hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

[Bob Gill]

Hi.  I recently built 2.6.6-rc3-bk8.  The boot process stalls with 
ide-cd: cmd 0x5a timed out
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
ide-cd: cmd 0x3 timed out
...
There are no problems booting 2.6.6-rc3-bk6.
My system: FC2-test3.
When booting from 2.6.6-rc3-bk6, I get the following:
(from cat /proc/ioports)
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1080-109f : 0000:00:02.1
e000-e0ff : 0000:00:03.0
  e000-e0ff : sis900
e400-e41f : 0000:00:09.0
  e400-e41f : EMU10K1
e800-e807 : 0000:00:09.1
ec00-ec7f : 0000:00:0d.0
f000-f00f : 0000:00:02.5
  f000-f007 : ide0
  f008-f00f : ide1

from /proc/interrupts:
           CPU0
  0:    1580849          XT-PIC  timer
  1:       4012          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  5:          6          XT-PIC  bttv0
  9:       9680          XT-PIC  acpi, EMU10K1, ohci1394
 10:     114470          XT-PIC  ohci_hcd, nvidia
 11:        562          XT-PIC  ohci_hcd, eth0
 12:      39542          XT-PIC  i8042
 14:      19181          XT-PIC  ide0
 15:      21677          XT-PIC  ide1
NMI:          0
LOC:    1580793
ERR:          0
MIS:          0

I didn't see anything in /Documentation.  Besides running FC2-t3
(updated with yum), I have /sys and /udev (hotplug from 2004_04_01 and
udev-025) installed.  On my system /dev/hdc is a Sony DVD drive, and is
not /boot or /.  
I can still boot 2.6.6-rc3-bk6 without problems.  Please email me for
more information as I'm not on the list.
TIA,
Bob

Re: hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

[Bartlomiej Zolnierkiewicz]

zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

On Thursday 06 of May 2004 22:29, Bob Gill wrote:
> Hi.  I recently built 2.6.6-rc3-bk8.  The boot process stalls with
> ide-cd: cmd 0x5a timed out
> hdc: lost interrupt.
> hdc: lost interrupt.
> hdc: lost interrupt.
> hdc: lost interrupt.
> ide-cd: cmd 0x3 timed out
> ...
> There are no problems booting 2.6.6-rc3-bk6.

Re: hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

[Bob Gill]

>zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

OK.  My APIC is a SiS961.  
I can't send data from 2.6.6-rc3-bk8, but from 2.6.6-rc3-bk6,
/proc/acpi gives:
(/proc/acpi/processor/CPU0)
processor id:            0
acpi id:                 0
bus mastering control:   yes
power management:        no
throttling control:      no
limit interface:         no
<not supported>
active state:            C1
default state:           C1
bus master activity:     00000000
states:
   *C1:                  promotion[--] demotion[--] latency[000]
usage[00000000]
    C2:                  <not supported>
    C3:                  <not supported>
<not supported>

cat /proc/acpi/sleep shows:
S0 S1 S4 S5
cat /proc/ide/sis shows:
SiS 5513 Ultra 100 chipset
--------------- Primary Channel ---------------- Secondary Channel
-------------
Channel Status: On                               On
Operation Mode: Compatible                       Compatible
Cable Type:     80 pins                          80 pins
Prefetch Count: 512                              512
Drive 0:        Postwrite Enabled                Postwrite Disabled
                Prefetch  Enabled                Prefetch  Disabled
                UDMA Enabled                     UDMA Enabled
                UDMA Cycle Time    3 CLK         UDMA Cycle Time    6
CLK
                Data Active Time   3 PCICLK      Data Active Time   3
PCICLK
                Data Recovery Time 1 PCICLK      Data Recovery Time 1
PCICLK
Drive 1:        Postwrite Enabled                Postwrite Disabled
                Prefetch  Enabled                Prefetch  Disabled
                UDMA Enabled                     UDMA Disabled
                UDMA Cycle Time    2 CLK         UDMA Cycle Time   
Reserved
                Data Active Time   3 PCICLK      Data Active Time   3
PCICLK
                Data Recovery Time 1 PCICLK      Data Recovery Time 3
PCICLK


... I don't know if any of this is helpful.  The IRQ and IO address
assignments (sent with my first email) are from 2.6.6-rc3-bk6.  

Thanks,
Bob

Re: hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

[Gabriele Giorgetti]

Bob Gill wrote:
> Hi.  I recently built 2.6.6-rc3-bk8.  The boot process stalls with 
> ide-cd: cmd 0x5a timed out
> hdc: lost interrupt.
> hdc: lost interrupt.
> hdc: lost interrupt.
> hdc: lost interrupt.
> ide-cd: cmd 0x3 timed out
> ...

Same thing here with a SiS 962/963 and Linux 2.6.6.
2.6.5 was working just fine.
Also the acpi=noirq workaround works for me as well.


IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]

SiS 962/963 MuTIOL IDE UDMA133 controller