Sorry but I forgot my .config, I've attached now with other files.
> Today I downloaded and installed the Kernel 2.6.12
> (I use the old .config of kernel 2.6.11.12 but i tried also a new 
> configuration starting from the default config that the make menuconfig 
> generated).
> When I reboot my Slackware 10.1 in Kernel 2.6.12 this is the output of 
> my dmesg:
> 
> bash-3.00$ dmesg
> Linux version 2.6.12 (root@freedom) (gcc version 3.3.5) #1 SMP Sat Jun 
> 18 15:16:59 CEST 2005
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
>  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
>  BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
>  BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
>  BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
>  BIOS-e820: 00000000ffba0000 - 0000000100000000 (reserved)
> 511MB LOWMEM available.
> found SMP MP-table at 000ff780
> On node 0 totalpages: 130864
>   DMA zone: 4096 pages, LIFO batch:1
>   Normal zone: 126768 pages, LIFO batch:31
>   HighMem zone: 0 pages, LIFO batch:1
> DMI 2.3 present.
> ACPI: RSDP (v000 ACPIAM                                ) @ 0x000f9e70
> ACPI: RSDT (v001 A M I  OEMRSDT  0x02000424 MSFT 0x00000097) @ 0x1ff30000
> ACPI: FADT (v002 A M I  OEMFACP  0x02000424 MSFT 0x00000097) @ 0x1ff30200
> ACPI: MADT (v001 A M I  OEMAPIC  0x02000424 MSFT 0x00000097) @ 0x1ff30390
> ACPI: OEMB (v001 A M I  OEMBIOS  0x02000424 MSFT 0x00000097) @ 0x1ff40040
> ACPI: DSDT (v001  P4PSS P4PSS023 0x00000023 INTL 0x02002026) @ 0x00000000
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 15:3 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 15:3 APIC version 20
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode:  Flat.  Using 1 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 20000000 (gap: 20000000:dfba0000)
> Built 1 zonelists
> Kernel command line: ro root=/dev/hda1 vga=792
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> Initializing CPU#0
> PID hash table entries: 2048 (order: 11, 32768 bytes)
> Detected 2999.507 MHz processor.
> Using tsc for high-res timesource
> Console: colour dummy device 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 513212k/523456k available (2918k kernel code, 9684k reserved, 
> 1121k data, 232k init, 0k highmem)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay loop... 5914.62 BogoMIPS (lpj=2957312)
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 
> 0000041d 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 
> 0000041d 00000000 00000000
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: Trace cache: 12K uops, L1 D cache: 16K
> CPU: L2 cache: 1024K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000041d 
> 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU0: Thermal monitoring enabled
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> Calibrating delay loop... 5980.16 BogoMIPS (lpj=2990080)
> CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 
> 0000041d 00000000 00000000
> CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 
> 0000041d 00000000 00000000
> monitor/mwait feature present.
> CPU: Trace cache: 12K uops, L1 D cache: 16K
> CPU: L2 cache: 1024K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000041d 
> 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU1: Thermal monitoring enabled
> CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
> Total of 2 processors activated (11894.78 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 pin1=2 pin2=-1
> checking TSC synchronization across 2 CPUs: passed.
> Brought up 2 CPUs
> CPU0 attaching sched-domain:
>  domain 0: span 03
>   groups: 01 02
>   domain 1: span 03
>    groups: 03
> CPU1 attaching sched-domain:
>  domain 0: span 03
>   groups: 02 01
>   domain 1: span 03
>    groups: 03
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20050309
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
> Boot video device is 0000:01:00.0
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
> disabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
> disabled.
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 13 devices
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
> report
> pnp: 00:09: ioport range 0x680-0x6ff has been reserved
> pnp: 00:09: ioport range 0x290-0x297 has been reserved
> Machine check exception polling timer started.
> audit: initializing netlink socket (disabled)
> audit(1119108222.761:0): initialized
> Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> Initializing Cryptographic API
> vesafb: framebuffer at 0xe0000000, mapped to 0xe0880000, using 4608k, 
> total 131072k
> vesafb: mode is 1024x768x24, linelength=3072, pages=55
> vesafb: protected mode interface info at c000:56cb
> vesafb: scrolling: redraw
> vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
> mtrr: type mismatch for e0000000,8000000 old: write-back new: 
> write-combining
> mtrr: type mismatch for e0000000,4000000 old: write-back new: 
> write-combining
> mtrr: type mismatch for e0000000,2000000 old: write-back new: 
> write-combining
> mtrr: type mismatch for e0000000,1000000 old: write-back new: 
> write-combining
> mtrr: type mismatch for e0000000,800000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,400000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,200000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,100000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,80000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,40000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,20000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,10000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,8000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,4000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,2000 old: write-back new: write-combining
> mtrr: type mismatch for e0000000,1000 old: write-back new: write-combining
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x800  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x400  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x200  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x100  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x80  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x40  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x20  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x10  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x8  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x4  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x2  base: 0xe0000000
> mtrr: size and base must be multiples of 4 kiB
> mtrr: size: 0x1  base: 0xe0000000
> Console: switching to colour frame buffer device 128x48
> fb0: VESA VGA frame buffer device
> lp: driver loaded but no devices found
> Linux agpgart interface v0.101 (c) Dave Jones
> [drm] Initialized drm 1.0.0 20040925
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
> lp0: using parport0 (interrupt-driven).
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ICH5: IDE controller at PCI slot 0000:00:1f.1
> PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
> ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
> ICH5: chipset revision 2
> ICH5: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
>     ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
> Probing IDE interface ide0...
> hda: IC35L060AVV207-0, ATA DISK drive
> hdb: Maxtor 6Y080L0, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: SAMSUNG CD-R/RW DRIVE SW-252F, ATAPI CD/DVD-ROM drive
> hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide4...
> Probing IDE interface ide5...
> hda: max request size: 1024KiB
> hda: 120103200 sectors (61492 MB) w/1821KiB Cache, CHS=16383/255/63, 
> UDMA(100)
> hda: cache flushes supported
>  hda: hda1 hda2 < hda5 hda6 > hda4
> hdb: max request size: 128KiB
> hdb: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, 
> UDMA(100)
> hdb: cache flushes supported
>  hdb: hdb1 hdb2 < hdb5 hdb6 >
> hdc: ATAPI 1X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
> libata version 1.11 loaded.
> usbmon: debugs is not available
> ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 
> EHCI Controller
> ehci_hcd 0000:00:1d.7: debug port 1
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffaffc00
> PCI: cache line size of 128 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> USB Universal Host Controller Interface driver v2.2
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
> UHCI Controller #1
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ef00
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
> UHCI Controller #2
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ef20
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI #3
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef40
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1d.3 to 64
> uhci_hcd 0000:00:1d.3: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
> UHCI Controller #4
> uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
> uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef80
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> usbcore: registered new driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> Advanced Linux Sound Architecture Driver Version 1.0.9rc2  (Thu Mar 24 
> 10:33:39 2005 UTC).
> ALSA device list:
>   No soundcards found.
> oprofile: using NMI interrupt.
> NET: Registered protocol family 2
> IP: routing cache hash table of 2048 buckets, 32Kbytes
> TCP established hash table entries: 32768 (order: 7, 524288 bytes)
> TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
> TCP: Hash tables configured (established 32768 bind 32768)
> ip_conntrack version 2.1 (4089 buckets, 32712 max) - 220 bytes per conntrack
> input: AT Translated Set 2 keyboard on isa0060/serio0
> ip_tables: (C) 2000-2002 Netfilter core team
> ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  
> http://snowman.net/projects/ipt_recent/
> arp_tables: (C) 2002 David S. Miller
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Starting balanced_irq
> ACPI wakeup devices:
> P0P4 MC97 USB1 USB2 USB3 USB4 EUSB PS2K PS2M ILAN
> ACPI: (supports S0 S1 S3 S4 S5)
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 232k freed
> input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
> Adding 530108k swap on /dev/hda5.  Priority:-1 extents:1
> EXT3 FS on hda1, internal journal
> Bluetooth: Core ver 2.7
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: L2CAP ver 2.7
> Bluetooth: L2CAP socket layer initialized
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on hda4, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on hdb6, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> NTFS driver 2.1.22 [Flags: R/W DEBUG MODULE].
> NTFS volume version 3.1.
> NTFS-fs error (device hdb1): ntfs_check_logfile(): The two restart pages 
> in $LogFile do not match.
> NTFS-fs warning (device hdb1): load_system_files(): Failed to load 
> $LogFile.  Will not be able to remount read-write.  Mount in Windows.
> 8139too Fast Ethernet driver 0.9.27
> ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
> eth0: RealTek RTL8139 at 0xd800, 00:0e:a6:b3:89:32, IRQ 22
> eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
> ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> intel8x0_measure_ac97_clock: measured 50202 usecs
> intel8x0: clocking to 48000
> hw_random: RNG not detected
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> shpchp: shpc_init : shpc_cap_offset == 0
> shpchp: shpc_init : shpc_cap_offset == 0
> shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> agpgart: Detected an Intel 865 Chipset.
> agpgart: AGP aperture is 128M @ 0xf0000000
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> hw_random: RNG not detected
> Real Time Clock Driver v1.12
> ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> w83627hf 1-0290: Reading VID from GPIO5
> i2c /dev entries driver
> mtrr: type mismatch for e0000000,8000000 old: write-back new: 
> write-combining
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
> mtrr: type mismatch for f0000000,8000000 old: write-back new: 
> write-combining
> [drm] Initialized radeon 1.16.0 20050311 on minor 0: ATI Technologies 
> Inc RV280 [Radeon 9200 SE]
> mtrr: type mismatch for e0000000,8000000 old: write-back new: 
> write-combining
> agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
> agpgart: reserved bits set in mode 0x1f004a0f. Fixed.
> agpgart: X tried to set rate=x12. Setting to AGP3 x8 mode.
> agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
> [drm] Loading R200 Microcode
> scsi: unknown opcode 0x01
> 
> One of errors that I see in dmesg is "mtrr: type mismatch for 
> e0000000,8000000 old: write-back new: write-combining", I have probably 
> the same problem of the 2.6.12-rc5-mm1 that I found here: 
> http://seclists.org/lists/linux-kernel/2005/Jun/0216.html but my system 
> has only one soundcard (on board).
> 
> Of course I attached my .config , my /proc/cpuinfo (p4 3.0 ghz 
> prescott), my /proc/modules etc...
> I hope can you give me some help or release some patch.
> 
> Thanks,
> Alessandro Arrichiello from Italy.