From: Johannes Bauer <dfnsonfsduifb@gmx.de>
To: linux-kernel@vger.kernel.org
Subject: Re: 2.6.7 shows blank screen during boot with Radeon 9600 Mobility
Date: Sat, 26 Jun 2004 18:32:20 +0200 [thread overview]
Message-ID: <40DDA514.4080204@gmx.de> (raw)
In-Reply-To: <2842i-3m8-23@gated-at.bofh.it>
Hi,
I found another laptop showing the _exact_ symptoms, as soon as
Device Drivers --->
Graphics support --->
[*] Support for frame buffer devices
<*> ATI Radeon display support
is being enabled. This _definitely_ is a kernel bug, as it works with
2.6.6 just fine. Here's the other laptop's lspci:
ruedilap [~]: lspci
0000:00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host
& Memory & AGP Controller (rev 01)
0000:00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual
PCI-to-PCI bridge (AGP)
0000:00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL
Media IO] (rev 14)
0000:00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016
0000:00:02.3 FireWire (IEEE 1394): Silicon Integrated Systems [SiS]
FireWire Controller
0000:00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
0000:00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
0000:00:02.7 Multimedia audio controller: Silicon Integrated Systems
[SiS] Sound Controller (rev a0)
0000:00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f)
0000:00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
Controller
0000:00:04.0 Ethernet controller: Silicon Integrated Systems [SiS]
SiS900 PCI Fast Ethernet (rev 91)
0000:00:08.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350
[Mobility Radeon 9600 M10]
ruedilap [~]: lspci -v -v
0000:00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host
& Memory & AGP Controller (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at dc000000 (32-bit, non-prefetchable)
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=<none>
0000:00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual
PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d7e00000-d7efffff
Prefetchable memory behind bridge: c7c00000-d7cfffff
Expansion ROM at 0000a000 [disabled] [size=4K]
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL
Media IO] (rev 14)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:02.1 SMBus: Silicon Integrated Systems [SiS]: Unknown device 0016
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0c00 [size=32]
0000:00:02.3 FireWire (IEEE 1394): Silicon Integrated Systems [SiS]
FireWire Controller (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp: Unknown device 7007
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 3000ns max)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at dbfff000 (32-bit, non-prefetchable)
[size=dbfc0000]
Expansion ROM at 00020000 [disabled]
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
(prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE
Controller (A,B step)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 4: I/O ports at ff00 [size=16]
0000:00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0) (prog-if 00 [Generic])
Subsystem: Uniwill Computer Corp: Unknown device 4003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at d400
Region 1: I/O ports at d000 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.7 Multimedia audio controller: Silicon Integrated Systems
[SiS] Sound Controller (rev a0)
Subsystem: Uniwill Computer Corp: Unknown device 5203
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at dc00
Region 1: I/O ports at d800 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp: Unknown device 7001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dbffb000 (32-bit, non-prefetchable)
0000:00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp: Unknown device 7001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: Memory at dbffc000 (32-bit, non-prefetchable)
0000:00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp: Unknown device 7001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin C routed to IRQ 5
Region 0: Memory at dbffd000 (32-bit, non-prefetchable)
0000:00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
Controller (prog-if 20 [EHCI])
Subsystem: Uniwill Computer Corp: Unknown device 7002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 11
Region 0: Memory at dbffe000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: Silicon Integrated Systems [SiS]
SiS900 PCI Fast Ethernet (rev 91)
Subsystem: Uniwill Computer Corp: Unknown device 5002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at cc00 [size=dbfa0000]
Region 1: Memory at dbffa000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 00020000 [disabled]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Subsystem: Uniwill Computer Corp: Unknown device 3000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20000000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt-
PostWrite+
16-bit legacy interface ports at 0001
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350
[Mobility Radeon 9600 M10] (prog-if 00 [VGA])
Subsystem: Uniwill Computer Corp: Unknown device 2314
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c8000000 (32-bit, prefetchable)
Region 1: I/O ports at a800 [size=256]
Region 2: Memory at d7ef0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit-
FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
ruedilap [~]:
Greetings,
Joe
next parent reply other threads:[~2004-06-26 16:32 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <2842i-3m8-23@gated-at.bofh.it>
2004-06-26 16:32 ` Johannes Bauer [this message]
2004-06-17 12:12 2.6.7 shows blank screen during boot with Radeon 9600 Mobility Johannes Bauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=40DDA514.4080204@gmx.de \
--to=dfnsonfsduifb@gmx.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox