From: David Ford <david+challenge-response@blue-labs.org>
To: linux-kernel mailing list <linux-kernel@vger.kernel.org>
Subject: SONY SMO-F551, non-functional for a loong time :)
Date: Sun, 22 Feb 2004 18:23:00 -0500 [thread overview]
Message-ID: <403939D4.9020804@blue-labs.org> (raw)
For the last couple of years, this MO drive (I have several) has been
unusable. It used to lock up the machine if I had a disc inside it when
I booted, but that was late in 2.5, and now with 2.6.3, it no longer
hangs the machine, however, it's still not usable.
I'd love to get this bugger working, I used to use it a long long time
ago in 2.4 kernels. Any suggestions?
David
--
bootup stuff:
sym0: <875> rev 0x4 at pci 0000:01:0b.0 irq 209
sym0: Symbios NVRAM, ID 15, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18f
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
Vendor: SONY Model: SMO-F551 Rev: 1.14
Type: Optical Device ANSI SCSI revision: 02
sym0:4:0: tagged command queuing enabled, command queue depth 16.
libata version 1.00 loaded.
st: Version 20040122, fixed bufsize 32768, s/g segs 256
sym0:4: FAST-10 SCSI 5.0 MB/s ST (200.0 ns, offset 15)
sda: Unit Not Ready, sense:
Current : sense key Hardware Error
ASC=40 ASCQ=86
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Hardware Error
ASC=40 ASCQ=86
sda: Write Protect is off
sda: Mode Sense: 5b 03 10 08
SCSI device sda: drive cache: write back
SCSI error: host 0 id 4 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 4
sda: Unit Not Ready, sense:
Current : sense key Hardware Error
ASC=40 ASCQ=86
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Hardware Error
ASC=40 ASCQ=86
sda: Write Protect is off
sda: Mode Sense: 5b 03 10 08
SCSI device sda: drive cache: write back
sda: Unit Not Ready, sense:
Current : sense key Hardware Error
ASC=40 ASCQ=86
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Hardware Error
ASC=40 ASCQ=86
sda: Write Protect is off
sda: Mode Sense: 5b 03 10 08
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target4/lun0:<3>Buffer I/O error on device sda,
logical block 0
Buffer I/O error on device sda, logical block 0
unable to read partition table
/dev/scsi/host0/bus0/target4/lun0:<3>Buffer I/O error on device sda,
logical block 0
unable to read partition table
Attached scsi removable disk sda at scsi0, channel 0, id 4, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 6
Attached scsi generic sg1 at scsi0, channel 0, id 4, lun 0, type 7
# fdisk /dev/sda
Unable to read /dev/sda
# dmesg -c
SCSI error: host 0 id 4 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 4
sda: Unit Not Ready, sense:
Current : sense key Hardware Error
ASC=40 ASCQ=86
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Hardware Error
ASC=40 ASCQ=86
sda: Write Protect is off
sda: Mode Sense: 5b 03 10 08
SCSI device sda: drive cache: write back
sda: Unit Not Ready, sense:
Current : sense key Hardware Error
ASC=40 ASCQ=86
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Hardware Error
ASC=40 ASCQ=86
sda: Write Protect is off
sda: Mode Sense: 5b 03 10 08
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target4/lun0:<3>Buffer I/O error on device sda,
logical block 0
Buffer I/O error on device sda, logical block 0
unable to read partition table
Buffer I/O error on device sda, logical block 0
Buffer I/O error on device sda, logical block 1
Buffer I/O error on device sda, logical block 2
Buffer I/O error on device sda, logical block 3
Buffer I/O error on device sda, logical block 4
Buffer I/O error on device sda, logical block 5
Buffer I/O error on device sda, logical block 6
Buffer I/O error on device sda, logical block 7
Buffer I/O error on device sda, logical block 8
Buffer I/O error on device sda, logical block 9
Buffer I/O error on device sda, logical block 10
Buffer I/O error on device sda, logical block 11
Buffer I/O error on device sda, logical block 12
Buffer I/O error on device sda, logical block 13
Buffer I/O error on device sda, logical block 14
Buffer I/O error on device sda, logical block 15
next reply other threads:[~2004-02-22 23:23 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-02-22 23:23 David Ford [this message]
2004-02-22 23:42 ` SONY SMO-F551, non-functional for a loong time :) Steve McIntyre
2004-02-23 0:23 ` David Ford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=403939D4.9020804@blue-labs.org \
--to=david+challenge-response@blue-labs.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox