* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
@ 2004-11-11 16:46 Mark_H_Johnson
2004-11-11 17:31 ` K.R. Foley
0 siblings, 1 reply; 16+ messages in thread
From: Mark_H_Johnson @ 2004-11-11 16:46 UTC (permalink / raw)
To: Ingo Molnar
Cc: linux-kernel, Lee Revell, Rui Nuno Capela, K.R. Foley, Bill Huey,
Adam Heath, Florian Schmidt, Thomas Gleixner, Michal Schmidt,
Fernando Pablo Lopez-Lezcano, Karsten Wiese, Gunther Persoons,
emann, Shane Shrybman, Amit Shah
>i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>downloaded from the usual place:
>
> http://redhat.com/~mingo/realtime-preempt/
>
>this release includes fixes, new features and latency improvements.
It may be coincidence, but when I did
chrt -p -f 99 2
(to set IRQ 0 to max RT priority, like the other IRQ's)
I got the following deadlock.
==========================================
[ BUG: lock recursion deadlock detected! |
------------------------------------------
already locked: [c140c2e0] {&base->lock}
.. held by: ksoftirqd/0: 4 [c17953f0, 105]
... acquired at: run_timer_softirq+0x108/0x470
------------------------------
| showing all locks held by: | (ksoftirqd/0/4 [c17953f0, 105]):
------------------------------
#001: [c140c2e0] {&base->lock}
... acquired at: run_timer_softirq+0x108/0x470
#002: [c0576b6c] {&timer->lock}
... acquired at: __mod_timer+0x47/0x1d0
There are a LOT of messages that stream out after this problem.
I will be sending the full serial console log separately.
Will reboot shortly and see if this is a repeatable problem or not.
--Mark
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:46 [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Mark_H_Johnson
@ 2004-11-11 17:31 ` K.R. Foley
0 siblings, 0 replies; 16+ messages in thread
From: K.R. Foley @ 2004-11-11 17:31 UTC (permalink / raw)
To: Mark_H_Johnson
Cc: Ingo Molnar, linux-kernel, Lee Revell, Rui Nuno Capela, Bill Huey,
Adam Heath, Florian Schmidt, Thomas Gleixner, Michal Schmidt,
Fernando Pablo Lopez-Lezcano, Karsten Wiese, Gunther Persoons,
emann, Shane Shrybman, Amit Shah
Mark_H_Johnson@Raytheon.com wrote:
>>i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>>downloaded from the usual place:
>>
>> http://redhat.com/~mingo/realtime-preempt/
>>
>>this release includes fixes, new features and latency improvements.
>
>
> It may be coincidence, but when I did
> chrt -p -f 99 2
> (to set IRQ 0 to max RT priority, like the other IRQ's)
>
> I got the following deadlock.
>
I tried reproducing this but could not. Of course that doesn't mean
much. :) Also, is this really they way you typed it in? If so, it is
very possible that the pid it tried to chrt was 99 not 2.
kr
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.9-rc4-mm1-U9.3
@ 2004-10-22 13:35 Ingo Molnar
2004-10-22 15:50 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-10-22 13:35 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano
i have released the -U9.3 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this too is a fixes-only release.
Changes since -U9.2:
- tons more driver/mutex/completion conversion done by Thomas Gleixner
for: ppp, ipmi, parport/ieeee1284, scsi, hotplug, and more.
- iptables/netfilter deadlock fix, this should fix the bug reported by
Michal Schmidt.
- .config housekeeping: disallow the turning off of PREEMPT_BKL when
PREEMPT_REALTIME is on. This solves the build error reported by
Matthew L Foster.
- print the full stacktrace of the current task in the deadlock
detector and dont use show_stack(). This explains some of the weird
partial stackdumps reported.
- some more minor updates to the case when the deadlock detector turns
itself off due to reaching the limit. We kept the spinlock locked.
to create a -U9.3 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.8.tar.bz2
+ http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.9-rc4.bz2
+ http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.9-rc4/2.6.9-rc4-mm1/2.6.9-rc4-mm1.bz2
+ http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.9-rc4-mm1-U9.3
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10
2004-10-22 13:35 [patch] Real-Time Preemption, -RT-2.6.9-rc4-mm1-U9.3 Ingo Molnar
@ 2004-10-22 15:50 ` Ingo Molnar
2004-10-22 17:56 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10.2 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-10-22 15:50 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano
i have released the -U10 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this is purely a rebasing of -U9.3 to 2.6.9-mm1.
to create a -U10 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
+ http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.9/2.6.9-mm1/2.6.9-mm1.bz2
+ http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.9-mm1-U10
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10.2
2004-10-22 15:50 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10 Ingo Molnar
@ 2004-10-22 17:56 ` Ingo Molnar
2004-10-25 10:40 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-10-22 17:56 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Alexander Batyrshin
i have released the -U10.2 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this is a fixes-only release.
Changes since -U10:
- fixed a big bug present ever since: the BKL got dropped when a
spinlock-mutex was acquired and it scheduled away. This reduced the
locking efficiency of the BKL. A number of outstanding problems could
be affected, in particular this should fix the tty locking breakage
reported by Alexander Batyrshin and Adam Heath. UP and SMP systems
are affected too, with SMP systems having a higher chance to trigger
this condition.
- tulip.c breakage fix from Thomas Gleixner
- tg3 and 3c59x fixes.
- made the hardirq threads SCHED_FIFO by default. They get priorities
between 25 and 50, depending on the irq #. (this is pretty random but
i found no better scheme.) Made the softirq thread SCHED_FIFO by
default as well, albeit this probably will have to change. These
changes should make it easier to debug a hung system.
to create a -U10.2 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
+ http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.9/2.6.9-mm1/2.6.9-mm1.bz2
+ http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.9-mm1-U10.2
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0
2004-10-22 17:56 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10.2 Ingo Molnar
@ 2004-10-25 10:40 ` Ingo Molnar
2004-10-27 0:15 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0.3 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-10-25 10:40 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Alexander Batyrshin
i have released the -V0 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
NOTE: this is a highly experimental release, a more experimental one
than -U10.3.
the big change in the '-V' series of the patchset is that i have
converted the last couple of non-preemptible kernel subsystems to
fully-preemptible mutex-based locking. These subsystems are:
- the SLAB allocator
- the buddy page allocator
- waitqueue handling
- soft-timer subsystem
- security/selinux
- workqueues
- the random driver
this is probably the last 'big leap forward' in terms of the scope of
the patch. (having reached the ultimate scope: it now encompasses
everything ;)
But as an inevitable result of this big leap it will likely break in a
couple of places. Unfortunately these subsystems were largely
interdependent so it's an all-or-nothing step with not much middle
ground between the locking done in -U10.3 and in -V0.
another result of these changes is that the number of critical sections
in -V0 is roughly 30% of that in -U10.3. Now we only have the scheduler
and very lowlevel IRQ-hardware locks as raw spinlocks. (plus the lone
holdout vga_lock - which i will probably make a mutex too in the near
future)
[ NOTE: there's one known bug in this release: selinux on one of my
testsystems broke, it hangs during bootup. With CONFIG_SECURITY disabled
it works fine. I'm working on the fix. So please keep CONFIG_SECURITY
disabled for the time being. ]
other changes in -V0:
- build fixes: more driver fixes from Thomas Gleixner
- crash fix: fixed a bug found by Thomas Gleixner: rwsem runtime
initialization was racy.
- deadlock fix: fixed lockup bug caused by __schedule clearing
PREEMPT_ACTIVE. The need_resched loop is now outside of __schedule().
This might solve lockups/slowdowns reported by some people.
- latency fix: made keventd SCHED_FIFO - this could fix the mouse
related delays reported by a number of people.
- latency fix: fixed SMP lock-break mechanism of mutexes.
- usability feature: hard-interrupts get decreasing SCHED_FIFO priority
starting at prio 49 and stopping at prio 25. This should give a good
default.
- debug feature: implemented SysRq-D to show the list of tasks with
locks blocked on, if RW_SEM_DEADLOCK_DETECTION is enabled.
to create a -V0 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
+ http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.9/2.6.9-mm1/2.6.9-mm1.bz2
+ http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.9-mm1-V0
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0.3
2004-10-25 10:40 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0 Ingo Molnar
@ 2004-10-27 0:15 ` Ingo Molnar
2004-11-03 10:58 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm2-V0.7.1 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-10-27 0:15 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese
i have released the -V0.3 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this is a fixes-only release, but still experimental.
this release should fix a number of bugs that were reported for the V0
series: the futex.c assert, the lockups and the 'slowdown problem'.
The slowdown problem was an architectural issue that surfaced sometime
around U10 and increased in prominence as the the number of mutexes
increased and the number of spinlocks decreased. The futex.c assert was
related to this architectural issue as well, and most of the lockups
reported were i believe livelocks caused by the same issue. Also, the
scheduler path had an easy-to-trigger deadlock that often just silently
locked up.
some of the networking lockups might be related to this issue too, but i
think PREEMPT_REALTIME still has separate lock odering issues within the
networking code. Please re-report any deadlock-tracer asserts that you
might encounter.
Changes since -V0.2:
- HEAP_SIZE fix from Karsten Wiese
- fix hdparm-triggered debugging message reported by Mark H Johnson
- fixed mutex related preemption to not impact the task state, just
like a normal spinlock does. This necessiated the introduction of
TASK_RUNNING_MUTEX handling and related kernel infrastructure. This
framework avoids spurious wakeups done by mutex handling by isolating
the state changes done by normal wakeups vs. the state changes caused
by the mutex code.
- added per-CPU deschedule threads. This fixes a deadlock scenario and
it is also much faster than keventd.
- fix debugging message upon console unblanking
to create a -V0.3 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
+ http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.9/2.6.9-mm1/2.6.9-mm1.bz2
+ http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.9-mm1-V0.3
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm2-V0.7.1
2004-10-27 0:15 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0.3 Ingo Molnar
@ 2004-11-03 10:58 ` Ingo Molnar
2004-11-06 15:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.18 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-03 10:58 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
K.R. Foley
i have released the -V0.7.1 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this release is mainly a merge of -V0.6.9 to 2.6.10-rc2-mm2.
I havent done a proper changelog for a couple of days so here is a list
of bigger changes since -V0.4:
- implemented a first version of the priority inheritance handling and
priority inversion avoidance logic. This feature, after some initial
stability problems, solved the jackd and rtc_wakeup latencies that
were introduced by the ultra-finegrained locking in the -V series.
(the -T/U series had a coarser locking scheme triggered much lower
levels of priority inversion scenarios. The locking in the -V series
was clearly the tipping point.)
The new PI code covers all synchronization objects in Linux (on
PREEMPT_REALTIME): spinlocks, rwlocks, semaphores and rwsems.
Feedback on the design of this code would be welcome, and patches as
well, if you have a better scheme. The code is pretty modular so feel
free to experiment with alternative schemes.
- completely reworked the debugging framework. All lock types
(spinlocks, rwlocks, semaphores and rwsems) are now tracked, both
their symbolic name and their place of acquire are traced and printed
out upon detection of a deadlock. More and better information is
printed upon a deadlock. Got rid of the 'semaphore owners array' in
debugging mode, this reduces the footprint of semaphores quite
significantly and speeds up deadlock detection.
- got rid of the separate 'counted semaphores' implementation, it was
too intrusive. Made the core 'generic semaphores' implementation
compatible with vanilla Linux counted semaphore semantics. This also
enabled the unrolling of the completion-handling cleanups which,
while being very nice, were getting intrusive as well.
- countless build and driver related reports/fixes from lots of people
- more latency breaks in the remaining critical sections. A
particularly important one was the irqs-off latency bugfix from
Thomas Gleixner.
- sped up the i8259 PIC and the PIT timer hardirq handling routines -
these are now in the path of the longest latency.
- cleaned up IRQ and signal preemption - there were missed
check-rescheds and possibilities for IRQ recursion.
- made ALSA's ioctl()s not use the BKL - this fixes more jackd
latencies.
to create a -V0.7.1 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm2/2.6.10-rc1-mm2.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm2-V0.7.1
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.18
2004-11-03 10:58 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm2-V0.7.1 Ingo Molnar
@ 2004-11-06 15:57 ` Ingo Molnar
2004-11-08 9:16 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.19 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-06 15:57 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese
i have released the -V0.7.18 Real-Time Preemption patch, which can be
downloaded from:
http://redhat.com/~mingo/realtime-preempt/
this release includes fixes and cleanups.
Changes between -V0.7.12 and -V0.7.18:
- merged to 2.6.10-rc1-mm3
- fixed the e1000 xmit warnings reported by Amit Shah. Same fix for tg3
too.
- added irq-latency fix from Thomas Gleixner: re-enable interrupts
before adding timings to the entropy pool.
- fixed excessive ksoftirqd overhead during outgoing TCP traffic.
ksoftirqd kept getting re-woken while it had no way to progress.
- added upstream fix from Andi Kleen for the vmalloc bug causing module
load problems/crashes. Added ipc/shm fix too.
Changes between -V0.7.1 and -V0.7.12:
- big source level cleanups: completely rearranged the mutex type
definitions and source files, to make it reflect the code. Made
all locking objects based on a new, central lock type: struct
rt_mutex. This type is never exposed externally, it is internal to
the RT code. Unified all the RT locking code in kernel/rt.c, this
also simplified and sped things up. Undid collateral damage to the
generic rwsem code - it is now untouched and independent of the RT
code.
- rearranged the way spinlocks interact with the RT code and cleaned
up the RT spinlock definitions. Found and fixed a bug in the process:
rwlocks were dropping the BKL upon contention.
- small x86 speedup: call __schedule not preempt_schedule_irq from
work_resched.
- ported PREEMPT_RT to x64. This resulted in the generalization of some
of the x86 changes.
- hopefully fixed fbcon kernel logging
- hacked reiser4 to make it work on PREEMPT_REALTIME.
- dropped the swap-layout-improvements patch. While it was working fine
it's not necessary for latencies anymore under the PREEMPT_REALTIME
approach, and the swap-patch was getting intrusive.
- fixed preemption-bug in drain_cpu_caches() on SMP [bug introduced by
PREEMPT_REALTIME]
- new attempt at getting rid of the networking related deadlocks
- selinux deadlock fix and RCU-code conversion to RT semantics
to create a -V0.7.18 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.18
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.19
2004-11-06 15:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.18 Ingo Molnar
@ 2004-11-08 9:16 ` Ingo Molnar
2004-11-08 16:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.21 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-08 9:16 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
Gunther Persoons, emann, Shane Shrybman
i have released the -V0.7.19 Real-Time Preemption patch, which can be
downloaded from the usual place:
http://redhat.com/~mingo/realtime-preempt/
this release includes fixes only.
Changes since -V0.7.18:
- fixed a merge bug introduced in -V0.7.18, breaking bit-spinlocks used
by ext3's journalling code. This could/should fix the kjournald crash
reported by Adam Heath, Gunther Persoons and Eran Mann. Bug triggered
on !SMP kernels only.
- added upstream patch to fix a crash in bttv/btcx_riscmem_free(),
reported by Shane Shrybman.
- made modlist_lock raw again - this could fix the /proc/acpi related
asserts reported by Karsten Wiese.
- fixed -RT locking bug in zap_completion_queue(), this could fix the
asserts reported by Shane Shrybman and others.
to create a -V0.7.19 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.19
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.21
2004-11-08 9:16 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.19 Ingo Molnar
@ 2004-11-08 16:57 ` Ingo Molnar
2004-11-09 16:05 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.23 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-08 16:57 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
Gunther Persoons, emann, Shane Shrybman
i have released the -V0.7.21 Real-Time Preemption patch, which can be
downloaded from the usual place:
http://redhat.com/~mingo/realtime-preempt/
this release includes fixes and debugging-improvements.
Changes since -V0.7.20:
- reverted the modlist_lock change - it caused more problems than it
solved.
- implemented irqs-off critical section timing/tracing, inspired by the
positive results Thomas Gleixner got with a different kind of cli/sti
tracer. To activate it, enable CONFIG_CRITICAL_TIMING and
CONFIG_CRITICAL_IRQSOFF_TIMING and cli/sti latencies will be reported
'integrated' into the preempt on/off latencies.
- sped up tracing in a number of ways. Performance of the tracer slowly
eroded in the past week or two, it needed alignment and size fixes ,
inlining/branch-prediction updates and i got rid of unnecessary code.
The max latency is now traced in cycles - this got rid of an
expensive 64-bit division in the fastpath. (the /proc/sys tunables
are still in usecs so userspace should not notice anything.) It's
still not cheap but roughly 5 times faster than -V0.7.20's tracer, on
a fast desktop box.
- renamed CONFIG_PREEMPT_REALTIME to CONFIG_PREEMPT_RT - it's shorter.
- renamed CONFIG_PREEMPT_TIMING to CONFIG_CRITICAL_TIMING and
introduced CONFIG_CRITICAL_IRQSOFF_TIMING to enable cli/sti timing.
to create a -V0.7.21 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.21
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.23
2004-11-08 16:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.21 Ingo Molnar
@ 2004-11-09 16:05 ` Ingo Molnar
2004-11-11 14:44 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Ingo Molnar
0 siblings, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-09 16:05 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
Gunther Persoons, emann, Shane Shrybman, Amit Shah
i have released the -V0.7.23 Real-Time Preemption patch, which can be
downloaded from the usual place:
http://redhat.com/~mingo/realtime-preempt/
this release includes fixes, development/debugging improvements and
latency improvements and other speedups.
the biggest change is the reworked timing/tracing framework. Wakeup
timing became a compile-time thing and can be selected independently of
the preemption mode - i.e. it can now be used on near-vanilla !PREEMPT
kernels too, providing good wakeup-latency comparison of the various
preemption models.
irqs-off and preempt-off critical section timing/tracing can be selected
if wakeup timing is disabled, the two options can be selected separately
or together as well.
another improvement is that wakeup-timing now works correctly on SMP too
- the tracer 'follows' the highest-priority task in the system as it
gets bounced between CPUs and always traces the CPU where the task is
pending.
other changes since -V0.7.22:
- semaphore livelock fix: feedback from Mark H. Johnson pinpointed a
bug in the down_trylock() semaphore code: if preempted in the wrong
moment a lower-prio task could cause a higher-prio task to livelock
indefinitely. This fix could solve the 'keventd looping' problem
reported by Mark.
the fix is to make the down_trylock() code a bit simpler, but this
also introduces the potential for down_trylock() to get 'spurious'
locking-rejects. Hopefully this wont be a big problem - we dont
really guarantee that down_trylock() succeeds - but code using higher
semaphore counts to track resources could be negatively impacted by
this. We'll see.
- console assert fix: implemented a different type of fbcon
RT-preemption handling variant, this could solve the assert reported
by Amit Shah.
- debugging improvement: implemented a sequence counter for max latency
traces. This has the advantage of solving the 'slow console on SMP
problem': the latency-timing code used to get confused by another CPU
printing a timing message to a slow console and thus delaying that
other CPU. Now any latency that gets generated while a maximum is
printed is skipped.
- further shrunk the non-debug size of struct rt_mutex by moving the
save_state logic into the debug paths - size is now 4 machine-words.
- fixed CONFIG_HIGHMEM latencies: all atomic-kmap APIs are now wrapped
seemlessly and in a preemptible way.
- implemented an IO-APIC register cache to speed up the IRQ-redirection
latency hotpath. Also, made the POST flush a bit faster.
- disable KGDB if PREEMPT_RT - it's broken for now.
- move some runtime checks to under DEBUG_PREEMPT - this speeds up
CRITICAL_PREEMPT_TIMING.
to create a -V0.7.23 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.23
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread* [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-09 16:05 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.23 Ingo Molnar
@ 2004-11-11 14:44 ` Ingo Molnar
2004-11-11 16:03 ` Gunther Persoons
` (2 more replies)
0 siblings, 3 replies; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 14:44 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
Gunther Persoons, emann, Shane Shrybman, Amit Shah
i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
downloaded from the usual place:
http://redhat.com/~mingo/realtime-preempt/
this release includes fixes, new features and latency improvements.
the biggest change is the threading of the lone remaining non-threaded
external interrupt: the timer interrupt (IRQ#0).
It was not threaded until now because unlike device interrupts the timer
interrupt is quite deeply attached to Linux's architecture, driving
process timing, profiling and the scheduler. I separated these into
stuff that can be done from a thread context and stuff that needs to
execute directly.
Fortunately most of the expensive and latency-generating stuff could be
pushed into the irq thread. As a side-effect this enabled the turning of
rtc_lock and xtime_lock into a mutex. Also, it removed some ugly hacks
from rtc.c and should improve worst-case latencies.
the other bigger change is the reworking of the .config space. Instead
of the deep hierarchy of hard-to-understand technical PREEMPT options,
there's now a flattened out choice of 4 preemption models:
( ) No Forced Preemption (Server)
( ) Voluntary Kernel Preemption (Desktop)
( ) Preemptible Kernel (Low-Latency Desktop)
(X) Complete Preemption (Real-Time)
and updated help texts. Plus for the preemption models where it can be
freely turned off, softirq and hardirq threading is an additional
option.
the third bigger change is the reworking of the tracer to make it easier
to drive it from user-space. There are 3 runtime flags now:
/proc/sys/kernel/trace_enabled (default: 1)
/proc/sys/kernel/trace_user_triggered (default: 0)
/proc/sys/kernel/trace_freerunning (default: 0)
semantics of user-triggered tracing: if enabled then any active tracing
of wakeup and/or critical sections stops and userspace drives start/stop
events via gettimeofday(0,1)/gettimeofday(0,0). The latter saves the
current trace into /proc/latency_trace, the former clears the trace
buffer and starts tracing anew. Doing another gettimeofday(0,1) on an
already running tracer clears the trace and restarts it without saving
the current trace into /proc/latency_trace. Doing a gettimeofday(0,0) on
an already stopped tracer has no effect (i.e. /proc/latency_trace wont
be saved a second time). The tracer does timing for userspace
automatically the same way it does it for the built-in timing
mechanisms, and it can be configured via the preempt_max_latency and
preempt_tresh tunables.
also, wakeup-timing, irq-off and preempt-off critical section timing can
now be done at once again, the /proc/sys/kernel/preempt_wakeup_timing
flag switches between the modes. (default: 1)
other changes since -V0.7.24:
- debug feature: added the RTC-debug patch sanitized by K.R. Foley,
plus further cleanups.
- added upstream fix for kobject related crash, pointed out by Shane
Shrybman.
- cleanup: Kconfig help text fixes from Amit Shah
- latency improvement: on UP-IOAPIC, when redirecting an interrupt, do
not ack the APIC. This is the method used for direct interrupts and
on UP it might as well work out fine. It is certainly faster than
masking/unmasking, making UP-IOAPIC the fastest PIC mode again.
- livelock fix: the timer-irq threading unearthed a seqlock related
livelock scenario, which triggered in do_gettimeoffset() big-time.
The solution is to serialize seqlock readers with writers _iff_ the
seqlock status is 'invalid'. This is a rare event, but when it
happens it saves the day.
- debugging helper: the /proc/sys/kernel/debug_direct_keyboard flag
(default: 0) will hack the keyboard IRQ into being direct. NOTE: the
keyboard in this mode should only be used to access SysRq
functionality that is not possible via the threaded keyboard handler.
The direct keyboard IRQ can crash the system.
- new kernel profiling features: added profile=preempt to profile
whether interrupts hit the kernel in preemptible mode or in a
critical section. Added /proc/sys/kernel/prof_pid to profile a
specific PID only. (default: -1, meaning all tasks profiled) Added
/proc/irq/prof_cpu_mask back.
- robustness improvement: do not report atomicity-warnings during
kernel oopses - it's more important to get the oops out to the
console.
to create a -V0.7.25-0 tree from scratch, the patching order is:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.25-0
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 14:44 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Ingo Molnar
@ 2004-11-11 16:03 ` Gunther Persoons
2004-11-11 16:08 ` Ingo Molnar
2004-11-11 20:56 ` Remi Colinet
2004-11-11 21:38 ` Ingo Molnar
2 siblings, 1 reply; 16+ messages in thread
From: Gunther Persoons @ 2004-11-11 16:03 UTC (permalink / raw)
To: Ingo Molnar, linux-kernel
Ingo Molnar wrote:
>i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>downloaded from the usual place:
>
> http://redhat.com/~mingo/realtime-preempt/
>
>this release includes fixes, new features and latency improvements.
>
>the biggest change is the threading of the lone remaining non-threaded
>external interrupt: the timer interrupt (IRQ#0).
>
>It was not threaded until now because unlike device interrupts the timer
>interrupt is quite deeply attached to Linux's architecture, driving
>process timing, profiling and the scheduler. I separated these into
>stuff that can be done from a thread context and stuff that needs to
>execute directly.
>
>Fortunately most of the expensive and latency-generating stuff could be
>pushed into the irq thread. As a side-effect this enabled the turning of
>rtc_lock and xtime_lock into a mutex. Also, it removed some ugly hacks
>from rtc.c and should improve worst-case latencies.
>
>the other bigger change is the reworking of the .config space. Instead
>of the deep hierarchy of hard-to-understand technical PREEMPT options,
>there's now a flattened out choice of 4 preemption models:
>
> ( ) No Forced Preemption (Server)
> ( ) Voluntary Kernel Preemption (Desktop)
> ( ) Preemptible Kernel (Low-Latency Desktop)
> (X) Complete Preemption (Real-Time)
>
>and updated help texts. Plus for the preemption models where it can be
>freely turned off, softirq and hardirq threading is an additional
>option.
>
>the third bigger change is the reworking of the tracer to make it easier
>to drive it from user-space. There are 3 runtime flags now:
>
> /proc/sys/kernel/trace_enabled (default: 1)
> /proc/sys/kernel/trace_user_triggered (default: 0)
> /proc/sys/kernel/trace_freerunning (default: 0)
>
>semantics of user-triggered tracing: if enabled then any active tracing
>of wakeup and/or critical sections stops and userspace drives start/stop
>events via gettimeofday(0,1)/gettimeofday(0,0). The latter saves the
>current trace into /proc/latency_trace, the former clears the trace
>buffer and starts tracing anew. Doing another gettimeofday(0,1) on an
>already running tracer clears the trace and restarts it without saving
>the current trace into /proc/latency_trace. Doing a gettimeofday(0,0) on
>an already stopped tracer has no effect (i.e. /proc/latency_trace wont
>be saved a second time). The tracer does timing for userspace
>automatically the same way it does it for the built-in timing
>mechanisms, and it can be configured via the preempt_max_latency and
>preempt_tresh tunables.
>
>also, wakeup-timing, irq-off and preempt-off critical section timing can
>now be done at once again, the /proc/sys/kernel/preempt_wakeup_timing
>flag switches between the modes. (default: 1)
>
>other changes since -V0.7.24:
>
> - debug feature: added the RTC-debug patch sanitized by K.R. Foley,
> plus further cleanups.
>
> - added upstream fix for kobject related crash, pointed out by Shane
> Shrybman.
>
> - cleanup: Kconfig help text fixes from Amit Shah
>
> - latency improvement: on UP-IOAPIC, when redirecting an interrupt, do
> not ack the APIC. This is the method used for direct interrupts and
> on UP it might as well work out fine. It is certainly faster than
> masking/unmasking, making UP-IOAPIC the fastest PIC mode again.
>
> - livelock fix: the timer-irq threading unearthed a seqlock related
> livelock scenario, which triggered in do_gettimeoffset() big-time.
> The solution is to serialize seqlock readers with writers _iff_ the
> seqlock status is 'invalid'. This is a rare event, but when it
> happens it saves the day.
>
> - debugging helper: the /proc/sys/kernel/debug_direct_keyboard flag
> (default: 0) will hack the keyboard IRQ into being direct. NOTE: the
> keyboard in this mode should only be used to access SysRq
> functionality that is not possible via the threaded keyboard handler.
> The direct keyboard IRQ can crash the system.
>
> - new kernel profiling features: added profile=preempt to profile
> whether interrupts hit the kernel in preemptible mode or in a
> critical section. Added /proc/sys/kernel/prof_pid to profile a
> specific PID only. (default: -1, meaning all tasks profiled) Added
> /proc/irq/prof_cpu_mask back.
>
> - robustness improvement: do not report atomicity-warnings during
> kernel oopses - it's more important to get the oops out to the
> console.
>
>to create a -V0.7.25-0 tree from scratch, the patching order is:
>
> http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.9.tar.bz2
> http://kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.10-rc1.bz2
> http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.10-rc1/2.6.10-rc1-mm3/2.6.10-rc1-mm3.bz2
> http://redhat.com/~mingo/realtime-preempt/realtime-preempt-2.6.10-rc1-mm3-V0.7.25-0
>
> Ingo
>
>
>
Got 2 times a hard lock up with this one. Happened while i was typing
something and downloading both after 15-20 minutes.
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:03 ` Gunther Persoons
@ 2004-11-11 16:08 ` Ingo Molnar
2004-11-11 16:12 ` Ingo Molnar
2004-11-11 16:16 ` Gunther Persoons
0 siblings, 2 replies; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 16:08 UTC (permalink / raw)
To: Gunther Persoons; +Cc: linux-kernel
* Gunther Persoons <gunther_persoons@spymac.com> wrote:
> Got 2 times a hard lock up with this one. Happened while i was typing
> something and downloading both after 15-20 minutes.
.config?
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:08 ` Ingo Molnar
@ 2004-11-11 16:12 ` Ingo Molnar
2004-11-11 16:25 ` Gunther Persoons
2004-11-11 16:30 ` Ingo Molnar
2004-11-11 16:16 ` Gunther Persoons
1 sibling, 2 replies; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 16:12 UTC (permalink / raw)
To: Gunther Persoons; +Cc: linux-kernel
* Ingo Molnar <mingo@elte.hu> wrote:
> * Gunther Persoons <gunther_persoons@spymac.com> wrote:
>
> > Got 2 times a hard lock up with this one. Happened while i was typing
> > something and downloading both after 15-20 minutes.
>
> .config?
just in case you are using UP-IOAPIC, could you enable CONFIG_SMP (even
if you are running an UP box) and see whether the lockup goes away?
Which was the last -RT kernel that you tried that didnt lock up in this
fashion?
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:12 ` Ingo Molnar
@ 2004-11-11 16:25 ` Gunther Persoons
2004-11-11 16:30 ` Ingo Molnar
1 sibling, 0 replies; 16+ messages in thread
From: Gunther Persoons @ 2004-11-11 16:25 UTC (permalink / raw)
To: Ingo Molnar; +Cc: linux-kernel
Ingo Molnar wrote:
>* Ingo Molnar <mingo@elte.hu> wrote:
>
>
>
>>* Gunther Persoons <gunther_persoons@spymac.com> wrote:
>>
>>
>>
>>>Got 2 times a hard lock up with this one. Happened while i was typing
>>>something and downloading both after 15-20 minutes.
>>>
>>>
>>.config?
>>
>>
>
>just in case you are using UP-IOAPIC, could you enable CONFIG_SMP (even
>if you are running an UP box) and see whether the lockup goes away?
>
>
Ok. Going to build a new kernel.
>Which was the last -RT kernel that you tried that didnt lock up in this
>fashion?
>
>
V0.7.24.
> Ingo
>
>
>
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:12 ` Ingo Molnar
2004-11-11 16:25 ` Gunther Persoons
@ 2004-11-11 16:30 ` Ingo Molnar
2004-11-11 17:36 ` Gunther Persoons
1 sibling, 1 reply; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 16:30 UTC (permalink / raw)
To: Gunther Persoons; +Cc: linux-kernel
* Ingo Molnar <mingo@elte.hu> wrote:
> just in case you are using UP-IOAPIC, could you enable CONFIG_SMP
> (even if you are running an UP box) and see whether the lockup goes
> away? Which was the last -RT kernel that you tried that didnt lock up
> in this fashion?
if with CONFIG_SMP it's more stable, could you try the following: turn
off CONFIG_SMP again and edit arch/i386/kernel/io_apic.c and remove this
string:
&& defined(CONFIG_SMP)
(there should be only one occurence of this string.)
this will turn the previous IO-APIC logic (used in -V0.7.24) back on.
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:30 ` Ingo Molnar
@ 2004-11-11 17:36 ` Gunther Persoons
0 siblings, 0 replies; 16+ messages in thread
From: Gunther Persoons @ 2004-11-11 17:36 UTC (permalink / raw)
To: Ingo Molnar; +Cc: linux-kernel
Ingo Molnar wrote:
>* Ingo Molnar <mingo@elte.hu> wrote:
>
>
>
>>just in case you are using UP-IOAPIC, could you enable CONFIG_SMP
>>(even if you are running an UP box) and see whether the lockup goes
>>away? Which was the last -RT kernel that you tried that didnt lock up
>>in this fashion?
>>
>>
>
>if with CONFIG_SMP it's more stable, could you try the following: turn
>off CONFIG_SMP again and edit arch/i386/kernel/io_apic.c and remove this
>string:
>
> && defined(CONFIG_SMP)
>
>(there should be only one occurence of this string.)
>
>this will turn the previous IO-APIC logic (used in -V0.7.24) back on.
>
> Ingo
>
>
>
It locked up after 20 minutes with CONFIG_SMP enabled.
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 16:08 ` Ingo Molnar
2004-11-11 16:12 ` Ingo Molnar
@ 2004-11-11 16:16 ` Gunther Persoons
1 sibling, 0 replies; 16+ messages in thread
From: Gunther Persoons @ 2004-11-11 16:16 UTC (permalink / raw)
To: Ingo Molnar; +Cc: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 259 bytes --]
Ingo Molnar wrote:
>* Gunther Persoons <gunther_persoons@spymac.com> wrote:
>
>
>
>>Got 2 times a hard lock up with this one. Happened while i was typing
>>something and downloading both after 15-20 minutes.
>>
>>
>
>.config?
>
> Ingo
>
>
>
Attached
[-- Attachment #2: config --]
[-- Type: text/plain, Size: 31696 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.10-rc1-mm3-RT-V0.7.25-0
# Thu Nov 11 16:07:49 2004
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
# CONFIG_SMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT_DESKTOP is not set
CONFIG_PREEMPT_RT=y
CONFIG_PREEMPT=y
CONFIG_PREEMPT_SOFTIRQS=y
CONFIG_PREEMPT_HARDIRQS=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_UP_APIC=y
# CONFIG_X86_UP_IOAPIC is not set
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_HAVE_DEC_LOCK=y
# CONFIG_REGPARM is not set
#
# Performance-monitoring counters support
#
# CONFIG_PERFCTR is not set
CONFIG_KERN_PHYS_OFFSET=1
# CONFIG_KEXEC is not set
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_SOFTWARE_SUSPEND is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
CONFIG_ACPI_THINKPAD=m
CONFIG_ACPI_IBM=m
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_X86_PM_TIMER is not set
# CONFIG_ACPI_CONTAINER is not set
#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_DEBUG is not set
# CONFIG_CPU_FREQ_PROC_INTF is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_24_API is not set
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
CONFIG_CPU_FREQ_TABLE=y
#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=y
CONFIG_X86_POWERNOW_K6=y
CONFIG_X86_POWERNOW_K7=y
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_GX_SUSPMOD=y
CONFIG_X86_SPEEDSTEP_CENTRINO=y
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=y
CONFIG_X86_SPEEDSTEP_SMI=y
CONFIG_X86_P4_CLOCKMOD=y
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
CONFIG_X86_LONGRUN=y
CONFIG_X86_LONGHAUL=y
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=y
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
# CONFIG_PCMCIA_OBSOLETE is not set
CONFIG_PCMCIA=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=m
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
CONFIG_PCMCIA_PROBE=y
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
# CONFIG_PNPACPI is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_LBD=y
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
CONFIG_BLK_DEV_HPT34X=y
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=y
# CONFIG_PDC202XX_BURST is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
CONFIG_BLK_DEV_TRM290=y
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=m
# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
# CONFIG_SCSI_FC_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLOGIC_1280_1040 is not set
CONFIG_SCSI_QLA2XXX=m
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
CONFIG_FUSION=m
CONFIG_FUSION_MAX_SGE=40
CONFIG_FUSION_CTL=m
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
# CONFIG_IEEE1394_EXTRA_CONFIG_ROMS is not set
#
# Device Drivers
#
#
# Texas Instruments PCILynx requires I2C
#
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
# CONFIG_IEEE1394_VIDEO1394 is not set
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_KGDBOE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
CONFIG_LANCE=m
CONFIG_NET_VENDOR_SMC=y
# CONFIG_WD80x3 is not set
# CONFIG_ULTRA is not set
# CONFIG_SMC9194 is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
CONFIG_HP100=m
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_AMD8111_ETH=m
# CONFIG_AMD8111E_NAPI is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
CONFIG_APRICOT=m
CONFIG_B44=m
CONFIG_FORCEDETH=m
# CONFIG_CS89x0 is not set
CONFIG_DGRS=m
# CONFIG_EEPRO100 is not set
CONFIG_E100=m
# CONFIG_E100_NAPI is not set
# CONFIG_FEALNX is not set
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
# CONFIG_DL2K is not set
CONFIG_E1000=m
# CONFIG_E1000_NAPI is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
# CONFIG_R8169_NAPI is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=m
#
# Ethernet (10000 Mbit)
#
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
# CONFIG_ARLAN is not set
# CONFIG_WAVELAN is not set
# CONFIG_PCMCIA_WAVELAN is not set
# CONFIG_PCMCIA_NETWAVE is not set
#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set
#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_AIRO_CS=m
# CONFIG_PCMCIA_WL3501 is not set
#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
CONFIG_NET_WIRELESS=y
#
# PCMCIA network device support
#
# CONFIG_NET_PCMCIA is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
CONFIG_GAMEPORT=m
CONFIG_SOUND_GAMEPORT=m
# CONFIG_GAMEPORT_NS558 is not set
# CONFIG_GAMEPORT_L4 is not set
# CONFIG_GAMEPORT_EMU10K1 is not set
# CONFIG_GAMEPORT_VORTEX is not set
# CONFIG_GAMEPORT_FM801 is not set
# CONFIG_GAMEPORT_CS461x is not set
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_CS is not set
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_NVRAM=y
CONFIG_RTC=y
CONFIG_RTC_HISTOGRAM=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_SONYPI=m
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
CONFIG_AGP_ALI=m
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
CONFIG_AGP_AMD64=m
CONFIG_AGP_INTEL=m
# CONFIG_AGP_INTEL_MCH is not set
CONFIG_AGP_NVIDIA=m
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HPET is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_RTCTIMER is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# ISA devices
#
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_ALI5451=m
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
CONFIG_SND_AZT3328=m
# CONFIG_SND_BT87X is not set
CONFIG_SND_CS46XX=m
# CONFIG_SND_CS46XX_NEW_DSP is not set
CONFIG_SND_CS4281=m
CONFIG_SND_EMU10K1=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
CONFIG_SND_NM256=m
# CONFIG_SND_RME32 is not set
CONFIG_SND_RME96=m
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
CONFIG_SND_TRIDENT=m
CONFIG_SND_YMFPCI=m
CONFIG_SND_ALS4000=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
CONFIG_SND_VIA82XX=m
# CONFIG_SND_VX222 is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_VXP440 is not set
# CONFIG_SND_PDAUDIOCF is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_RW_DETECT is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_TEST is not set
#
# USB ATM/DSL drivers
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISER4_FS=m
CONFIG_REISER4_LARGE_KEY=y
# CONFIG_REISER4_CHECK is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# Caches
#
# CONFIG_FSCACHE is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V4 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_POSIX is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_WAKEUP_TIMING=y
CONFIG_PREEMPT_TRACE=y
# CONFIG_CRITICAL_PREEMPT_TIMING is not set
# CONFIG_CRITICAL_IRQSOFF_TIMING is not set
CONFIG_LATENCY_TIMING=y
# CONFIG_LATENCY_TRACE is not set
CONFIG_RT_DEADLOCK_DETECT=y
# CONFIG_USE_FRAME_POINTER is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES_586 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
CONFIG_CRYPTO_ARC4=m
# CONFIG_CRYPTO_KHAZAD is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_PC=y
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 14:44 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Ingo Molnar
2004-11-11 16:03 ` Gunther Persoons
@ 2004-11-11 20:56 ` Remi Colinet
2004-11-11 18:12 ` K.R. Foley
2004-11-11 18:42 ` K.R. Foley
2004-11-11 21:38 ` Ingo Molnar
2 siblings, 2 replies; 16+ messages in thread
From: Remi Colinet @ 2004-11-11 20:56 UTC (permalink / raw)
To: Ingo Molnar; +Cc: LKML
[-- Attachment #1: Type: text/plain, Size: 893 bytes --]
Ingo Molnar wrote:
>i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>downloaded from the usual place:
>
> http://redhat.com/~mingo/realtime-preempt/
>
>
>
>
Hi,
I'm getting the following warning with V0.7.25-0
INSTALL sound/drivers/opl3/snd-opl3-lib.ko
INSTALL sound/drivers/opl3/snd-opl3-synth.ko
INSTALL sound/drivers/snd-dummy.ko
INSTALL sound/drivers/snd-mtpav.ko
INSTALL sound/drivers/snd-serial-u16550.ko
INSTALL sound/drivers/snd-virmidi.ko
INSTALL sound/pci/snd-sonicvibes.ko
if [ -r System.map ]; then /sbin/depmod -ae -F System.map
2.6.10-rc1-mm3-RT-V0.7.25-0; fi
WARNING:
/lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
needs unknown symbol rtc_close_event
WARNING:
/lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
needs unknown symbol rtc_open_event
[root@tigre01 im]#
.config file attached
Remi
[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 42168 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.10-rc1-mm3-RT-V0.7.25-0
# Thu Nov 11 19:53:49 2004
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_SYSCTL=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CPUSETS=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
CONFIG_MPENTIUMIII=y
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_SMP=y
CONFIG_NR_CPUS=8
# CONFIG_SCHED_SMT is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT_DESKTOP is not set
CONFIG_PREEMPT_RT=y
CONFIG_PREEMPT=y
CONFIG_PREEMPT_SOFTIRQS=y
CONFIG_PREEMPT_HARDIRQS=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_IRQBALANCE=y
CONFIG_HAVE_DEC_LOCK=y
#
# Performance-monitoring counters support
#
CONFIG_PERFCTR=y
CONFIG_PERFCTR_INIT_TESTS=y
CONFIG_PERFCTR_VIRTUAL=y
CONFIG_PERFCTR_INTERRUPT_SUPPORT=y
CONFIG_PERFCTR_CPUS_FORBIDDEN_MASK=y
CONFIG_KERN_PHYS_OFFSET=1
# CONFIG_KEXEC is not set
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_DEBUG=y
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
# CONFIG_ACPI_VIDEO is not set
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
# CONFIG_ACPI_HOTPLUG_CPU is not set
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
CONFIG_ACPI_THINKPAD=m
CONFIG_ACPI_IBM=y
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
# CONFIG_ACPI_CONTAINER is not set
#
# APM (Advanced Power Management) BIOS Support
#
# CONFIG_APM is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_PROC_INTF=m
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=m
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_24_API=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_TABLE=y
#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_SMI=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_CPUFREQ_NFORCE2=m
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
#
# shared options
#
CONFIG_X86_ACPI_CPUFREQ_PROC_INTF=y
CONFIG_X86_SPEEDSTEP_LIB=m
CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_EISA=y
CONFIG_EISA_VLB_PRIMING=y
CONFIG_EISA_PCI_EISA=y
CONFIG_EISA_VIRTUAL_ROOT=y
CONFIG_EISA_NAMES=y
CONFIG_MCA=y
CONFIG_MCA_LEGACY=y
CONFIG_MCA_PROC_FS=y
CONFIG_SCx200=m
CONFIG_HOTPLUG_CPU=y
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
CONFIG_PCMCIA_DEBUG=y
CONFIG_PCMCIA_OBSOLETE=y
CONFIG_PCMCIA=m
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=m
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
CONFIG_PCMCIA_PROBE=y
#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=m
CONFIG_HOTPLUG_PCI_FAKE=m
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
CONFIG_HOTPLUG_PCI_ACPI=m
# CONFIG_HOTPLUG_PCI_ACPI_IBM is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
CONFIG_HOTPLUG_PCI_PCIE=m
CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE=y
# CONFIG_HOTPLUG_PCI_SHPC is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Device Drivers
#
#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
CONFIG_DEBUG_DRIVER=y
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set
#
# Plug and Play support
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_PS2 is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
CONFIG_BLK_DEV_UB=m
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_INITRAMFS_SOURCE=""
CONFIG_LBD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
CONFIG_BLK_DEV_IDE_SATA=y
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=m
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_IDEDMA_FORCED=y
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
CONFIG_SCSI_FC_ATTRS=m
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
CONFIG_SCSI_SATA=y
CONFIG_SCSI_SATA_AHCI=m
# CONFIG_SCSI_SATA_SVW is not set
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_FD_MCS is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IBMMCA is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR_D700 is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_NCR_Q720 is not set
# CONFIG_SCSI_MCA_53C9X is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLOGIC_1280_1040 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
CONFIG_SCSI_DEBUG=m
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=m
CONFIG_UNIX=y
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
CONFIG_ARPD=y
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TUNNEL=m
# CONFIG_IP_TCPDIAG is not set
# CONFIG_IP_TCPDIAG_IPV6 is not set
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
CONFIG_NETFILTER=y
CONFIG_NETFILTER_DEBUG=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_CT_ACCT=y
# CONFIG_IP_NF_CONNTRACK_MARK is not set
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
# CONFIG_IP_NF_MATCH_PKTTYPE is not set
# CONFIG_IP_NF_MATCH_MARK is not set
# CONFIG_IP_NF_MATCH_MULTIPORT is not set
# CONFIG_IP_NF_MATCH_TOS is not set
# CONFIG_IP_NF_MATCH_RECENT is not set
# CONFIG_IP_NF_MATCH_ECN is not set
# CONFIG_IP_NF_MATCH_DSCP is not set
# CONFIG_IP_NF_MATCH_AH_ESP is not set
# CONFIG_IP_NF_MATCH_LENGTH is not set
# CONFIG_IP_NF_MATCH_TTL is not set
# CONFIG_IP_NF_MATCH_TCPMSS is not set
# CONFIG_IP_NF_MATCH_HELPER is not set
# CONFIG_IP_NF_MATCH_STATE is not set
# CONFIG_IP_NF_MATCH_CONNTRACK is not set
# CONFIG_IP_NF_MATCH_OWNER is not set
# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
# CONFIG_IP_NF_MATCH_REALM is not set
# CONFIG_IP_NF_MATCH_SCTP is not set
# CONFIG_IP_NF_MATCH_COMMENT is not set
# CONFIG_IP_NF_MATCH_HASHLIMIT is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
# CONFIG_IP_NF_TARGET_ULOG is not set
# CONFIG_IP_NF_TARGET_TCPMSS is not set
# CONFIG_IP_NF_NAT is not set
# CONFIG_IP_NF_MANGLE is not set
# CONFIG_IP_NF_RAW is not set
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
#
# IPv6: Netfilter Configuration
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_LIMIT=m
CONFIG_IP6_NF_MATCH_MAC=m
CONFIG_IP6_NF_MATCH_RT=m
# CONFIG_IP6_NF_MATCH_OPTS is not set
# CONFIG_IP6_NF_MATCH_FRAG is not set
# CONFIG_IP6_NF_MATCH_HL is not set
# CONFIG_IP6_NF_MATCH_MULTIPORT is not set
# CONFIG_IP6_NF_MATCH_OWNER is not set
# CONFIG_IP6_NF_MATCH_MARK is not set
# CONFIG_IP6_NF_MATCH_IPV6HEADER is not set
# CONFIG_IP6_NF_MATCH_AHESP is not set
# CONFIG_IP6_NF_MATCH_LENGTH is not set
# CONFIG_IP6_NF_MATCH_EUI64 is not set
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
# CONFIG_IP6_NF_MANGLE is not set
# CONFIG_IP6_NF_RAW is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
CONFIG_ATM=m
CONFIG_ATM_CLIP=m
CONFIG_ATM_CLIP_NO_ICMP=y
CONFIG_ATM_LANE=m
CONFIG_ATM_MPOA=m
CONFIG_ATM_BR2684=m
CONFIG_ATM_BR2684_IPFILTER=y
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
CONFIG_LLC=m
CONFIG_LLC2=m
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_KGDBOE is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
CONFIG_EL3=m
# CONFIG_3C515 is not set
# CONFIG_ELMC is not set
# CONFIG_ELMC_II is not set
# CONFIG_VORTEX is not set
# CONFIG_TYPHOON is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
# CONFIG_SKMC is not set
# CONFIG_NE2_MCA is not set
# CONFIG_IBMLANA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
CONFIG_EEPRO100=m
CONFIG_E100=m
# CONFIG_E100_NAPI is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
# CONFIG_ARLAN is not set
# CONFIG_WAVELAN is not set
# CONFIG_PCMCIA_WAVELAN is not set
# CONFIG_PCMCIA_NETWAVE is not set
#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set
#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set
#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
CONFIG_NET_WIRELESS=y
#
# PCMCIA network device support
#
# CONFIG_NET_PCMCIA is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# ATM drivers
#
CONFIG_ATM_TCP=m
# CONFIG_ATM_LANAI is not set
# CONFIG_ATM_ENI is not set
# CONFIG_ATM_FIRESTREAM is not set
# CONFIG_ATM_ZATM is not set
# CONFIG_ATM_NICSTAR is not set
# CONFIG_ATM_IDT77252 is not set
# CONFIG_ATM_AMBASSADOR is not set
# CONFIG_ATM_HORIZON is not set
# CONFIG_ATM_IA is not set
# CONFIG_ATM_FORE200E_MAYBE is not set
# CONFIG_ATM_HE is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
# CONFIG_SERIO_CT82C710 is not set
CONFIG_SERIO_PARKBD=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
CONFIG_N_HDLC=m
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
# CONFIG_SERIAL_8250_CS is not set
CONFIG_SERIAL_8250_ACPI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_MULTIPORT is not set
# CONFIG_SERIAL_8250_RSA is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=y
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
# CONFIG_TIPAR is not set
#
# IPMI
#
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_PANIC_EVENT=y
CONFIG_IPMI_PANIC_STRING=y
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
# CONFIG_ALIM1535_WDT is not set
# CONFIG_ALIM7101_WDT is not set
# CONFIG_SC520_WDT is not set
# CONFIG_EUROTECH_WDT is not set
# CONFIG_IB700_WDT is not set
# CONFIG_WAFER_WDT is not set
# CONFIG_I8XX_TCO is not set
# CONFIG_SC1200_WDT is not set
# CONFIG_SCx200_WDT is not set
# CONFIG_60XX_WDT is not set
# CONFIG_CPU5_WDT is not set
# CONFIG_W83627HF_WDT is not set
# CONFIG_W83877F_WDT is not set
# CONFIG_MACHZ_WDT is not set
#
# ISA-based Watchdog Cards
#
# CONFIG_PCWATCHDOG is not set
# CONFIG_MIXCOMWD is not set
# CONFIG_WDT is not set
#
# PCI-based Watchdog Cards
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set
#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_HW_RANDOM=m
CONFIG_NVRAM=m
CONFIG_RTC=m
CONFIG_RTC_HISTOGRAM=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=y
# CONFIG_AGP_INTEL_MCH is not set
CONFIG_AGP_NVIDIA=m
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_SCx200_GPIO is not set
CONFIG_RAW_DRIVER=m
CONFIG_HPET=y
CONFIG_HPET_RTC_IRQ=y
CONFIG_HPET_MMAP=y
CONFIG_MAX_RAW_DEVS=256
CONFIG_HANGCHECK_TIMER=m
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_ELEKTOR is not set
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
# CONFIG_I2C_ISA is not set
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
CONFIG_I2C_PIIX4=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Hardware Sensors Chip support
#
CONFIG_I2C_SENSOR=m
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_IT87 is not set
CONFIG_SENSORS_LM75=m
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
#
# Other I2C Chip support
#
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
CONFIG_I2C_DEBUG_CORE=y
CONFIG_I2C_DEBUG_ALGO=y
CONFIG_I2C_DEBUG_BUS=y
CONFIG_I2C_DEBUG_CHIP=y
#
# Dallas's 1-wire bus
#
CONFIG_W1=m
# CONFIG_W1_MATROX is not set
# CONFIG_W1_DS9490 is not set
CONFIG_W1_THERM=m
# CONFIG_W1_SMEM is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
#
# Video For Linux
#
#
# Video Adapters
#
# CONFIG_VIDEO_BT848 is not set
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_ZR36120 is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set
# CONFIG_VIDEO_OVCAMCHIP is not set
#
# Radio Adapters
#
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_RTRACK is not set
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_GEMTEK is not set
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_SF16FMR2 is not set
# CONFIG_RADIO_TERRATEC is not set
# CONFIG_RADIO_TRUST is not set
# CONFIG_RADIO_TYPHOON is not set
# CONFIG_RADIO_ZOLTRIX is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
CONFIG_FB_RIVA=m
# CONFIG_FB_RIVA_I2C is not set
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_I810=m
CONFIG_FB_I810_GTF=y
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=m
CONFIG_FB_SAVAGE_ACCEL=m
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_MDA_CONSOLE=m
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=m
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
CONFIG_FONT_MINI_4x6=y
CONFIG_FONT_SUN8x16=y
# CONFIG_FONT_SUN12x22 is not set
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
# CONFIG_LOGO_LINUX_VGA16 is not set
# CONFIG_LOGO_LINUX_CLUT224 is not set
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=y
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
CONFIG_SND_DEBUG_MEMORY=y
CONFIG_SND_DEBUG_DETECT=y
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
#
# ISA devices
#
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
CONFIG_SND_AC97_CODEC=y
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_INTEL8X0M is not set
CONFIG_SND_SONICVIBES=m
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VX222 is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_VXP440 is not set
# CONFIG_SND_PDAUDIOCF is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB=y
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_STORAGE is not set
#
# USB Input Devices
#
# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set
#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_TEST is not set
#
# USB ATM/DSL drivers
#
# CONFIG_USB_ATM is not set
# CONFIG_USB_SPEEDTOUCH is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=y
CONFIG_JBD_DEBUG=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=y
#
# Caches
#
CONFIG_FSCACHE=m
CONFIG_CACHEFS=m
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS_XATTR=y
CONFIG_DEVPTS_FS_SECURITY=y
CONFIG_TMPFS=y
CONFIG_TMPFS_XATTR=y
CONFIG_TMPFS_SECURITY=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
# CONFIG_ROOT_NFS is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Profiling support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_SCHEDSTATS=y
# CONFIG_DEBUG_SLAB is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_WAKEUP_TIMING=y
CONFIG_PREEMPT_TRACE=y
CONFIG_CRITICAL_PREEMPT_TIMING=y
CONFIG_CRITICAL_IRQSOFF_TIMING=y
CONFIG_CRITICAL_TIMING=y
CONFIG_LATENCY_TIMING=y
CONFIG_LATENCY_TRACE=y
CONFIG_MCOUNT=y
CONFIG_RT_DEADLOCK_DETECT=y
CONFIG_DEBUG_KOBJECT=y
CONFIG_DEBUG_INFO=y
CONFIG_FRAME_POINTER=y
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_KPROBES=y
CONFIG_DEBUG_STACK_USAGE=y
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_CAPABILITIES=m
CONFIG_SECURITY_ROOTPLUG=m
# CONFIG_SECURITY_SECLVL is not set
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1
CONFIG_SECURITY_SELINUX_DISABLE=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_SECURITY_SELINUX_MLS=y
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=m
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES_586 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_TEST=m
#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_PC=y
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 20:56 ` Remi Colinet
@ 2004-11-11 18:12 ` K.R. Foley
2004-11-11 18:42 ` K.R. Foley
1 sibling, 0 replies; 16+ messages in thread
From: K.R. Foley @ 2004-11-11 18:12 UTC (permalink / raw)
To: Remi Colinet; +Cc: Ingo Molnar, LKML
Remi Colinet wrote:
> Ingo Molnar wrote:
>
>> i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>> downloaded from the usual place:
>>
>> http://redhat.com/~mingo/realtime-preempt/
>>
>>
>>
>>
> Hi,
>
> I'm getting the following warning with V0.7.25-0
>
> INSTALL sound/drivers/opl3/snd-opl3-lib.ko
> INSTALL sound/drivers/opl3/snd-opl3-synth.ko
> INSTALL sound/drivers/snd-dummy.ko
> INSTALL sound/drivers/snd-mtpav.ko
> INSTALL sound/drivers/snd-serial-u16550.ko
> INSTALL sound/drivers/snd-virmidi.ko
> INSTALL sound/pci/snd-sonicvibes.ko
> if [ -r System.map ]; then /sbin/depmod -ae -F System.map
> 2.6.10-rc1-mm3-RT-V0.7.25-0; fi
> WARNING:
> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
> needs unknown symbol rtc_close_event
> WARNING:
> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
> needs unknown symbol rtc_open_event
> [root@tigre01 im]#
>
> .config file attached
>
> Remi
>
Does the patch below fix this?
kr
--- linux-2.6.10-rc1-mm3/drivers/char/rtc.c.orig 2004-11-11
11:35:00.898841565 -0600
+++ linux-2.6.10-rc1-mm3/drivers/char/rtc.c 2004-11-11
12:07:54.019642611 -0600
@@ -863,7 +863,9 @@
if(rtc_status & RTC_IS_OPEN)
goto out_busy;
+#ifdef RTC_IRQ
rtc_open_event();
+#endif
rtc_status |= RTC_IS_OPEN;
rtc_irq_data = 0;
@@ -920,7 +922,9 @@
rtc_irq_data = 0;
rtc_status &= ~RTC_IS_OPEN;
spin_unlock_irq (&rtc_lock);
+#ifdef RTC_IRQ
rtc_close_event();
+#endif
return 0;
}
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 20:56 ` Remi Colinet
2004-11-11 18:12 ` K.R. Foley
@ 2004-11-11 18:42 ` K.R. Foley
2004-11-11 21:41 ` Ingo Molnar
2004-11-12 3:49 ` Remi Colinet
1 sibling, 2 replies; 16+ messages in thread
From: K.R. Foley @ 2004-11-11 18:42 UTC (permalink / raw)
To: Remi Colinet; +Cc: Ingo Molnar, LKML
[-- Attachment #1: Type: text/plain, Size: 1042 bytes --]
Remi Colinet wrote:
> Ingo Molnar wrote:
>
>> i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>> downloaded from the usual place:
>>
>> http://redhat.com/~mingo/realtime-preempt/
>>
>>
>>
>>
> Hi,
>
> I'm getting the following warning with V0.7.25-0
>
> INSTALL sound/drivers/opl3/snd-opl3-lib.ko
> INSTALL sound/drivers/opl3/snd-opl3-synth.ko
> INSTALL sound/drivers/snd-dummy.ko
> INSTALL sound/drivers/snd-mtpav.ko
> INSTALL sound/drivers/snd-serial-u16550.ko
> INSTALL sound/drivers/snd-virmidi.ko
> INSTALL sound/pci/snd-sonicvibes.ko
> if [ -r System.map ]; then /sbin/depmod -ae -F System.map
> 2.6.10-rc1-mm3-RT-V0.7.25-0; fi
> WARNING:
> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
> needs unknown symbol rtc_close_event
> WARNING:
> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
> needs unknown symbol rtc_open_event
> [root@tigre01 im]#
>
> .config file attached
>
> Remi
>
Damn. Here is the patch again. Last one was hosed by wrap. Sorry.
kr
[-- Attachment #2: rtc.fix --]
[-- Type: text/plain, Size: 494 bytes --]
--- linux-2.6.10-rc1-mm3/drivers/char/rtc.c.orig 2004-11-11 11:35:00.898841565 -0600
+++ linux-2.6.10-rc1-mm3/drivers/char/rtc.c 2004-11-11 12:07:54.019642611 -0600
@@ -863,7 +863,9 @@
if(rtc_status & RTC_IS_OPEN)
goto out_busy;
+#ifdef RTC_IRQ
rtc_open_event();
+#endif
rtc_status |= RTC_IS_OPEN;
rtc_irq_data = 0;
@@ -920,7 +922,9 @@
rtc_irq_data = 0;
rtc_status &= ~RTC_IS_OPEN;
spin_unlock_irq (&rtc_lock);
+#ifdef RTC_IRQ
rtc_close_event();
+#endif
return 0;
}
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 18:42 ` K.R. Foley
@ 2004-11-11 21:41 ` Ingo Molnar
2004-11-12 3:49 ` Remi Colinet
1 sibling, 0 replies; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 21:41 UTC (permalink / raw)
To: K.R. Foley; +Cc: Remi Colinet, LKML
* K.R. Foley <kr@cybsft.com> wrote:
> +#ifdef RTC_IRQ
> rtc_open_event();
> +#endif
> +#ifdef RTC_IRQ
> rtc_close_event();
> +#endif
indeed. I fixed it a bit differently in my tree, will upload a new patch
soon.
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 18:42 ` K.R. Foley
2004-11-11 21:41 ` Ingo Molnar
@ 2004-11-12 3:49 ` Remi Colinet
1 sibling, 0 replies; 16+ messages in thread
From: Remi Colinet @ 2004-11-12 3:49 UTC (permalink / raw)
To: K.R. Foley; +Cc: Ingo Molnar, LKML
K.R. Foley wrote:
> Remi Colinet wrote:
>
>> Ingo Molnar wrote:
>>
>>> i have released the -V0.7.25-0 Real-Time Preemption patch, which can be
>>> downloaded from the usual place:
>>>
>>> http://redhat.com/~mingo/realtime-preempt/
>>>
>> Hi,
>>
>> I'm getting the following warning with V0.7.25-0
>>
>> INSTALL sound/drivers/opl3/snd-opl3-lib.ko
>> INSTALL sound/drivers/opl3/snd-opl3-synth.ko
>> INSTALL sound/drivers/snd-dummy.ko
>> INSTALL sound/drivers/snd-mtpav.ko
>> INSTALL sound/drivers/snd-serial-u16550.ko
>> INSTALL sound/drivers/snd-virmidi.ko
>> INSTALL sound/pci/snd-sonicvibes.ko
>> if [ -r System.map ]; then /sbin/depmod -ae -F System.map
>> 2.6.10-rc1-mm3-RT-V0.7.25-0; fi
>> WARNING:
>> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
>> needs unknown symbol rtc_close_event
>> WARNING:
>> /lib/modules/2.6.10-rc1-mm3-RT-V0.7.25-0/kernel/drivers/char/rtc.ko
>> needs unknown symbol rtc_open_event
>> [root@tigre01 im]#
>>
>> .config file attached
>>
>> Remi
>
>
> Damn. Here is the patch again. Last one was hosed by wrap. Sorry.
>
> kr
Solved with V0.7.25-1
Thanks
Remi
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0
2004-11-11 14:44 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Ingo Molnar
2004-11-11 16:03 ` Gunther Persoons
2004-11-11 20:56 ` Remi Colinet
@ 2004-11-11 21:38 ` Ingo Molnar
2 siblings, 0 replies; 16+ messages in thread
From: Ingo Molnar @ 2004-11-11 21:38 UTC (permalink / raw)
To: linux-kernel
Cc: Lee Revell, Rui Nuno Capela, Mark_H_Johnson, K.R. Foley,
Bill Huey, Adam Heath, Florian Schmidt, Thomas Gleixner,
Michal Schmidt, Fernando Pablo Lopez-Lezcano, Karsten Wiese,
Gunther Persoons, emann, Shane Shrybman, Amit Shah,
Gunther Persoons
found the bug that i think caused the freezes and deadlocks reported by
Mark and Gunther. Here's the announcement of a debug feature:
> - debugging helper: the /proc/sys/kernel/debug_direct_keyboard flag
> (default: 0) will hack the keyboard IRQ into being direct. NOTE: the
> keyboard in this mode should only be used to access SysRq
> functionality that is not possible via the threaded keyboard handler.
> The direct keyboard IRQ can crash the system.
it turns out i accidentally left debug_direct_keyboard default-enabled
... no wonder it caused lockups!
Ingo
^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2004-11-11 21:51 UTC | newest]
Thread overview: 16+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-11-11 16:46 [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Mark_H_Johnson
2004-11-11 17:31 ` K.R. Foley
-- strict thread matches above, loose matches on Subject: below --
2004-10-22 13:35 [patch] Real-Time Preemption, -RT-2.6.9-rc4-mm1-U9.3 Ingo Molnar
2004-10-22 15:50 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10 Ingo Molnar
2004-10-22 17:56 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-U10.2 Ingo Molnar
2004-10-25 10:40 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0 Ingo Molnar
2004-10-27 0:15 ` [patch] Real-Time Preemption, -RT-2.6.9-mm1-V0.3 Ingo Molnar
2004-11-03 10:58 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm2-V0.7.1 Ingo Molnar
2004-11-06 15:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.18 Ingo Molnar
2004-11-08 9:16 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.19 Ingo Molnar
2004-11-08 16:57 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.21 Ingo Molnar
2004-11-09 16:05 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.23 Ingo Molnar
2004-11-11 14:44 ` [patch] Real-Time Preemption, -RT-2.6.10-rc1-mm3-V0.7.25-0 Ingo Molnar
2004-11-11 16:03 ` Gunther Persoons
2004-11-11 16:08 ` Ingo Molnar
2004-11-11 16:12 ` Ingo Molnar
2004-11-11 16:25 ` Gunther Persoons
2004-11-11 16:30 ` Ingo Molnar
2004-11-11 17:36 ` Gunther Persoons
2004-11-11 16:16 ` Gunther Persoons
2004-11-11 20:56 ` Remi Colinet
2004-11-11 18:12 ` K.R. Foley
2004-11-11 18:42 ` K.R. Foley
2004-11-11 21:41 ` Ingo Molnar
2004-11-12 3:49 ` Remi Colinet
2004-11-11 21:38 ` Ingo Molnar
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).