Linux version 2.6.7-rc2 (andy@luto.stanford.edu) (gcc version 3.3.3 20040412 (Re d Hat Linux 3.3.3-7)) #1 Fri Jun 4 19:00:50 PDT 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ce000 - 00000000000d8000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data) BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126960 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000fa3f0 ACPI: RSDT (v001 AMIINT VIA_K8 0x00000010 MSFT 0x00000097) @ 0x1fff0000 ACPI: FADT (v001 AMIINT VIA_K8 0x00000011 MSFT 0x00000097) @ 0x1fff0030 ACPI: MADT (v001 AMIINT VIA_K8 0x00000009 MSFT 0x00000097) @ 0x1fff00c0 ACPI: DSDT (v001 VIA VIA_K8 0x00001000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 Built 1 zonelists Kernel command line: ro root=/dev/hda1 console=ttyS0,115200 console=tty0 commonc ap.newcaps=1 Unknown boot option `commoncap.newcaps=1': ignoring Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2000.031 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Memory: 515924k/524224k available (2037k kernel code, 7552k reserved, 862k data, 136k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3964.92 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 08 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 141k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f7510 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x645b, dseg 0xf0000 PnPBIOS: 11 nodes reported by PnP BIOS; 11 recorded by driver usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 3 PCI: Using ACPI for IRQ routing vesafb: probe of vesafb0 failed with error -6 Machine check exception polling timer started. Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected AGP bridge 0 agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 256M @ 0xd0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.0 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: ST3160023A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: ST3200822A, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hdc: max request size: 1024KiB hdc: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 > ide-floppy driver 0.99.newide ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: irq 5, pci mem e085ad00 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.2 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 11, io base 0000d400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 11, io base 0000d800 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.2: irq 10, io base 0000dc00 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 10, io base 0000e000 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 S4 S5) RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: raid1 personality registered as nr 3 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 136k freed EXT3 FS on hda1, internal journal device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com Adding 1004052k swap on /dev/hda2. Priority:1 extents:1 Adding 996020k swap on /dev/hdc2. Priority:1 extents:1 md: raidstart(pid 643) used deprecated START_ARRAY ioctl. This will not be suppo rted beyond 2.6 md: autorun ... md: considering hdc5 ... md: adding hdc5 ... md: adding hda5 ... md: created md0 md: bind md: bind md: running: raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. ReiserFS: md0: found reiserfs format "3.6" with standard journal ReiserFS: md0: using ordered data mode ReiserFS: md0: journal params: device md0, size 8192, journal first block 18, ma x trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: md0: checking transaction log (md0) ReiserFS: md0: Using r5 hash to sort names ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names ReiserFS: hda7: warning: read_super_block: found reiserfs format "3.6" with non- standard journal ReiserFS: hda7: using ordered data mode ReiserFS: hda7: journal params: device hda7, size 16384, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda7: checking transaction log (hda7) ReiserFS: hda7: Using r5 hash to sort names SGI XFS with ACLs, large block numbers, no debug enabled SGI XFS Quota Management subsystem XFS mounting filesystem hdc6 Ending clean XFS mount for filesystem: hdc6 ReiserFS: hdc1: found reiserfs format "3.6" with standard journal ReiserFS: hdc1: using ordered data mode ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc1: checking transaction log (hdc1) ReiserFS: hdc1: Using r5 hash to sort names ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1203 $ Ben Collins ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[3] MMIO=[cfffc000-cfffc7ff] Max Packet=[2048] ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00002c7728] Bridge firewalling registered Bridge does not support ioctl 0x8b01 Bridge does not support ioctl 0x8946 natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002 originally by Donald Becker http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder eth0: NatSemi DP8381[56] at 0xe0c3e000, 00:40:f4:58:9c:a9, IRQ 5. r8169 Gigabit Ethernet driver 1.2 loaded eth1: Identified chip type is 'RTL8169s/8110s'. eth1: RTL8169 at 0xe0c83f00, 00:0c:76:4e:df:cc, IRQ 11 eth1: Auto-negotiation Enabled. eth1: 1000Mbps Full-duplex operation. eth0: link up. eth0: Setting full-duplex based on negotiated link capability. eth0: Promiscuous mode enabled. device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propgating br0: port 1(eth0) entering forwarding state Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky via82xx: Assuming DXS channels with 48k fixed sample rate. Please try dxs_support=1 or dxs_support=4 option and report if it works on your machine. PCI: Setting latency timer of device 0000:00:11.5 to 64 Linux video capture interface: v1.00 bttv: driver version 0.9.14 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 10, latency: 32, mmio: 0xcddfe000 bttv0: using: Hauppauge (bt848) [card=2,insmod option] bttv0: gpio: en=00000000, out=00000000 in=003fffff [init] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] bttv: readee error bttv0: Hauppauge eeprom: invalid bttv0: Hauppauge eeprom: model=0, tuner= (4), radio=no bttv0: using tuner=17 bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found tvaudio: TV audio decoder + audio/video mux driver tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea642 0,tda8425,pic16c54 (PV951),ta8874z tuner: chip found at addr 0xc0 i2c-bus bt878 #0 [sw] tuner: type set to 17 (Philips NTSC_M (MK2)) by bt878 #0 [sw] bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0