Re: [2.6.7-rc1-mm1] cant mount reiserfs using -o barrier=flush

[Gunther Persoons <gunther_persoons@spymac.com>]

Hey,

<>Following warnings only come when i mount with the option 
barrier=flush, i have never seen them before.
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }

Also this line clearly states that barrier doesn't work on my harddrive 
although it's and IDE drive.
hda: barrier support doesn't work.


Ed Tomlinson wrote:

>Hi
>
>Think this is not just a barrier problem (unless barrier is the default).
>One if my two drives gets the error below during operation.
>The drive is the root drive and is mounted with defaults.  2.6.6-mm4
>was the last kernel booted on this box.   The 2.6.7-rc1-mm1 was compiled
>with 2.95 with the following fs options:
>
>CONFIG_EXT2_FS=y
># CONFIG_EXT2_FS_XATTR is not set
>CONFIG_EXT3_FS=m
># CONFIG_EXT3_FS_XATTR is not set
>CONFIG_JBD=m
># CONFIG_JBD_DEBUG is not set
>CONFIG_REISERFS_FS=y
># CONFIG_REISERFS_CHECK is not set
># CONFIG_REISERFS_PROC_INFO is not set
># CONFIG_REISERFS_FS_XATTR is not set
># CONFIG_JFS_FS is not set
># CONFIG_XFS_FS is not set
># CONFIG_MINIX_FS is not set
># CONFIG_ROMFS_FS is not set
># CONFIG_QUOTA is not set
># CONFIG_AUTOFS_FS is not set
>CONFIG_AUTOFS4_FS=m
>
>hda reports:
>root@bert:/usr/src/linux# hdparm -iI /dev/hda
>
>/dev/hda:
>
> Model=WDC AC26400R, FwRev=15.01J15, SerialNo=WD-WM6271600165
> Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
> RawCHS=13328/15/63, TrkSize=57600, SectSize=600, ECCbytes=40
> BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
> CurCHS=13328/15/63, CurSects=12594960, LBA=yes, LBAsects=12594960
> IORDY=on/off, tPIO={min:160,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes:  pio0 pio1 pio2 pio3 pio4
> DMA modes:  mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4
> AdvancedPM=no WriteCache=enabled
> Drive conforms to: device does not report version:  1 2 3 4
>
> * signifies the current active mode
>
>
>ATA device, with non-removable media
>        Model Number:       WDC AC26400R
>        Serial Number:      WD-WM6271600165
>        Firmware Revision:  15.01J15
>Standards:
>        Supported: 4 3 2 1
>        Likely used: 4
>Configuration:
>        Logical         max     current
>        cylinders       13328   13328
>        heads           15      15
>        sectors/track   63      63
>        --
>        bytes/track: 57600      bytes/sector: 600
>        CHS current addressable sectors:   12594960
>        LBA    user addressable sectors:   12594960
>        device size with M = 1024*1024:        6149 MBytes
>        device size with M = 1000*1000:        6448 MBytes (6 GB)
>Capabilities:
>        LBA, IORDY(can be disabled)
>        Buffer size: 512.0kB    bytes avail on r/w long: 40     Queue depth: 1
>        Standby timer values: spec'd by Standard, no device specific minimum
>        R/W multiple sector transfer: Max = 16  Current = 16
>        DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
>             Cycle time: min=120ns recommended=120ns
>        PIO: pio0 pio1 pio2 pio3 pio4
>             Cycle time: no flow control=160ns  IORDY flow control=120ns
>Commands/features:
>        Enabled Supported:
>           *    READ BUFFER cmd
>           *    WRITE BUFFER cmd
>           *    Look-ahead
>           *    Write cache
>           *    Power Management feature set
>           *    SMART feature set
>
>root@bert:/usr/src/linux# hdparm -iI /dev/hdb
>
>/dev/hdb:
>
> Model=Maxtor 6E030L0, FwRev=NAR61590, SerialNo=E178CV5E
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
> CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=60058656
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes:  pio0 pio1 pio2 pio3 pio4
> DMA modes:  mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: (null):
>
> * signifies the current active mode
>
>
>ATA device, with non-removable media
>        Model Number:       Maxtor 6E030L0
>        Serial Number:      E178CV5E
>        Firmware Revision:  NAR61590
>Standards:
>        Supported: 7 6 5 4
>        Likely used: 7
>Configuration:
>        Logical         max     current
>        cylinders       16383   17475
>        heads           16      15
>        sectors/track   63      63
>        --
>        CHS current addressable sectors:   16513875
>        LBA    user addressable sectors:   60058656
>        device size with M = 1024*1024:       29325 MBytes
>        device size with M = 1000*1000:       30750 MBytes (30 GB)
>Capabilities:
>        LBA, IORDY(can be disabled)
>        Queue depth: 1
>        Standby timer values: spec'd by Standard, no device specific minimum
>        R/W multiple sector transfer: Max = 16  Current = 16
>        Advanced power management level: unknown setting (0x0000)
>        Recommended acoustic management value: 192, current value: 254
>        DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
>             Cycle time: min=120ns recommended=120ns
>        PIO: pio0 pio1 pio2 pio3 pio4
>             Cycle time: no flow control=120ns  IORDY flow control=120ns
>Commands/features:
>        Enabled Supported:
>           *    NOP cmd
>           *    READ BUFFER cmd
>           *    WRITE BUFFER cmd
>           *    Host Protected Area feature set
>           *    Look-ahead
>           *    Write cache
>           *    Power Management feature set
>                Security Mode feature set
>           *    SMART feature set
>           *    FLUSH CACHE EXT command
>           *    Mandatory FLUSH CACHE command
>           *    Device Configuration Overlay feature set
>           *    Automatic Acoustic Management feature set
>                SET MAX security extension
>                Advanced Power Management feature set
>           *    DOWNLOAD MICROCODE cmd
>           *    SMART self-test
>           *    SMART error logging
>Security:
>        Master password revision code = 65534
>                supported
>        not     enabled
>        not     locked
>        not     frozen
>        not     expired: security count
>        not     supported: enhanced erase
>HW reset results:
>        CBLID- above Vih
>        Device num = 1 determined by CSEL
>Checksum: correct
>
>hdb is accessed via dm and evms.   This is what the boot of reports:
>
>May 27 18:17:39 bert kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>May 27 18:17:39 bert kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>May 27 18:17:39 bert kernel: PIIX4: IDE controller at PCI slot 0000:00:14.1
>May 27 18:17:39 bert kernel: PIIX4: chipset revision 1
>May 27 18:17:39 bert kernel: PIIX4: not 100%% native mode: will probe irqs later
>May 27 18:17:39 bert kernel:     ide0: BM-DMA at 0x10c0-0x10c7, BIOS settings: hda:pio, hdb:DMA
>May 27 18:17:39 bert kernel:     ide1: BM-DMA at 0x10c8-0x10cf, BIOS settings: hdc:DMA, hdd:pio
>May 27 18:17:39 bert kernel: hda: WDC AC26400R, ATA DISK drive
>May 27 18:17:39 bert kernel: hdb: Maxtor 6E030L0, ATA DISK drive
>May 27 18:17:39 bert kernel: Using anticipatory io scheduler
>May 27 18:17:39 bert kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>May 27 18:17:39 bert kernel: hdc: HL-DT-ST RW/DVD GCC-4480B, ATAPI CD/DVD-ROM drive
>May 27 18:17:39 bert kernel: ide1 at 0x170-0x177,0x376 on irq 15
>May 27 18:17:39 bert kernel: pnp: the driver 'ide' has been registered
>May 27 18:17:39 bert kernel: hda: max request size: 128KiB
>May 27 18:17:39 bert kernel: hda: 12594960 sectors (6448 MB) w/512KiB Cache, CHS=13328/15/63, UDMA(33)
>May 27 18:17:39 bert kernel: hda: cache flushes supported
>May 27 18:17:39 bert kernel:  hda: hda1 hda2 hda3
>May 27 18:17:39 bert kernel: hdb: max request size: 128KiB
>May 27 18:17:39 bert kernel: hdb: 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(33)
>May 27 18:17:39 bert kernel: hdb: cache flushes supported
>May 27 18:17:39 bert kernel:  hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
> 
>followed later by:
>
>May 27 18:18:05 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:18:05 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:18:06 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:18:06 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:19:21 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:19:21 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:19:22 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:19:22 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:21:27 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:21:27 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>
>
>
>
>Hope this help,
>
>Ed
>
>On May 27, 2004 04:24 pm, Günther Persoons wrote:
>  
>
>>Hey,
>>When i mount my reiser partitie with the option barrier=flush i get
>>following message and error:
>>My harddrive is a 2.5 inch Fujitsu 20GB IDE.
>>
>>mount /dev/hda10 /tmp -o barrier=flush
>>mount: wrong fs type, bad option, bad superblock on /dev/hda10,
>>       or too many mounted file systems
>>Log:
>>ReiserFS: hda10: found reiserfs format "3.6" with standard journal
>>ReiserFS: hda10: using ordered data mode
>>reiserfs: using flush barriers
>>ReiserFS: hda10: journal params: device hda10, size 8192, journal first
>>block 18, max trans len 1024, max batch 900, max commit age 30, max
>>trans age 30
>>ReiserFS: hda10: checking transaction log (hda10)
>>hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>>hda: drive_cmd: error=0x04 { DriveStatusError }
>>hda: barrier support doesn't work
>>ReiserFS: hda10: warning: journal-837: IO error during journal replay
>>ReiserFS: hda10: warning: Replay Failure, unable to mount
>>ReiserFS: hda10: warning: sh-2022: reiserfs_fill_super: unable to
>>initialize journal space
>>    
>>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at  http://www.tux.org/lkml/
>
>
>  
>