec 3230S (Harrier)*/
- { 0x9005, 0x0285, 0x9005, 0x0289, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3240S ", 2 }, /* Adaptec 3240S (Tornado)*/
- { 0x9005, 0x0285, 0x9005, 0x028a, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S PCI-X ZCR (Skyhawk)*/
- { 0x9005, 0x0285, 0x9005, 0x028b, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S SO-DIMM PCI-X ZCR(Terminator)*/
- { 0x9005, 0x0285, 0x9005, 0x0290, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2410SA SATA ", 2 }, /* AAR-2410SA PCI SATA 4ch (Jaguar II)*/
- { 0x9005, 0x0250, 0x1014, 0x0279, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec ", 2 }, /* (Marco)*/
- { 0x9005, 0x0250, 0x1014, 0x028c, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec ", 2 }, /* (Sebring)*/
+ { 0x1028, 0x0001, 0x1028, 0x0001, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 2/Si (Iguana/PERC2Si) */
+ { 0x1028, 0x0002, 0x1028, 0x0002, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Opal/PERC3Di) */
+ { 0x1028, 0x0003, 0x1028, 0x0003, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Si (SlimFast/PERC3Si */
+ { 0x1028, 0x0004, 0x1028, 0x00d0, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Iguana FlipChip/PERC3DiF */
+ { 0x1028, 0x0002, 0x1028, 0x00d1, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Viper/PERC3DiV) */
+ { 0x1028, 0x0002, 0x1028, 0x00d9, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Lexus/PERC3DiL) */
+ { 0x1028, 0x000a, 0x1028, 0x0106, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 1, AAC_QUIRK_31BIT }, /* PERC 3/Di (Jaguar/PERC3DiJ) */
+ { 0x1028, 0x000a, 0x1028, 0x011b, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Dagger/PERC3DiD) */
+ { 0x1028, 0x000a, 0x1028, 0x0121, aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT }, /* PERC 3/Di (Boxster/PERC3DiB) */
+ { 0x9005, 0x0283, 0x9005, 0x0283, aac_rx_init, "aacraid", "ADAPTEC ", "catapult ", 2, AAC_QUIRK_31BIT }, /* catapult */
+ { 0x9005, 0x0284, 0x9005, 0x0284, aac_rx_init, "aacraid", "ADAPTEC ", "tomcat ", 2, AAC_QUIRK_31BIT }, /* tomcat */
+ { 0x9005, 0x0285, 0x9005, 0x0286, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2120S ", 1, AAC_QUIRK_31BIT }, /* Adaptec 2120S (Crusader) */
+ { 0x9005, 0x0285, 0x9005, 0x0285, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT }, /* Adaptec 2200S (Vulcan) */
+ { 0x9005, 0x0285, 0x9005, 0x0287, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT }, /* Adaptec 2200S (Vulcan-2m) */
+ { 0x9005, 0x0285, 0x17aa, 0x0286, aac_rx_init, "aacraid", "Legend ", "Legend S220 ", 1, AAC_QUIRK_31BIT }, /* Legend S220 (Legend Crusader) */
+ { 0x9005, 0x0285, 0x17aa, 0x0287, aac_rx_init, "aacraid", "Legend ", "Legend S230 ", 2, AAC_QUIRK_31BIT }, /* Legend S230 (Legend Vulcan) */
+
+ { 0x9005, 0x0285, 0x9005, 0x0288, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3230S ", 2 }, /* Adaptec 3230S (Harrier) */
+ { 0x9005, 0x0285, 0x9005, 0x0289, aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3240S ", 2 }, /* Adaptec 3240S (Tornado) */
+ { 0x9005, 0x0285, 0x9005, 0x028a, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S PCI-X ZCR (Skyhawk) */
+ { 0x9005, 0x0285, 0x9005, 0x028b, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020S PCI-X ", 2 }, /* ASR-2020S SO-DIMM PCI-X ZCR (Terminator) */
+/* { 0x9005, 0x0286, 0x9005, 0x028c, aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2230S PCI-X ", 2 }, */ /* ASR-2230S PCI-X (Lancer pre-production) */
+ { 0x9005, 0x0285, 0x9005, 0x0290, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2410SA SATA ", 1 }, /* AAR-2410SA PCI SATA 4ch (Jaguar II) */
+ { 0x9005, 0x0285, 0x1028, 0x0291, aac_rx_init, "aacraid", "DELL ", "CERC SR2 ", 1 }, /* CERC SATA RAID 2 PCI SATA 6ch (DellCorsair) */
+ { 0x9005, 0x0285, 0x9005, 0x0292, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2810SA SATA ", 1 }, /* AAR-2810SA PCI SATA 8ch (Corsair-8) */
+ { 0x9005, 0x0285, 0x9005, 0x0293, aac_rx_init, "aacraid", "ADAPTEC ", "AAR-21610SA SATA", 1 }, /* AAR-21610SA PCI SATA 16ch (Corsair-16) */
+ { 0x9005, 0x0285, 0x9005, 0x0294, aac_rx_init, "aacraid", "ADAPTEC ", "SO-DIMM SATA ZCR", 1 }, /* ESD SO-DIMM PCI-X SATA ZCR (Prowler) */
+ { 0x9005, 0x0285, 0x0E11, 0x0295, aac_rx_init, "aacraid", "ADAPTEC ", "SATA 6Channel ", 1 }, /* SATA 6Ch (Bearcat) */
- { 0x9005, 0x0285, 0x1028, 0x0287, aac_rx_init, "percraid", "DELL ", "PERC 320/DC ", 2 }, /* Perc 320/DC*/
+ { 0x9005, 0x0285, 0x1028, 0x0287, aac_rx_init, "percraid", "DELL ", "PERC 320/DC ", 2, AAC_QUIRK_31BIT }, /* Perc 320/DC*/
{ 0x1011, 0x0046, 0x9005, 0x0365, aac_sa_init, "aacraid", "ADAPTEC ", "Adaptec 5400S ", 4 }, /* Adaptec 5400S (Mustang)*/
{ 0x1011, 0x0046, 0x9005, 0x0364, aac_sa_init, "aacraid", "ADAPTEC ", "AAC-364 ", 4 }, /* Adaptec 5400S (Mustang)*/
- { 0x1011, 0x0046, 0x9005, 0x1364, aac_sa_init, "percraid", "DELL ", "PERCRAID ", 4 }, /* Dell PERC2 "Quad Channel" */
- { 0x1011, 0x0046, 0x103c, 0x10c2, aac_sa_init, "hpnraid", "HP ", "NetRAID ", 4 } /* HP NetRAID-4M */
+ { 0x1011, 0x0046, 0x9005, 0x1364, aac_sa_init, "percraid", "DELL ", "PERCRAID ", 4, AAC_QUIRK_31BIT }, /* Dell PERC2/QC */
+ { 0x1011, 0x0046, 0x103c, 0x10c2, aac_sa_init, "hpnraid", "HP ", "NetRAID ", 4 }, /* HP NetRAID-4M */
+
+ { 0x9005, 0x0285, 0x1028, PCI_ANY_ID,
+ aac_rx_init, "aacraid", "DELL ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Dell Catchall */
+ { 0x9005, 0x0285, 0x17aa, PCI_ANY_ID,
+ aac_rx_init, "aacraid", "Legend ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Legend Catchall */
+ { 0x9005, 0x0285, PCI_ANY_ID, PCI_ANY_ID,
+ aac_rx_init, "aacraid", "ADAPTEC ", "RAID ", 2, AAC_QUIRK_31BIT }, /* Adaptec Catch All */
};
#define NUM_AACTYPES (sizeof(aac_drivers) / sizeof(struct aac_driver_ident))
@@ -174,6 +185,7 @@
struct aac_dev *aac;
struct fsa_scsi_hba *fsa_dev_ptr;
char *name = NULL;
+ int ret;
printk(KERN_INFO "Red Hat/Adaptec aacraid driver (%s %s)\n", AAC_DRIVER_VERSION, AAC_DRIVER_BUILD_DATE);
@@ -194,7 +206,15 @@
if (pci_enable_device(dev))
continue;
pci_set_master(dev);
- pci_set_dma_mask(dev, 0xFFFFFFFFULL);
+ if (aac_drivers[index].quirks & AAC_QUIRK_31BIT)
+ ret = pci_set_dma_mask(dev, 0x7FFFFFFFULL);
+ else
+ ret = pci_set_dma_mask(dev, 0xFFFFFFFFULL);
+
+ if (ret) {
+ printk(KERN_WARNING "aacraid: Can't set DMA mask.\n");
+ continue;
+ }
if((dev->subsystem_vendor != aac_drivers[index].subsystem_vendor) ||
(dev->subsystem_device != aac_drivers[index].subsystem_device))
--
Mark Haverkamp <markh@osdl.org>
^ permalink raw reply [flat|nested] 4+ messages in thread