From: Jack Sprat <trashcan@chilitech.com>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM: linux-2.4.x sound module opl3sa2
Date: Thu, 22 Jul 2004 15:13:59 -0400 [thread overview]
Message-ID: <410011F7.7030202@chilitech.com> (raw)
I submitted this possible bug months ago to maintainer. No response for
whatever reason and the potential bug persists [or I am in error ;-) ].
-- Ron H.
1. Sound driver opl3sa2.c: Possible incorrect display of port number
2. Output from /var/log/messages; Jun 14(unpatched), Jun 18 (patched)
The suspect output is in line 2 "Search for a card at"
Jun 14 11:15:45 micron kernel: opl3sa2: Found OPL3-SA3 (YMF715 or YMF719)
Jun 14 11:15:45 micron kernel: opl3sa2: Search for a card at 0x880.
Jun 14 11:15:45 micron kernel: opl3sa2: Control I/O port 0x370 is not a
YMF7xx chipset!
Jun 18 21:43:53 micron kernel: opl3sa2: Found OPL3-SA3 (YMF715 or YMF719)
Jun 18 21:43:53 micron kernel: opl3sa2: Search for a card at 0x370.
Jun 18 21:43:53 micron kernel: opl3sa2: Control I/O port 0x370 is not a
YMF7xx chipset!
Note that 0x370 = 3*256 + 7 * 16 = 880 ; port 0x370 incorrectly
displayed as 0x880
An attempt at a patch (patch program run from /usr/src/linux):
---------------------------------
diff -durN linux-2.4.x/drivers/sound/opl3sa2.c
linux-2.4.x.new/drivers/sound/opl3sa2.c
--- linux-2.4.x/drivers/sound/opl3sa2.c 2002-08-02 20:39:44.000000000 -0400
+++ linux-2.4.x.new/drivers/sound/opl3sa2.c 2004-06-18
20:57:54.000000000 -0400
@@ -1023,7 +1023,7 @@
if(io == -1)
break;
isapnp=0;
- printk(KERN_INFO PFX "Search for a card at
0x%d.\n", io);
+ printk(KERN_INFO PFX "Search for a card at
%#x.\n", io);
/* Fall through */
}
#endif
--------------------- End patch ----------------
I suspect the remainder of this report is unnecessary but is included...
3. modules sound opl3sa2.c linux-2.4.x
4. Linux version 2.4.22-1.2197.nptl (bhcompile@daffy.perf.redhat.com)
(gcc version 3.2.3 20030422 (Red Hat Linux 3.2.3-6
)) #1 Thu Jul 1 15:29:17 EDT 2004
5. N/A
6. From modules.conf:
options opl3sa2 io=0x370 mss_io=0x530 mpu_io=0x330 irq=7 dma=0 dma2=3
7. Nothing unusual in environment
7.1 If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux micron.readyto.rumble 2.4.22-1.2197.nptl #1 Thu Jul 1 15:29:17 EDT
2004 i686 i686 i386 GNU/Linux
Gnu C 3.3.2
Gnu make 3.79.1
util-linux 2.11y
mount 2.11y
modutils 2.4.25
e2fsprogs 1.34
jfsutils 1.1.3
reiserfsprogs 3.6.8
pcmcia-cs 3.1.31
quota-tools 3.06.
PPP 2.4.1
isdn4k-utils 3.3
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 2.0.17
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded lp parport autofs 8139too mii floppy sg scsi_mod
opl3sa2 mpu401 ad1848 sound soundcore keybdev mo
usedev hid input usb-uhci usbcore ext3 jbd
7.2
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 3
model name : Pentium II (Klamath)
stepping : 3
cpu MHz : 266.618
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov mmx
bogomips : 532.48
7.3
lp 8196 0 (autoclean)
parport 33952 0 (autoclean) [lp]
autofs 11156 0 (autoclean) (unused)
8139too 15560 1
mii 3736 0 [8139too]
floppy 55036 0 (autoclean)
sg 33804 0 (autoclean) (unused)
scsi_mod 107496 1 (autoclean) [sg]
opl3sa2 10000 1
mpu401 22372 0 [opl3sa2]
ad1848 25580 0 [opl3sa2]
sound 68468 1 [opl3sa2 mpu401 ad1848]
soundcore 6148 6 [sound]
keybdev 2432 0 (unused)
mousedev 5012 1
hid 22724 0 (unused)
input 5664 0 [keybdev mousedev hid]
usb-uhci 24460 0 (unused)
usbcore 73120 1 [hid usb-uhci]
ext3 65252 7
jbd 47468 7 [ext3]
7.4
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-0101 : opl3sa2
0170-0177 : ide1
01f0-01f7 : ide0
0213-0213 : isapnp read
02f8-02ff : serial(auto)
0300-0301 : mpu401
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0a79-0a79 : isapnp write
0cf8-0cff : PCI conf1
0e80-0e83 : WSS config
0e84-0e87 : MS Sound System
1000-100f : Intel Corp. 82371AB/EB/MB PIIX4 IDE
1000-1007 : ide0
1008-100f : ide1
1020-103f : Intel Corp. 82371AB/EB/MB PIIX4 USB
1020-103f : usb-uhci
1400-14ff : D-Link System Inc RTL8139 Ethernet
1400-14ff : 8139too
7000-701f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
8000-803f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-040fdbff : System RAM
00100000-00253f65 : Kernel code
00253f66-003665a7 : Kernel data
040fdc00-040ff7ff : ACPI Tables
040ff800-040ffbff : ACPI Non-volatile Storage
040ffc00-0fffffff : System RAM
f4000000-f40000ff : D-Link System Inc RTL8139 Ethernet
f4000000-f40000ff : 8139too
f5000000-f5ffffff : PCI Bus #01
f5000000-f5ffffff : NVidia / SGS Thomson (Joint Venture) Riva128
f8000000-fbffffff : Intel Corp. 440LX/EX - 82443LX/EX Host bridge
fc000000-fcffffff : PCI Bus #01
fc000000-fcffffff : NVidia / SGS Thomson (Joint Venture) Riva128
fffe7000-ffffffff : reserved
00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev
03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f5000000-f5ffffff
Prefetchable memory behind bridge: fc000000-fcffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1000 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1020 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0f.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
Subsystem: D-Link System Inc DFE-530TX+ 10/100 Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: NVidia / SGS Thomson (Joint Venture)
Riva128 (rev 10) (prog-if 00 [VGA])
Subsystem: Diamond Multimedia Systems Viper V330
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=4M]
Capabilities: [44] AGP version 1.0
Status: RQ=4 SBA- 64bit- FW- Rate=x1
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Attached devices: none
reply other threads:[~2004-07-22 19:10 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=410011F7.7030202@chilitech.com \
--to=trashcan@chilitech.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox