* hda: dma_timer_expiry: dma status == 0x24
@ 2003-06-25 8:20 Semler Michal
0 siblings, 0 replies; 7+ messages in thread
From: Semler Michal @ 2003-06-25 8:20 UTC (permalink / raw)
To: linux-kernel
Hello,
after running 2.4.21 I getts into dmesg one time per day
this message:
hda: dma_timer_expiry: dma status == 0x24
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
this never did before. I tried revert to 2.4.20
and it's clean?
hda: ST360021A, ATA DISK drive
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63,
UDMA(100)
Partition check:
hda: hda1 hda2 hda3
Thanks
CIJOML
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: hda: dma_timer_expiry: dma status == 0x24
[not found] <200306251109.44083.duncan.sands@math.u-psud.fr>
@ 2003-06-25 9:05 ` Semler Michal
2003-06-25 9:27 ` Duncan Sands
0 siblings, 1 reply; 7+ messages in thread
From: Semler Michal @ 2003-06-25 9:05 UTC (permalink / raw)
To: Duncan Sands; +Cc: linux-kernel
[-- Attachment #1: Type: TEXT/PLAIN, Size: 102 bytes --]
Yes.
DMESG included
CIJOML
On Wed, 25 Jun 2003, Duncan Sands wrote:
> UP with APIC?
>
> Duncan.
>
[-- Attachment #2: Type: TEXT/PLAIN, Size: 13913 bytes --]
Linux version 2.4.21 (root@ABicko.abclinuxu.cz) (gcc version 3.0.4) #2 So èen 21 14:12:51 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fe40000 (usable)
BIOS-e820: 000000001fe40000 - 000000001fe50000 (ACPI data)
BIOS-e820: 000000001fe50000 - 000000001ff00000 (ACPI NVS)
510MB LOWMEM available.
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000fd000 reserved twice.
hm, page 000fe000 reserved twice.
On node 0 totalpages: 130624
zone(0): 4096 pages.
zone(1): 126528 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f7170
RSD PTR v0 [ACPIAM]
__va_range(0x1fe40000, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [INTEL D845GBV 8195.550]
__va_range(0x1fe40200, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fe40200, 0x81): idx=8 mapped at ffff6000
ACPI table found: FACP v2 [INTEL D845GBV 8195.550]
__va_range(0x1fe40300, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fe40300, 0x68): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [INTEL D845GBV 8195.550]
__va_range(0x1fe40300, 0x68): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0001] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16
LAPIC_NMI (acpi_id[0x0001] polarity[0x0] trigger[0x0] lint[0x1])
LAPIC (acpi_id[0x0002] id[0x81] enabled[0])
CPU 1 (0x8100) disabled
LAPIC_NMI (acpi_id[0x0002] polarity[0x0] trigger[0x0] lint[0x1])
IOAPIC (id[0x1] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
2 CPUs total
Local APIC address fee00000
__va_range(0x1fe44350, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fe44350, 0x84): idx=8 mapped at ffff6000
ACPI table found: ASF! v16 [AMIASF I845GASF 0.1]
ACPI: Unsupported table ASF!
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: BrkdleG-ICH4 APIC at: 0xFEE00000
I/O APIC #1 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: auto BOOT_IMAGE=linux-raid ro root=900 hda=116301,16,63
ide_setup: hda=116301,16,63
Initializing CPU#0
Detected 1599.962 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3191.60 BogoMIPS
Memory: 514368k/522496k available (1238k kernel code, 7740k reserved, 475k data, 92k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.60GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-20, 1-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 24.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 1 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 C9
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 D1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1600.0098 MHz.
..... host bus clock speed is 100.0004 MHz.
cpu: 0, clocks: 1000004, slice: 500002
CPU0<T0:1000000,T1:499984,D:14,S:500002,C:1000004>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 21
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com>
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
ACPI-0202: *** Warning: Invalid table signature ASF! found
ACPI-0094: *** Error: Acpi_load_tables: Error getting required tables (DSDT/FADT/FACS): AE_BAD_SIGNATURE
ACPI-0115: *** Error: Acpi_load_tables: Could not load tables: AE_BAD_SIGNATURE
ACPI: System description table load failed
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:02:B3:A8:6D:22, IRQ 21.
Board assembly 751767-004, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x3258698e).
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: Detected an Intel 845G Chipset.
agpgart: detected 380K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST360021A, ATA DISK drive
blk: queue c02f53a0, I/O limit 4095Mb (mask 0xffffffff)
hdc: ST360015A, ATA DISK drive
blk: queue c02f57f4, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(100)
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3
hdc: hdc1 hdc2 hdc3
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller
ehci-hcd 00:1d.7: irq 23, pci mem e0895c00
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 6 ports detected
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 00000089]
[events: 00000080]
[events: 00000089]
[events: 00000080]
md: autorun ...
md: considering hdc3 ...
md: adding hdc3 ...
md: adding hda3 ...
md: created md1
md: bind<hda3,1>
md: bind<hdc3,2>
md: running: <hdc3><hda3>
md: hdc3's event counter: 00000080
md: hda3's event counter: 00000080
md: RAID level 1 does not need chunksize! Continuing anyway.
md1: max total readahead window set to 124k
md1: 1 data-disks, max readahead per data-disk: 124k
raid1: device hdc3 operational as mirror 1
raid1: device hda3 operational as mirror 0
raid1: raid set md1 active with 2 out of 2 mirrors
md: updating md1 RAID superblock on device
md: hdc3 [events: 00000081]<6>(write) hdc3's sb offset: 1975104
md: hda3 [events: 00000081]<6>(write) hda3's sb offset: 1975104
md: considering hdc1 ...
md: adding hdc1 ...
md: adding hda1 ...
md: created md0
md: bind<hda1,1>
md: bind<hdc1,2>
md: running: <hdc1><hda1>
md: hdc1's event counter: 00000089
md: hda1's event counter: 00000089
md: RAID level 1 does not need chunksize! Continuing anyway.
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device hdc1 operational as mirror 1
raid1: device hda1 operational as mirror 0
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
md: hdc1 [events: 0000008a]<6>(write) hdc1's sb offset: 52734400
md: hda1 [events: 0000008a]<6>(write) hda1's sb offset: 52734400
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 92k freed
Adding Swap: 1975096k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal
Real Time Clock Driver v1.10e
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4082 buckets, 32656 max) - 292 bytes per conntrack
keyboard: Timeout - AT keyboard not present?(f4)
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
sending pkt_too_big (len[1500] pmtu[1488]) to self
hda: dma_timer_expiry: dma status == 0x24
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
hda: dma_timer_expiry: dma status == 0x24
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
hda: dma_timer_expiry: dma status == 0x24
hda: lost interrupt
hda: dma_intr: bad DMA status (dma_stat=30)
hda: dma_intr: status=0x50 { DriveReady SeekComplete }
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: hda: dma_timer_expiry: dma status == 0x24
2003-06-25 9:05 ` Semler Michal
@ 2003-06-25 9:27 ` Duncan Sands
0 siblings, 0 replies; 7+ messages in thread
From: Duncan Sands @ 2003-06-25 9:27 UTC (permalink / raw)
To: Semler Michal; +Cc: linux-kernel
On Wednesday 25 June 2003 11:05, Semler Michal wrote:
> Yes.
>
> DMESG included
>
> CIJOML
>
> On Wed, 25 Jun 2003, Duncan Sands wrote:
> > UP with APIC?
> >
> > Duncan.
Try turning off the APIC or use the latest -ac kernel.
Duncan.
^ permalink raw reply [flat|nested] 7+ messages in thread
* hda: dma_timer_expiry: dma status == 0x24
@ 2004-08-07 19:20 David Ford
2004-08-07 21:47 ` Alan Cox
0 siblings, 1 reply; 7+ messages in thread
From: David Ford @ 2004-08-07 19:20 UTC (permalink / raw)
To: linux-kernel mailing list
[-- Attachment #1: Type: text/plain, Size: 3484 bytes --]
My desktop is experiencing issues with DMA lately. This has been going
on with the 2.6.8-rcX releases IIRC. I'm currently on rc3. The
hardware is all brand new.
Scott ~ # hdparm -i /dev/hda
/dev/hda:
Model=SAMSUNG SP1614N, FwRev=TM100-23, SerialNo=0642J1FW704776
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: (null):
Scott ~ # lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP]
Host Bridge (rev 01)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800 South]
0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80)
0000:00:08.0 RAID bus controller: Promise Technology, Inc. PDC20378
(FastTrak 378/SATA 378) (rev 02)
0000:00:09.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875J
(rev 04)
0000:00:0a.0 Ethernet controller: 3Com Corporation 3c940
10/100/1000Base-T [Marvell] (rev 12)
0000:00:0c.0 Communication controller: Conexant HCF 56k Data/Fax Modem
(rev 08)
0000:00:0d.0 Ethernet controller: Lite-On Communications Inc LNE100TX
(rev 20)
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA
RAID Controller (rev 80)
0000:00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81)
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 81)
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[K8T800 South]
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce
FX 5200] (rev a1)
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hdd: irq timeout: status=0x80 { Busy }
hdd: irq timeout: error=0x00
hdd: DMA disabled
hdd: ATAPI reset complete
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
[-- Attachment #2: dmesg.lastboot --]
[-- Type: text/plain, Size: 28426 bytes --]
Bootdata ok (command line is root=/dev/hda3 console=ttyS0,115200n8 console=tty0 serial=0,115200n8 ro noexec=on)
Linux version 2.6.8-rc3 (root@Scott) (gcc version 3.4.1 (Gentoo Linux 3.4.1, ssp-3.4-2, pie-8.7.6.3)) #1 Tue Aug 3 19:44:16 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 130864
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126768 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Looks like a VIA chipset. Disabling IOMMU. Overwrite with "iommu=allowed"
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa870
ACPI: XSDT (v001 A M I OEMXSDT 0x09000323 MSFT 0x00000097) @ 0x000000001ff30100
ACPI: FADT (v003 A M I OEMFACP 0x09000323 MSFT 0x00000097) @ 0x000000001ff30290
ACPI: MADT (v001 A M I OEMAPIC 0x09000323 MSFT 0x00000097) @ 0x000000001ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x09000323 MSFT 0x00000097) @ 0x000000001ff40040
ACPI: DSDT (v001 SK8V_ SK8V_013 0x00000013 MSFT 0x0100000d) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda3 console=ttyS0,115200n8 console=tty0 serial=0,115200n8 ro noexec=on
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2200.182 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 506728k/523456k available (4335k kernel code, 15988k reserved, 2255k data, 192k init)
Calibrating delay loop... 4308.99 BogoMIPS
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 148 stepping 08
Using local APIC NMI watchdog using perfctr0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
Detected 12.501 MHz APIC timer.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
IOAPIC[0]: Set PCI routing entry (1-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169
IOAPIC[0]: Set PCI routing entry (1-18 -> 0xb1 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 169
IOAPIC[0]: Set PCI routing entry (1-17 -> 0xb9 -> IRQ 17 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177
IOAPIC[0]: Set PCI routing entry (1-20 -> 0xc1 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193
IOAPIC[0]: Set PCI routing entry (1-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 201
IOAPIC[0]: Set PCI routing entry (1-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B9
12 001 01 1 1 0 1 0 1 1 B1
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 C1
15 001 01 1 1 0 1 0 1 1 C9
16 001 01 1 1 0 1 0 1 1 D1
17 0F2 02 1 0 0 0 0 0 2 13
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ169 -> 0:16
IRQ185 -> 0:17
IRQ177 -> 0:18
IRQ193 -> 0:20
IRQ201 -> 0:21
IRQ209 -> 0:22
.................................... done.
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
agpgart: Detected AGP bridge 0
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
udf: registering filesystem
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.0, from 5 to 9
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 9
PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9
PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1)
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.100 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
IOAPIC[0]: Set PCI routing entry (1-4 -> 0x49 -> IRQ 4 Mode:0 Active:0)
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
sk98lin: Network Device Driver v6.23
(C)Copyright 1999-2004 Marvell(R).
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
eth0: 3Com Gigabit LOM (3C940)
PrefPort:A RlmtMode:Check Link State
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177
Linux Tulip driver version 1.1.13 (May 11, 2002)
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177
tulip0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth1: Lite-On 82c168 PNIC rev 32 at 0xb000, 00:A0:CC:56:CB:FB, IRQ 177.
netconsole: not configured, aborting
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: SAMSUNG SP1614N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-700A, ATAPI CD/DVD-ROM drive
hdd: 4X4X32, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
PCI: Enabling device 0000:00:09.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:09.0 to 64
sym0: <875> rev 0x4 at pci 0000:00:09.0 irq 169
sym0: Symbios NVRAM, ID 15, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCAN FOR LUNS disabled for targets 1.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18j
Vendor: UMAX Model: Astra 2400S Rev: V1.1
Type: Scanner ANSI SCSI revision: 02
scsi(0:0:1:0): Beginning Domain Validation
scsi(0:0:1:0): Ending Domain Validation
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
libata version 1.02 loaded.
sata_promise version 1.00
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177
ata1: SATA max UDMA/133 cmd 0xFFFFFF0000067200 ctl 0xFFFFFF0000067238 bmdma 0x0 irq 177
ata2: SATA max UDMA/133 cmd 0xFFFFFF0000067280 ctl 0xFFFFFF00000672B8 bmdma 0x0 irq 177
ata1: no device found (phy stat 00000000)
scsi1 : sata_promise
ata2: no device found (phy stat 00000000)
scsi2 : sata_promise
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
sata_via(0000:00:0f.0): routed to hard irq line 11
ata3: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD400 irq 193
ata4: SATA max UDMA/133 cmd 0xE000 ctl 0xD802 bmdma 0xD408 irq 193
ata3: no device found (phy stat 00000000)
scsi3 : sata_via
ata4: no device found (phy stat 00000000)
scsi4 : sata_via
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 6
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169] MMIO=[fde00000-fde007ff] Max Packet=[2048]
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ieee1394: Loaded AMDTP driver
ieee1394: Loaded CMP driver
ehci_hcd: block sizes: qh 192 qtd 96 itd 192 sitd 96
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 201
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: capability 0001 at 68
ehci_hcd 0000:00:10.4: irq 201, pci mem ffffff00000a4000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
ehci_hcd 0000:00:10.4: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.8-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.4
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS2T++ Logitech TouchPad 3 on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
input: AT Translated Set 2 keyboard on isa0060/serio0
i2c /dev entries driver
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
hub 1-0:1.0: port 1 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.4: port 1 full speed --> companion
ehci_hcd 0000:00:10.4: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
ehci_hcd 0000:00:10.4: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
hub 1-0:1.0: port 6 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.4: port 6 full speed --> companion
ehci_hcd 0000:00:10.4: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800005eb58e]
Driver for 1-wire Dallas network protocol.
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:11.5 to 64
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
codec_read: codec 0 is not valid [0xfe0000]
ALSA device list:
#0: VIA 823x rev60 at 0xc800, irq 209
u32 classifier
Perfomance counters on
input device check on
Actions configured
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 28Kbytes
TCP: Hash tables configured (established 32768 bind 4681)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
NET: Registered protocol family 4
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SCTP: Hash tables configured (established 16384 bind 2340)
sctp_init_sock(sk: 000001001f9910a8)
powernow-k8: Power state transitions not supported
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
Adding 498004k swap on /dev/hda2. Priority:-1 extents:1
hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 201, io base 000000000000b400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.8-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
uhci_hcd 0000:00:10.1: irq 201, io base 000000000000b800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.8-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.4: port 1 full speed --> companion
ehci_hcd 0000:00:10.4: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
ehci_hcd 0000:00:10.4: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
uhci_hcd 0000:00:10.2: irq 201, io base 000000000000c000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: detected 2 ports
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
usb usb4: Manufacturer: Linux 2.6.8-rc3 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: irq 201, io base 000000000000c400
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: detected 2 ports
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: default language 0x0409
usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
usb usb5: Manufacturer: Linux 2.6.8-rc3 uhci_hcd
usb usb5: SerialNumber: 0000:00:10.3
usb usb5: hotplug
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: hotplug
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
hub 1-0:1.0: port 6 not reset yet, waiting 50ms
ehci_hcd 0000:00:10.4: port 6 full speed --> companion
ehci_hcd 0000:00:10.4: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT
uhci_hcd 0000:00:10.0: port 1 portsc 009b
hub 2-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 2-1: new full speed USB device using address 2
usb 2-1: skipped 1 descriptor after interface
usb 2-1: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
hub 2-1:1.0: usb_probe_interface
hub 2-1:1.0: usb_probe_interface - got id
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
hub 2-1:1.0: standalone hub
hub 2-1:1.0: individual port power switching
hub 2-1:1.0: individual port over-current protection
hub 2-1:1.0: power on to power good time: 100ms
hub 2-1:1.0: local power source is good
hub 2-1:1.0: enabling power on all ports
uhci_hcd 0000:00:10.0: port 2 portsc 018a
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.1: port 1 portsc 018a
hub 3-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.1: port 2 portsc 008a
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 1 portsc 018a
hub 4-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.2: port 2 portsc 009b
hub 4-0:1.0: port 2, status 0101, change 0003, 12 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 4-2: new full speed USB device using address 2
usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-2: default language 0x0409
usb 4-2: Product: EZ USB/Ethernet Converter
usb 4-2: Manufacturer: SMC, Inc
usb 4-2: SerialNumber: 0001
usb 4-2: hotplug
usb 4-2: adding 4-2:1.0 (config #1, interface 0)
usb 4-2:1.0: hotplug
uhci_hcd 0000:00:10.3: port 1 portsc 018a
hub 5-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
drivers/usb/net/pegasus.c: v0.5.12 (2003/06/06):Pegasus/Pegasus II USB Ethernet driver
pegasus 4-2:1.0: usb_probe_interface
pegasus 4-2:1.0: usb_probe_interface - got id
eth3: SMC 202 USB Ethernet
usbcore: registered new driver pegasus
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
uhci_hcd 0000:00:10.3: port 2 portsc 018a
hub 5-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:10.1: suspend_hc
hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-1:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-1.1: new low speed USB device using address 3
usb 2-1.1: skipped 1 descriptor after interface
usb 2-1.1: new device strings: Mfr=3, Product=1, SerialNumber=2
usb 2-1.1: default language 0x0409
usb 2-1.1: Product: Back-UPS ES 350 FW:1.e2.D USB FW:e2
usb 2-1.1: Manufacturer: APC
usb 2-1.1: SerialNumber: AB0303246275
usb 2-1.1: hotplug
usb 2-1.1: adding 2-1.1:1.0 (config #1, interface 0)
usb 2-1.1:1.0: hotplug
usbhid 2-1.1:1.0: usb_probe_interface
usbhid 2-1.1:1.0: usb_probe_interface - got id
uhci_hcd 0000:00:10.3: suspend_hc
drivers/usb/core/file.c: looking for a minor, starting at 0
hiddev0: USB HID v1.10 Device [APC Back-UPS ES 350 FW:1.e2.D USB FW:e2] on usb-0000:00:10.0-1.1
hub 2-1:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 2-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
hub 2-1:1.0: port 2 not reset yet, waiting 10ms
usb 2-1.2: new low speed USB device using address 4
usb 2-1.2: skipped 1 descriptor after interface
usb 2-1.2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1.2: default language 0x0409
usb 2-1.2: Product: USB Receiver
usb 2-1.2: Manufacturer: Logitech
usb 2-1.2: hotplug
usb 2-1.2: adding 2-1.2:1.0 (config #1, interface 0)
usb 2-1.2:1.0: hotplug
usbhid 2-1.2:1.0: usb_probe_interface
usbhid 2-1.2:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1.2
hub 2-1:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-1:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
hub 2-1:1.0: port 3 not reset yet, waiting 10ms
usb 2-1.3: new full speed USB device using address 5
usb 2-1.3: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-1.3: hotplug
usb 2-1.3: adding 2-1.3:1.0 (config #1, interface 0)
usb 2-1.3:1.0: hotplug
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
ov511 2-1.3:1.0: usb_probe_interface
ov511 2-1.3:1.0: usb_probe_interface - got id
drivers/usb/media/ov511.c: USB OV511 video device found
drivers/usb/media/ov511.c: model: AverMedia InterCam Elite
drivers/usb/media/ov511.c: Sensor is an OV7610
drivers/usb/media/ov511.c: Device at usb-0000:00:10.0-1.3 registered to minor 0
hub 2-1:1.0: port 4, status 0101, change 0001, 12 Mb/s
hub 2-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101
hub 2-1:1.0: port 4 not reset yet, waiting 10ms
usb 2-1.4: new full speed USB device using address 6
usb 2-1.4: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1.4: default language 0x0409
usb 2-1.4: Product: Camera
usb 2-1.4: hotplug
usb 2-1.4: adding 2-1.4:1.0 (config #1, interface 0)
usb 2-1.4:1.0: hotplug
Disabled Privacy Extensions on device ffffffff806da5c0(lo)
cable: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: none
irq moderation: disabled
scatter-gather: enabled
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2044 buckets, 16352 max) - 480 bytes per conntrack
intranet: Setting full-duplex based on MII#1 link partner capability of 45e1.
[-- Attachment #3: david+challenge-response.vcf --]
[-- Type: text/x-vcard, Size: 183 bytes --]
begin:vcard
fn:David Ford
n:Ford;David
email;internet:david@blue-labs.org
title:Industrial Geek
tel;home:Ask please
tel;cell:(203) 650-3611
x-mozilla-html:TRUE
version:2.1
end:vcard
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: hda: dma_timer_expiry: dma status == 0x24
2004-08-07 19:20 hda: dma_timer_expiry: dma status == 0x24 David Ford
@ 2004-08-07 21:47 ` Alan Cox
2004-08-07 23:26 ` David Ford
2004-08-09 20:10 ` David Ford
0 siblings, 2 replies; 7+ messages in thread
From: Alan Cox @ 2004-08-07 21:47 UTC (permalink / raw)
To: David Ford; +Cc: Linux Kernel Mailing List
On Sad, 2004-08-07 at 20:20, David Ford wrote:
> My desktop is experiencing issues with DMA lately. This has been going
> on with the 2.6.8-rcX releases IIRC. I'm currently on rc3. The
> hardware is all brand new.
1. Does it recover after the timeout/lost irq
2. Does it occur with acpi=off
3. Have you tested say 2.4 or "otherOS" on it ?
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: hda: dma_timer_expiry: dma status == 0x24
2004-08-07 21:47 ` Alan Cox
@ 2004-08-07 23:26 ` David Ford
2004-08-09 20:10 ` David Ford
1 sibling, 0 replies; 7+ messages in thread
From: David Ford @ 2004-08-07 23:26 UTC (permalink / raw)
To: Alan Cox; +Cc: Linux Kernel Mailing List
[-- Attachment #1: Type: text/plain, Size: 864 bytes --]
1. yes it recovers after about 20 seconds of machine stall, then does it
again in a minute or two (using cdroms), or many minutes elsewise.
2. haven't had a chance to try with acpi=off, turning off acpi broke
things for me a while back
3. haven't tested 2.4 (it didn't do this several kernels back), don't
have any other operating systems
It's also worth noting that this timeout is severely aggravated by using
my DVD and CD drives on hdc and hdd respectively.
David
Alan Cox wrote:
>On Sad, 2004-08-07 at 20:20, David Ford wrote:
>
>
>>My desktop is experiencing issues with DMA lately. This has been going
>>on with the 2.6.8-rcX releases IIRC. I'm currently on rc3. The
>>hardware is all brand new.
>>
>>
>
>1. Does it recover after the timeout/lost irq
>2. Does it occur with acpi=off
>3. Have you tested say 2.4 or "otherOS" on it ?
>
>
[-- Attachment #2: david+challenge-response.vcf --]
[-- Type: text/x-vcard, Size: 183 bytes --]
begin:vcard
fn:David Ford
n:Ford;David
email;internet:david@blue-labs.org
title:Industrial Geek
tel;home:Ask please
tel;cell:(203) 650-3611
x-mozilla-html:TRUE
version:2.1
end:vcard
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: hda: dma_timer_expiry: dma status == 0x24
2004-08-07 21:47 ` Alan Cox
2004-08-07 23:26 ` David Ford
@ 2004-08-09 20:10 ` David Ford
1 sibling, 0 replies; 7+ messages in thread
From: David Ford @ 2004-08-09 20:10 UTC (permalink / raw)
To: Alan Cox; +Cc: Linux Kernel Mailing List
[-- Attachment #1: Type: text/plain, Size: 1148 bytes --]
Yes, it still occurs with acpi=off, albeit with far less frequency.
I've had my machine up for 1.5 hours now, ripping two CDs at a time,
playing an AVI movie in loop, playing a bunch of MP3s, cat /allfiles
>/dev/null, ls -laR, running KDE with numerous KDE apps also running;
all simultaneously. The load is about 8, I'm 130M into swap (512M machine)
1> This would have been impossible without acpi=off.
2> Only one timeout has occured, by now several hundred would have
normally happened
David
Alan Cox wrote:
>On Sad, 2004-08-07 at 20:20, David Ford wrote:
>
>
>>My desktop is experiencing issues with DMA lately. This has been going
>>on with the 2.6.8-rcX releases IIRC. I'm currently on rc3. The
>>hardware is all brand new.
>>
>>
>
>1. Does it recover after the timeout/lost irq
>2. Does it occur with acpi=off
>3. Have you tested say 2.4 or "otherOS" on it ?
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
>
>
[-- Attachment #2: david+challenge-response.vcf --]
[-- Type: text/x-vcard, Size: 183 bytes --]
begin:vcard
fn:David Ford
n:Ford;David
email;internet:david@blue-labs.org
title:Industrial Geek
tel;home:Ask please
tel;cell:(203) 650-3611
x-mozilla-html:TRUE
version:2.1
end:vcard
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2004-08-09 20:12 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-08-07 19:20 hda: dma_timer_expiry: dma status == 0x24 David Ford
2004-08-07 21:47 ` Alan Cox
2004-08-07 23:26 ` David Ford
2004-08-09 20:10 ` David Ford
[not found] <200306251109.44083.duncan.sands@math.u-psud.fr>
2003-06-25 9:05 ` Semler Michal
2003-06-25 9:27 ` Duncan Sands
-- strict thread matches above, loose matches on Subject: below --
2003-06-25 8:20 Semler Michal
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox