* Bug in mm series
@ 2004-02-03 10:53 Luis Miguel García
2004-02-03 21:33 ` Derek Foreman
0 siblings, 1 reply; 3+ messages in thread
From: Luis Miguel García @ 2004-02-03 10:53 UTC (permalink / raw)
To: LINUX KERNEL MAILING LIST, akpm
When I try to boot with latest mm series (such as actual rc3-mm1 or
rc2-mm2), my nforce ethernet device doesn't works. It worked in the past
with the forcedeth reverse engineered driver but now it keeps for 30 or
more seconds halted (at boot) and then the network device dosn't run.
Here is the dmesg of rc3-mm1. Do you want for me to test something? Thanks!
P.S.: The ACPI related messages are larger that in rc3.
P.S.2: If you can, CC me because i'm not subscribed to lkml.
cted 1830.250 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 904752k/917504k available (1793k kernel code, 12008k reserved,
775k data, 132k init, 0k highmem)
Calibrating delay loop... 3612.67 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2500+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1829.0785 MHz.
..... host bus clock speed is 332.0688 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040116
IOAPIC[0]: Invalid reference to IRQ 0
spurious 8259A interrupt: IRQ7.
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: disabling nForce2 Halt Disconnect and Stop Grant Disconnect
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs *16)
ACPI: PCI Interrupt Link [APC2] (IRQs 17)
ACPI: PCI Interrupt Link [APC3] (IRQs 18)
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APCE] (IRQs 16)
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
IOAPIC[0]: Set PCI routing entry (2-23 -> 0x39 -> IRQ 23 Mode:1 Active:0)
00:00:01[A] -> 2-23 -> IRQ 23
Pin 2-23 already programmed
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
IOAPIC[0]: Set PCI routing entry (2-20 -> 0x41 -> IRQ 20 Mode:1 Active:0)
00:00:02[A] -> 2-20 -> IRQ 20
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
IOAPIC[0]: Set PCI routing entry (2-22 -> 0x49 -> IRQ 22 Mode:1 Active:0)
00:00:02[B] -> 2-22 -> IRQ 22
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
IOAPIC[0]: Set PCI routing entry (2-21 -> 0x51 -> IRQ 21 Mode:1 Active:0)
00:00:02[C] -> 2-21 -> IRQ 21
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
Pin 2-20 already programmed
ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22
Pin 2-22 already programmed
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
Pin 2-21 already programmed
ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20
Pin 2-20 already programmed
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
Pin 2-22 already programmed
ACPI: PCI Interrupt Link [AP3C] enabled at IRQ 21
Pin 2-21 already programmed
ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 20
Pin 2-20 already programmed
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
IOAPIC[0]: Set PCI routing entry (2-18 -> 0x59 -> IRQ 18 Mode:1 Active:0)
00:01:06[A] -> 2-18 -> IRQ 18
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
IOAPIC[0]: Set PCI routing entry (2-19 -> 0x61 -> IRQ 19 Mode:1 Active:0)
00:01:06[B] -> 2-19 -> IRQ 19
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
IOAPIC[0]: Set PCI routing entry (2-16 -> 0x69 -> IRQ 16 Mode:1 Active:0)
00:01:06[C] -> 2-16 -> IRQ 16
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
IOAPIC[0]: Set PCI routing entry (2-17 -> 0x71 -> IRQ 17 Mode:1 Active:0)
00:01:06[D] -> 2-17 -> IRQ 17
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-18 already programmed
Pin 2-18 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 0.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 00018971
....... : physical APIC id: 00
....... : Delivery Type: 1
....... : LTS : 0
.... register #01: 00018971
....... : max redirection entries: 0001
....... : PRQ implemented: 1
....... : IO APIC version: 0071
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 1 0 0 0 1 1 71
01 000 00 1 1 0 0 0 1 1 71
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:0
IRQ2 -> 0:0
IRQ3 -> 0:0
IRQ4 -> 0:0
IRQ5 -> 0:0
IRQ6 -> 0:0
IRQ7 -> 0:0
IRQ8 -> 0:0
IRQ9 -> 0:0
IRQ10 -> 0:0
IRQ11 -> 0:0
IRQ12 -> 0:0
IRQ13 -> 0:0
IRQ14 -> 0:0
IRQ15 -> 0:0
IRQ16 -> 0:0-> 0:16
IRQ17 -> 0:0-> 0:17
IRQ18 -> 0:0-> 0:18
IRQ19 -> 0:0-> 0:19
IRQ20 -> 0:0-> 0:20
IRQ21 -> 0:0-> 0:21
IRQ22 -> 0:0-> 0:22
IRQ23 -> 0:0-> 0:23
IRQ24 -> 0:0
IRQ25 -> 0:0
IRQ26 -> 0:0
IRQ27 -> 0:0
IRQ28 -> 0:0
IRQ29 -> 0:0
IRQ30 -> 0:0
IRQ31 -> 0:0
IRQ32 -> 0:0
IRQ33 -> 0:0
IRQ34 -> 0:0
IRQ35 -> 0:0
IRQ36 -> 0:0
IRQ37 -> 0:0
IRQ38 -> 0:0
IRQ39 -> 0:0
IRQ40 -> 0:0
IRQ41 -> 0:0
IRQ42 -> 0:0
IRQ43 -> 0:0
IRQ44 -> 0:0
IRQ45 -> 0:0
IRQ46 -> 0:0
IRQ47 -> 0:0
IRQ48 -> 0:0
IRQ49 -> 0:0
IRQ50 -> 0:0
IRQ51 -> 0:0
IRQ52 -> 0:0
IRQ53 -> 0:0
IRQ54 -> 0:0
IRQ55 -> 0:0
IRQ56 -> 0:0
IRQ57 -> 0:0
IRQ58 -> 0:0
IRQ59 -> 0:0
IRQ60 -> 0:0
IRQ61 -> 0:0
IRQ62 -> 0:0
IRQ63 -> 0:0
IRQ64 -> 0:0
IRQ65 -> 0:0
IRQ66 -> 0:0
IRQ67 -> 0:0
IRQ68 -> 0:0
IRQ69 -> 0:0
IRQ70 -> 0:0
IRQ71 -> 0:0
IRQ72 -> 0:0
IRQ73 -> 0:0
IRQ74 -> 0:0
IRQ75 -> 0:0
IRQ76 -> 0:0
IRQ77 -> 0:0
IRQ78 -> 0:0
IRQ79 -> 0:0
IRQ80 -> 0:0
IRQ81 -> 0:0
IRQ82 -> 0:0
IRQ83 -> 0:0
IRQ84 -> 0:0
IRQ85 -> 0:0
IRQ86 -> 0:0
IRQ87 -> 0:0
IRQ88 -> 0:0
IRQ89 -> 0:0
IRQ90 -> 0:0
IRQ91 -> 0:0
IRQ92 -> 0:0
IRQ93 -> 0:0
IRQ94 -> 0:0
IRQ95 -> 0:0
IRQ96 -> 0:0
IRQ97 -> 0:0
IRQ98 -> 0:0
IRQ99 -> 0:0
IRQ100 -> 0:0
IRQ101 -> 0:0
IRQ102 -> 0:0
IRQ103 -> 0:0
IRQ104 -> 0:0
IRQ105 -> 0:0
IRQ106 -> 0:0
IRQ107 -> 0:0
IRQ108 -> 0:0
IRQ109 -> 0:0
IRQ110 -> 0:0
IRQ111 -> 0:0
IRQ112 -> 0:0
IRQ113 -> 0:0
IRQ114 -> 0:0
IRQ115 -> 0:0
IRQ116 -> 0:0
IRQ117 -> 0:0
IRQ118 -> 0:0
IRQ119 -> 0:0
IRQ120 -> 0:0
IRQ121 -> 0:0
IRQ122 -> 0:0
IRQ123 -> 0:0
IRQ124 -> 0:0
IRQ125 -> 0:0
IRQ126 -> 0:0
IRQ127 -> 0:0
IRQ128 -> 0:0
IRQ129 -> 0:0
IRQ130 -> 0:0
IRQ131 -> 0:0
IRQ132 -> 0:0
IRQ133 -> 0:0
IRQ134 -> 0:0
IRQ135 -> 0:0
IRQ136 -> 0:0
IRQ137 -> 0:0
IRQ138 -> 0:0
IRQ139 -> 0:0
IRQ140 -> 0:0
IRQ141 -> 0:0
IRQ142 -> 0:0
IRQ143 -> 0:0
IRQ144 -> 0:0
IRQ145 -> 0:0
IRQ146 -> 0:0
IRQ147 -> 0:0
IRQ148 -> 0:0
IRQ149 -> 0:0
IRQ150 -> 0:0
IRQ151 -> 0:0
IRQ152 -> 0:0
IRQ153 -> 0:0
IRQ154 -> 0:0
IRQ155 -> 0:0
IRQ156 -> 0:0
IRQ157 -> 0:0
IRQ158 -> 0:0
IRQ159 -> 0:0
IRQ160 -> 0:0
IRQ161 -> 0:0
IRQ162 -> 0:0
IRQ163 -> 0:0
IRQ164 -> 0:0
IRQ165 -> 0:0
IRQ166 -> 0:0
IRQ167 -> 0:0
IRQ168 -> 0:0
IRQ169 -> 0:0
IRQ170 -> 0:0
IRQ171 -> 0:0
IRQ172 -> 0:0
IRQ173 -> 0:0
IRQ174 -> 0:0
IRQ175 -> 0:0
IRQ176 -> 0:0
IRQ177 -> 0:0
IRQ178 -> 0:0
IRQ179 -> 0:0
IRQ180 -> 0:0
IRQ181 -> 0:0
IRQ182 -> 0:0
IRQ183 -> 0:0
IRQ184 -> 0:0
IRQ185 -> 0:0
IRQ186 -> 0:0
IRQ187 -> 0:0
IRQ188 -> 0:0
IRQ189 -> 0:0
IRQ190 -> 0:0
IRQ191 -> 0:0
IRQ192 -> 0:0
IRQ193 -> 0:0
IRQ194 -> 0:0
IRQ195 -> 0:0
IRQ196 -> 0:0
IRQ197 -> 0:0
IRQ198 -> 0:0
IRQ199 -> 0:0
IRQ200 -> 0:0
IRQ201 -> 0:0
IRQ202 -> 0:0
IRQ203 -> 0:0
IRQ204 -> 0:0
IRQ205 -> 0:0
IRQ206 -> 0:0
IRQ207 -> 0:0
IRQ208 -> 0:0
IRQ209 -> 0:0
IRQ210 -> 0:0
IRQ211 -> 0:0
IRQ212 -> 0:0
IRQ213 -> 0:0
IRQ214 -> 0:0
IRQ215 -> 0:0
IRQ216 -> 0:0
IRQ217 -> 0:0
IRQ218 -> 0:0
IRQ219 -> 0:0
IRQ220 -> 0:0
IRQ221 -> 0:0
IRQ222 -> 0:0
IRQ223 -> 0:0
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (54 C)
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.12
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST380023A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-ST GCE-8520B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63,
UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > p3 p4
hdc: ATAPI 40X CD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda4, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda4) for (hda4)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding 498004k swap on /dev/hda3. Priority:-1 extents:1
SCSI subsystem initialized
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.19.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 0147b:1c00 bound to 0000:00:04.0
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 128M @ 0xd0000000
Linux video capture interface: v1.00
bttv: driver version 0.9.12 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 0000:01:08.0, irq: 16, latency: 32, mmio: 0xd8000000
bttv0: using: Prolink PixelView PlayTV pro [card=37,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=2
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: chip found @ 0xc2
tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
tuner: type forced to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
[insmod]
tuner: type already set (2)
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49329 usecs
intel8x0: clocking to 48000
ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 20, pci mem f8a28000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 22, pci mem f8a2a000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 21, pci mem f8a2c000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
hub 1-0:1.0: connect-debounce failed, port 1 disabled
hub 1-0:1.0: new USB device on port 1, assigned address 2
usb 1-1: control timeout on ep0out
ohci_hcd 0000:00:02.0: Unlink after no-IRQ? Different ACPI or APIC
settings may help.
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: Bug in mm series
2004-02-03 10:53 Bug in mm series Luis Miguel García
@ 2004-02-03 21:33 ` Derek Foreman
0 siblings, 0 replies; 3+ messages in thread
From: Derek Foreman @ 2004-02-03 21:33 UTC (permalink / raw)
To: Luis Miguel García; +Cc: LINUX KERNEL MAILING LIST, akpm
On Tue, 3 Feb 2004, [ISO-8859-1] Luis Miguel García wrote:
> When I try to boot with latest mm series (such as actual rc3-mm1 or
> rc2-mm2), my nforce ethernet device doesn't works. It worked in the past
> with the forcedeth reverse engineered driver but now it keeps for 30 or
> more seconds halted (at boot) and then the network device dosn't run.
>
> Here is the dmesg of rc3-mm1. Do you want for me to test something? Thanks!
>
> P.S.: The ACPI related messages are larger that in rc3.
My e100 on an nforce2 won't work in rc3-mm1.
The "acpi=off" boot parameter makes it go.
^ permalink raw reply [flat|nested] 3+ messages in thread
* RE: Bug in mm series
@ 2004-02-04 0:51 Li, Shaohua
0 siblings, 0 replies; 3+ messages in thread
From: Li, Shaohua @ 2004-02-04 0:51 UTC (permalink / raw)
To: Luis Miguel García; +Cc: LINUX KERNEL MAILING LIST, akpm
Hi,
Is this really an ACPI error? I noticed below message:
>IOAPIC[0]: Invalid reference to IRQ 0
> number of IO-APIC #2 registers: 0
It sounds like IOAPIC can't be initialized correctly.
> -----Original Message-----
> From: linux-kernel-owner@vger.kernel.org [mailto:linux-kernel-
> owner@vger.kernel.org] On Behalf Of Luis Miguel García
> Sent: 2004年2月3日 18:53
> To: LINUX KERNEL MAILING LIST; akpm@digeo.com
> Subject: Bug in mm series
>
> When I try to boot with latest mm series (such as actual rc3-mm1 or
> rc2-mm2), my nforce ethernet device doesn't works. It worked in the past
> with the forcedeth reverse engineered driver but now it keeps for 30 or
> more seconds halted (at boot) and then the network device dosn't run.
>
> Here is the dmesg of rc3-mm1. Do you want for me to test something? Thanks!
>
> P.S.: The ACPI related messages are larger that in rc3.
>
> P.S.2: If you can, CC me because i'm not subscribed to lkml.
>
>
> cted 1830.250 MHz processor.
> Using tsc for high-res timesource
> Console: colour VGA+ 80x25
> Memory: 904752k/917504k available (1793k kernel code, 12008k reserved,
> 775k data, 132k init, 0k highmem)
> Calibrating delay loop... 3612.67 BogoMIPS
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: AMD Athlon(tm) XP 2500+ stepping 00
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> enabled ExtINT on CPU#0
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Using local APIC timer interrupts.
> calibrating APIC timer ...
> ..... CPU clock speed is 1829.0785 MHz.
> ..... host bus clock speed is 332.0688 MHz.
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=2
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20040116
> IOAPIC[0]: Invalid reference to IRQ 0
> spurious 8259A interrupt: IRQ7.
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (00:00)
> PCI: Probing PCI hardware (bus 00)
> PCI: disabling nForce2 Halt Disconnect and Stop Grant Disconnect
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
> ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [APC1] (IRQs *16)
> ACPI: PCI Interrupt Link [APC2] (IRQs 17)
> ACPI: PCI Interrupt Link [APC3] (IRQs 18)
> ACPI: PCI Interrupt Link [APC4] (IRQs *19)
> ACPI: PCI Interrupt Link [APCE] (IRQs 16)
> ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCS] (IRQs *23)
> ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22)
> ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
> IOAPIC[0]: Set PCI routing entry (2-23 -> 0x39 -> IRQ 23 Mode:1 Active:0)
> 00:00:01[A] -> 2-23 -> IRQ 23
> Pin 2-23 already programmed
> ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
> IOAPIC[0]: Set PCI routing entry (2-20 -> 0x41 -> IRQ 20 Mode:1 Active:0)
> 00:00:02[A] -> 2-20 -> IRQ 20
> ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
> IOAPIC[0]: Set PCI routing entry (2-22 -> 0x49 -> IRQ 22 Mode:1 Active:0)
> 00:00:02[B] -> 2-22 -> IRQ 22
> ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
> IOAPIC[0]: Set PCI routing entry (2-21 -> 0x51 -> IRQ 21 Mode:1 Active:0)
> 00:00:02[C] -> 2-21 -> IRQ 21
> ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
> Pin 2-20 already programmed
> ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22
> Pin 2-22 already programmed
> ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
> Pin 2-21 already programmed
> ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20
> Pin 2-20 already programmed
> ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
> Pin 2-22 already programmed
> ACPI: PCI Interrupt Link [AP3C] enabled at IRQ 21
> Pin 2-21 already programmed
> ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 20
> Pin 2-20 already programmed
> ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
> IOAPIC[0]: Set PCI routing entry (2-18 -> 0x59 -> IRQ 18 Mode:1 Active:0)
> 00:01:06[A] -> 2-18 -> IRQ 18
> ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
> IOAPIC[0]: Set PCI routing entry (2-19 -> 0x61 -> IRQ 19 Mode:1 Active:0)
> 00:01:06[B] -> 2-19 -> IRQ 19
> ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
> IOAPIC[0]: Set PCI routing entry (2-16 -> 0x69 -> IRQ 16 Mode:1 Active:0)
> 00:01:06[C] -> 2-16 -> IRQ 16
> ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
> IOAPIC[0]: Set PCI routing entry (2-17 -> 0x71 -> IRQ 17 Mode:1 Active:0)
> 00:01:06[D] -> 2-17 -> IRQ 17
> Pin 2-19 already programmed
> Pin 2-16 already programmed
> Pin 2-17 already programmed
> Pin 2-18 already programmed
> Pin 2-16 already programmed
> Pin 2-17 already programmed
> Pin 2-18 already programmed
> Pin 2-19 already programmed
> Pin 2-17 already programmed
> Pin 2-18 already programmed
> Pin 2-19 already programmed
> Pin 2-16 already programmed
> Pin 2-18 already programmed
> Pin 2-19 already programmed
> Pin 2-16 already programmed
> Pin 2-17 already programmed
> Pin 2-18 already programmed
> Pin 2-18 already programmed
> Pin 2-18 already programmed
> Pin 2-18 already programmed
> Pin 2-19 already programmed
> number of MP IRQ sources: 16.
> number of IO-APIC #2 registers: 0.
> testing the IO APIC.......................
> IO APIC #2......
> .... register #00: 00018971
> ....... : physical APIC id: 00
> ....... : Delivery Type: 1
> ....... : LTS : 0
> .... register #01: 00018971
> ....... : max redirection entries: 0001
> ....... : PRQ implemented: 1
> ....... : IO APIC version: 0071
> .... IRQ redirection table:
> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
> 00 000 00 1 1 0 0 0 1 1 71
> 01 000 00 1 1 0 0 0 1 1 71
> IRQ to pin mappings:
> IRQ0 -> 0:0
> IRQ1 -> 0:0
> IRQ2 -> 0:0
> IRQ3 -> 0:0
> IRQ4 -> 0:0
> IRQ5 -> 0:0
> IRQ6 -> 0:0
> IRQ7 -> 0:0
> IRQ8 -> 0:0
> IRQ9 -> 0:0
> IRQ10 -> 0:0
> IRQ11 -> 0:0
> IRQ12 -> 0:0
> IRQ13 -> 0:0
> IRQ14 -> 0:0
> IRQ15 -> 0:0
> IRQ16 -> 0:0-> 0:16
> IRQ17 -> 0:0-> 0:17
> IRQ18 -> 0:0-> 0:18
> IRQ19 -> 0:0-> 0:19
> IRQ20 -> 0:0-> 0:20
> IRQ21 -> 0:0-> 0:21
> IRQ22 -> 0:0-> 0:22
> IRQ23 -> 0:0-> 0:23
> IRQ24 -> 0:0
> IRQ25 -> 0:0
> IRQ26 -> 0:0
> IRQ27 -> 0:0
> IRQ28 -> 0:0
> IRQ29 -> 0:0
> IRQ30 -> 0:0
> IRQ31 -> 0:0
> IRQ32 -> 0:0
> IRQ33 -> 0:0
> IRQ34 -> 0:0
> IRQ35 -> 0:0
> IRQ36 -> 0:0
> IRQ37 -> 0:0
> IRQ38 -> 0:0
> IRQ39 -> 0:0
> IRQ40 -> 0:0
> IRQ41 -> 0:0
> IRQ42 -> 0:0
> IRQ43 -> 0:0
> IRQ44 -> 0:0
> IRQ45 -> 0:0
> IRQ46 -> 0:0
> IRQ47 -> 0:0
> IRQ48 -> 0:0
> IRQ49 -> 0:0
> IRQ50 -> 0:0
> IRQ51 -> 0:0
> IRQ52 -> 0:0
> IRQ53 -> 0:0
> IRQ54 -> 0:0
> IRQ55 -> 0:0
> IRQ56 -> 0:0
> IRQ57 -> 0:0
> IRQ58 -> 0:0
> IRQ59 -> 0:0
> IRQ60 -> 0:0
> IRQ61 -> 0:0
> IRQ62 -> 0:0
> IRQ63 -> 0:0
> IRQ64 -> 0:0
> IRQ65 -> 0:0
> IRQ66 -> 0:0
> IRQ67 -> 0:0
> IRQ68 -> 0:0
> IRQ69 -> 0:0
> IRQ70 -> 0:0
> IRQ71 -> 0:0
> IRQ72 -> 0:0
> IRQ73 -> 0:0
> IRQ74 -> 0:0
> IRQ75 -> 0:0
> IRQ76 -> 0:0
> IRQ77 -> 0:0
> IRQ78 -> 0:0
> IRQ79 -> 0:0
> IRQ80 -> 0:0
> IRQ81 -> 0:0
> IRQ82 -> 0:0
> IRQ83 -> 0:0
> IRQ84 -> 0:0
> IRQ85 -> 0:0
> IRQ86 -> 0:0
> IRQ87 -> 0:0
> IRQ88 -> 0:0
> IRQ89 -> 0:0
> IRQ90 -> 0:0
> IRQ91 -> 0:0
> IRQ92 -> 0:0
> IRQ93 -> 0:0
> IRQ94 -> 0:0
> IRQ95 -> 0:0
> IRQ96 -> 0:0
> IRQ97 -> 0:0
> IRQ98 -> 0:0
> IRQ99 -> 0:0
> IRQ100 -> 0:0
> IRQ101 -> 0:0
> IRQ102 -> 0:0
> IRQ103 -> 0:0
> IRQ104 -> 0:0
> IRQ105 -> 0:0
> IRQ106 -> 0:0
> IRQ107 -> 0:0
> IRQ108 -> 0:0
> IRQ109 -> 0:0
> IRQ110 -> 0:0
> IRQ111 -> 0:0
> IRQ112 -> 0:0
> IRQ113 -> 0:0
> IRQ114 -> 0:0
> IRQ115 -> 0:0
> IRQ116 -> 0:0
> IRQ117 -> 0:0
> IRQ118 -> 0:0
> IRQ119 -> 0:0
> IRQ120 -> 0:0
> IRQ121 -> 0:0
> IRQ122 -> 0:0
> IRQ123 -> 0:0
> IRQ124 -> 0:0
> IRQ125 -> 0:0
> IRQ126 -> 0:0
> IRQ127 -> 0:0
> IRQ128 -> 0:0
> IRQ129 -> 0:0
> IRQ130 -> 0:0
> IRQ131 -> 0:0
> IRQ132 -> 0:0
> IRQ133 -> 0:0
> IRQ134 -> 0:0
> IRQ135 -> 0:0
> IRQ136 -> 0:0
> IRQ137 -> 0:0
> IRQ138 -> 0:0
> IRQ139 -> 0:0
> IRQ140 -> 0:0
> IRQ141 -> 0:0
> IRQ142 -> 0:0
> IRQ143 -> 0:0
> IRQ144 -> 0:0
> IRQ145 -> 0:0
> IRQ146 -> 0:0
> IRQ147 -> 0:0
> IRQ148 -> 0:0
> IRQ149 -> 0:0
> IRQ150 -> 0:0
> IRQ151 -> 0:0
> IRQ152 -> 0:0
> IRQ153 -> 0:0
> IRQ154 -> 0:0
> IRQ155 -> 0:0
> IRQ156 -> 0:0
> IRQ157 -> 0:0
> IRQ158 -> 0:0
> IRQ159 -> 0:0
> IRQ160 -> 0:0
> IRQ161 -> 0:0
> IRQ162 -> 0:0
> IRQ163 -> 0:0
> IRQ164 -> 0:0
> IRQ165 -> 0:0
> IRQ166 -> 0:0
> IRQ167 -> 0:0
> IRQ168 -> 0:0
> IRQ169 -> 0:0
> IRQ170 -> 0:0
> IRQ171 -> 0:0
> IRQ172 -> 0:0
> IRQ173 -> 0:0
> IRQ174 -> 0:0
> IRQ175 -> 0:0
> IRQ176 -> 0:0
> IRQ177 -> 0:0
> IRQ178 -> 0:0
> IRQ179 -> 0:0
> IRQ180 -> 0:0
> IRQ181 -> 0:0
> IRQ182 -> 0:0
> IRQ183 -> 0:0
> IRQ184 -> 0:0
> IRQ185 -> 0:0
> IRQ186 -> 0:0
> IRQ187 -> 0:0
> IRQ188 -> 0:0
> IRQ189 -> 0:0
> IRQ190 -> 0:0
> IRQ191 -> 0:0
> IRQ192 -> 0:0
> IRQ193 -> 0:0
> IRQ194 -> 0:0
> IRQ195 -> 0:0
> IRQ196 -> 0:0
> IRQ197 -> 0:0
> IRQ198 -> 0:0
> IRQ199 -> 0:0
> IRQ200 -> 0:0
> IRQ201 -> 0:0
> IRQ202 -> 0:0
> IRQ203 -> 0:0
> IRQ204 -> 0:0
> IRQ205 -> 0:0
> IRQ206 -> 0:0
> IRQ207 -> 0:0
> IRQ208 -> 0:0
> IRQ209 -> 0:0
> IRQ210 -> 0:0
> IRQ211 -> 0:0
> IRQ212 -> 0:0
> IRQ213 -> 0:0
> IRQ214 -> 0:0
> IRQ215 -> 0:0
> IRQ216 -> 0:0
> IRQ217 -> 0:0
> IRQ218 -> 0:0
> IRQ219 -> 0:0
> IRQ220 -> 0:0
> IRQ221 -> 0:0
> IRQ222 -> 0:0
> IRQ223 -> 0:0
> .................................... done.
> PCI: Using ACPI for IRQ routing
> PCI: if you experience problems, try using option 'pci=noacpi' or even
> 'acpi=off'
> devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
> devfs: boot_options: 0x0
> Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> ACPI: Power Button (FF) [PWRF]
> ACPI: Fan [FAN] (on)
> ACPI: Processor [CPU0] (supports C1)
> ACPI: Thermal Zone [THRM] (54 C)
> pty: 256 Unix98 ptys configured
> Real Time Clock Driver v1.12
> Using anticipatory io scheduler
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> NFORCE2: IDE controller at PCI slot 0000:00:09.0
> NFORCE2: chipset revision 162
> NFORCE2: not 100% native mode: will probe irqs later
> NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST380023A, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: HL-DT-ST GCE-8520B, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 128KiB
> hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63,
> UDMA(100)
> /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > p3 p4
> hdc: ATAPI 40X CD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> mice: PS/2 mouse device common for all mice
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
> serio: i8042 KBD port at 0x60,0x64 irq 1
> input: AT Translated Set 2 keyboard on isa0060/serio0
> NET: Registered protocol family 2
> IP: routing cache hash table of 8192 buckets, 64Kbytes
> TCP: Hash tables configured (established 262144 bind 65536)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> found reiserfs format "3.6" with standard journal
> Reiserfs journal params: device hda4, size 8192, journal first block 18,
> max trans len 1024, max batch 900, max commit age 30, max trans age 30
> reiserfs: checking transaction log (hda4) for (hda4)
> Using r5 hash to sort names
> VFS: Mounted root (reiserfs filesystem) readonly.
> Freeing unused kernel memory: 132k freed
> Adding 498004k swap on /dev/hda3. Priority:-1 extents:1
> SCSI subsystem initialized
> forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.19.
> PCI: Setting latency timer of device 0000:00:04.0 to 64
> eth0: forcedeth.c: subsystem: 0147b:1c00 bound to 0000:00:04.0
> Linux agpgart interface v0.100 (c) Dave Jones
> agpgart: Detected NVIDIA nForce2 chipset
> agpgart: Maximum main memory to use for agp memory: 816M
> agpgart: AGP aperture is 128M @ 0xd0000000
> Linux video capture interface: v1.00
> bttv: driver version 0.9.12 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> bttv0: Bt878 (rev 2) at 0000:01:08.0, irq: 16, latency: 32, mmio:
> 0xd8000000
> bttv0: using: Prolink PixelView PlayTV pro [card=37,insmod option]
> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> bttv0: using tuner=2
> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> tuner: chip found @ 0xc2
> tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
> tuner: type forced to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
> [insmod]
> tuner: type already set (2)
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: PLL: 28636363 => 35468950 .. ok
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> intel8x0_measure_ac97_clock: measured 49329 usecs
> intel8x0: clocking to 48000
> ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> ohci_hcd: block sizes: ed 64 td 64
> ohci_hcd 0000:00:02.0: OHCI Host Controller
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> ohci_hcd 0000:00:02.0: irq 20, pci mem f8a28000
> ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> ohci_hcd 0000:00:02.1: OHCI Host Controller
> PCI: Setting latency timer of device 0000:00:02.1 to 64
> ohci_hcd 0000:00:02.1: irq 22, pci mem f8a2a000
> ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> ehci_hcd 0000:00:02.2: EHCI Host Controller
> PCI: Setting latency timer of device 0000:00:02.2 to 64
> ehci_hcd 0000:00:02.2: irq 21, pci mem f8a2c000
> ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
> PCI: cache line size of 64 is not supported by device 0000:00:02.2
> ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 6 ports detected
> hub 1-0:1.0: connect-debounce failed, port 1 disabled
> hub 1-0:1.0: new USB device on port 1, assigned address 2
> usb 1-1: control timeout on ep0out
> ohci_hcd 0000:00:02.0: Unlink after no-IRQ? Different ACPI or APIC
> settings may help.
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-02-04 0:52 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-02-03 10:53 Bug in mm series Luis Miguel García
2004-02-03 21:33 ` Derek Foreman
-- strict thread matches above, loose matches on Subject: below --
2004-02-04 0:51 Li, Shaohua
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox