2 errors in 2.6.12

2 errors in 2.6.12

[Michal Semler]

Hi,

I compiled 2.6.12 and my PV951 TV card doesn't work (tvtime says no signal) 
and my SBLive! plays only on 2 repros Front left and right.

When I booted back to 2.6.11, everything worked like a charm

PLS fix it

Michal

Re: 2 errors in 2.6.12

[Michal Semler]

Hi,

I tested both - problem with SB Live! is fixed, but tuning problem in PV951 
still exist :(


This is what I gets into dmesg:


Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) -> 
IRQ 9
bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
bttv0: using: ProVideo PV951 [card=42,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=1
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: 
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 
(PV951),ta8874z
tvaudio: found pic16c54 (PV951) @ 0x96
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner: Unknown parameter `type'
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> 
IRQ 10

Michal

Dne pá 29. července 2005 6:48 jste napsal(a):
> Michal Semler <cijoml@volny.cz> wrote:
> > Hi,
> >
> > I compiled 2.6.12 and my PV951 TV card doesn't work (tvtime says no
> > signal) and my SBLive! plays only on 2 repros Front left and right.
> >
> > When I booted back to 2.6.11, everything worked like a charm
>
> Are these fixed in 2.6.13-rc4?
>
> If not, please cc linux-kernel when replying, thanks.

-- 
S pozdravem

Michal Semler

Re: 2 errors in 2.6.12

[Andrew Morton]

Michal Semler <cijoml@volny.cz> wrote:
>
>  I tested both - problem with SB Live! is fixed, but tuning problem in PV951 
>  still exist :(
> 
> 
>  This is what I gets into dmesg:
> 
> 
>  Linux video capture interface: v1.00
>  bttv: driver version 0.9.15 loaded
>  bttv: using 8 buffers with 2080k (520 pages) each for capture
>  bttv: Bt8xx card found (0).
>  ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) -> 
>  IRQ 9
>  bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
>  bttv0: using: ProVideo PV951 [card=42,insmod option]
>  bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>  bttv0: using tuner=1
>  bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>  bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>  tvaudio: TV audio decoder + audio/video mux driver
>  tvaudio: known chips: 
>  tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 
>  (PV951),ta8874z
>  tvaudio: found pic16c54 (PV951) @ 0x96
>  bttv0: i2c: checking for TDA9887 @ 0x86... not found
>  tuner: Unknown parameter `type'
>  bttv0: registered device video0
>  bttv0: registered device vbi0
>  bttv0: registered device radio0
>  bttv0: PLL: 28636363 => 35468950 .. ok
>  ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
>  PCI: setting IRQ 10 as level-triggered
>  ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> 
>  IRQ 10

(cc the v4l list)

The above is with 2.6.13-rc4.  2.6.11 was OK.

Re: 2 errors in 2.6.12

[Michael Krufky]

Andrew Morton wrote:

>Michal Semler <cijoml@volny.cz> wrote:
>  
>
>> This is what I gets into dmesg:
>>
>> Linux video capture interface: v1.00
>> bttv: driver version 0.9.15 loaded
>> bttv: using 8 buffers with 2080k (520 pages) each for capture
>> bttv: Bt8xx card found (0).
>> ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) -> 
>> IRQ 9
>> bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
>> bttv0: using: ProVideo PV951 [card=42,insmod option]
>> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>> bttv0: using tuner=1
>> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>> tvaudio: TV audio decoder + audio/video mux driver
>> tvaudio: known chips: 
>> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54 
>> (PV951),ta8874z
>> tvaudio: found pic16c54 (PV951) @ 0x96
>> bttv0: i2c: checking for TDA9887 @ 0x86... not found
>> tuner: Unknown parameter `type'
>> bttv0: registered device video0
>> bttv0: registered device vbi0
>> bttv0: registered device radio0
>> bttv0: PLL: 28636363 => 35468950 .. ok
>> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
>> PCI: setting IRQ 10 as level-triggered
>> ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> 
>> IRQ 10
>>    
>>
>
>(cc the v4l list)
>
>The above is with 2.6.13-rc4.  2.6.11 was OK.
>  
>
Michael-

Please remove the insmod options:

bttv0: using: ProVideo PV951 [card=42,insmod option]

...and show us dmesg output with autodetection.

Also, please try CVS and tell us if you still have the problem... Instructions at:

http://linuxtv.org/v4lwiki/index.php/How_to_build_from_CVS

-- 
Michael Krufky

Re: 2 errors in 2.6.12

[CIJOML]

Hi,

my card is impossible to be autodetected. Valid sections for it's
identification are missing.

I asked for this some time ago. I need to use insmod option.

Michal

On Sun, 31 Jul 2005, Michael Krufky wrote:

> Andrew Morton wrote:
>
> >Michal Semler <cijoml@volny.cz> wrote:
> >
> >
> >> This is what I gets into dmesg:
> >>
> >> Linux video capture interface: v1.00
> >> bttv: driver version 0.9.15 loaded
> >> bttv: using 8 buffers with 2080k (520 pages) each for capture
> >> bttv: Bt8xx card found (0).
> >> ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) ->
> >> IRQ 9
> >> bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
> >> bttv0: using: ProVideo PV951 [card=42,insmod option]
> >> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> >> bttv0: using tuner=1
> >> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> >> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> >> tvaudio: TV audio decoder + audio/video mux driver
> >> tvaudio: known chips:
> >> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
> >> (PV951),ta8874z
> >> tvaudio: found pic16c54 (PV951) @ 0x96
> >> bttv0: i2c: checking for TDA9887 @ 0x86... not found
> >> tuner: Unknown parameter `type'
> >> bttv0: registered device video0
> >> bttv0: registered device vbi0
> >> bttv0: registered device radio0
> >> bttv0: PLL: 28636363 => 35468950 .. ok
> >> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
> >> PCI: setting IRQ 10 as level-triggered
> >> ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) ->
> >> IRQ 10
> >>
> >>
> >
> >(cc the v4l list)
> >
> >The above is with 2.6.13-rc4.  2.6.11 was OK.
> >
> >
> Michael-
>
> Please remove the insmod options:
>
> bttv0: using: ProVideo PV951 [card=42,insmod option]
>
> ...and show us dmesg output with autodetection.
>
> Also, please try CVS and tell us if you still have the problem... Instructions at:
>
> http://linuxtv.org/v4lwiki/index.php/How_to_build_from_CVS
>
> --
> Michael Krufky
>

Re: 2 errors in 2.6.12

[hermann pitton]

Hello,

this one is solved.

Guess we will see similar issues more often for a while.

Cheers,
Hermann


Am Montag, den 01.08.2005, 20:11 +0200 schrieb CIJOML:
> 
> On Mon, 1 Aug 2005, hermann pitton wrote:
> 
> > Am Montag, den 01.08.2005, 11:16 +0200 schrieb CIJOML:
> > > Hi,
> > >
> > > my card is impossible to be autodetected. Valid sections for it's
> > > identification are missing.
> > >
> > > I asked for this some time ago. I need to use insmod option.
> > >
> > > Michal
> >
> > Hi Michal,
> >
> > the "tuner type=N" insmod option is gone away.
> >
> > There has been a warning that it is deprecated for about 1  1/2 years
> > in dmesg. Please remove it from /etc/modprobe.conf or where else it is
> > called and replace it with "options bttv card=N tuner=N", guess you
> 
> AAAAH!!!! This helped!!! Thanks a lot
> after options bttv           card=42 radio=1 tuner=1
> card works! :)
> 
> Linux video capture interface: v1.00
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low)
> -> IRQ 9
> bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio:
> 0xb69fe000
> bttv0: using: ProVideo PV951 [card=42,insmod option]
> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> bttv0: using tuner=1
> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> tvaudio: TV audio decoder + audio/video mux driver
> tvaudio: known chips:
> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
> (PV951),ta8874z
> tvaudio: found pic16c54 (PV951) @ 0x96
> bttv0: i2c: checking for TDA9887 @ 0x86... not found
>  : chip found @ 0xc0 (bt878 #0 [sw])
>  : All bytes are equal. It is not a TEA5767
> tuner 0-0060: type set to 1 (Philips PAL_I (FI1246 and compatibles))
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: registered device radio0
> bttv0: PLL: 28636363 => 35468950 .. ok
> 
> Thanks a lot!
> 
> Michal
> 
> 
> > might use tuner=5, and what else you might need and then "depmod -a".
> > Does this help?
> >
> > Greetings,
> > Hermann
> >
> >
> > > On Sun, 31 Jul 2005, Michael Krufky wrote:
> > >
> > > > Andrew Morton wrote:
> > > >
> > > > >Michal Semler <cijoml@volny.cz> wrote:
> > > > >
> > > > >
> > > > >> This is what I gets into dmesg:
> > > > >>
> > > > >> Linux video capture interface: v1.00
> > > > >> bttv: driver version 0.9.15 loaded
> > > > >> bttv: using 8 buffers with 2080k (520 pages) each for capture
> > > > >> bttv: Bt8xx card found (0).
> > > > >> ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) ->
> > > > >> IRQ 9
> > > > >> bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
> > > > >> bttv0: using: ProVideo PV951 [card=42,insmod option]
> > > > >> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> > > > >> bttv0: using tuner=1
> > > > >> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> > > > >> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> > > > >> tvaudio: TV audio decoder + audio/video mux driver
> > > > >> tvaudio: known chips:
> > > > >> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
> > > > >> (PV951),ta8874z
> > > > >> tvaudio: found pic16c54 (PV951) @ 0x96
> > > > >> bttv0: i2c: checking for TDA9887 @ 0x86... not found
> > > > >> tuner: Unknown parameter `type'
> >               ^^^^^^^^^^^^^^^^^^^^^^^^
[...]

Re: 2 errors in 2.6.12

[Michael Krufky]

Thank you, Hermann.

AKPM (cc re-added) requested that this thread retain cc's to him... so 
he should see that it has been resolved.......

hermann pitton wrote:

>Hello,
>
>this one is solved.
>
>Guess we will see similar issues more often for a while.
>
>Cheers,
>Hermann
>
>
>Am Montag, den 01.08.2005, 20:11 +0200 schrieb CIJOML:
>  
>
>>On Mon, 1 Aug 2005, hermann pitton wrote:
>>
>>    
>>
>>>Am Montag, den 01.08.2005, 11:16 +0200 schrieb CIJOML:
>>>      
>>>
>>>>Hi,
>>>>
>>>>my card is impossible to be autodetected. Valid sections for it's
>>>>identification are missing.
>>>>
>>>>I asked for this some time ago. I need to use insmod option.
>>>>
>>>>Michal
>>>>        
>>>>
>>>Hi Michal,
>>>
>>>the "tuner type=N" insmod option is gone away.
>>>
>>>There has been a warning that it is deprecated for about 1  1/2 years
>>>in dmesg. Please remove it from /etc/modprobe.conf or where else it is
>>>called and replace it with "options bttv card=N tuner=N", guess you
>>>      
>>>
>>AAAAH!!!! This helped!!! Thanks a lot
>>after options bttv           card=42 radio=1 tuner=1
>>card works! :)
>>
>>Linux video capture interface: v1.00
>>bttv: driver version 0.9.15 loaded
>>bttv: using 8 buffers with 2080k (520 pages) each for capture
>>bttv: Bt8xx card found (0).
>>ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low)
>>-> IRQ 9
>>bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio:
>>0xb69fe000
>>bttv0: using: ProVideo PV951 [card=42,insmod option]
>>bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>>bttv0: using tuner=1
>>bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>>bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>>tvaudio: TV audio decoder + audio/video mux driver
>>tvaudio: known chips:
>>tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
>>(PV951),ta8874z
>>tvaudio: found pic16c54 (PV951) @ 0x96
>>bttv0: i2c: checking for TDA9887 @ 0x86... not found
>> : chip found @ 0xc0 (bt878 #0 [sw])
>> : All bytes are equal. It is not a TEA5767
>>tuner 0-0060: type set to 1 (Philips PAL_I (FI1246 and compatibles))
>>bttv0: registered device video0
>>bttv0: registered device vbi0
>>bttv0: registered device radio0
>>bttv0: PLL: 28636363 => 35468950 .. ok
>>
>>Thanks a lot!
>>
>>Michal
>>
>>
>>    
>>
>>>might use tuner=5, and what else you might need and then "depmod -a".
>>>Does this help?
>>>
>>>Greetings,
>>>Hermann
>>>
>>>
>>>      
>>>
>>>>On Sun, 31 Jul 2005, Michael Krufky wrote:
>>>>
>>>>        
>>>>
>>>>>Andrew Morton wrote:
>>>>>
>>>>>          
>>>>>
>>>>>>Michal Semler <cijoml@volny.cz> wrote:
>>>>>>
>>>>>>
>>>>>>            
>>>>>>
>>>>>>>This is what I gets into dmesg:
>>>>>>>
>>>>>>>Linux video capture interface: v1.00
>>>>>>>bttv: driver version 0.9.15 loaded
>>>>>>>bttv: using 8 buffers with 2080k (520 pages) each for capture
>>>>>>>bttv: Bt8xx card found (0).
>>>>>>>ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) ->
>>>>>>>IRQ 9
>>>>>>>bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
>>>>>>>bttv0: using: ProVideo PV951 [card=42,insmod option]
>>>>>>>bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
>>>>>>>bttv0: using tuner=1
>>>>>>>bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>>>>>>>bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>>>>>>>tvaudio: TV audio decoder + audio/video mux driver
>>>>>>>tvaudio: known chips:
>>>>>>>tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
>>>>>>>(PV951),ta8874z
>>>>>>>tvaudio: found pic16c54 (PV951) @ 0x96
>>>>>>>bttv0: i2c: checking for TDA9887 @ 0x86... not found
>>>>>>>tuner: Unknown parameter `type'
>>>>>>>              
>>>>>>>
>>>              ^^^^^^^^^^^^^^^^^^^^^^^^
>>>      
>>>
>[...]
>
>  
>


-- 
Michael Krufky

Re: 2 errors in 2.6.12

[CIJOML]

On Sun, 31 Jul 2005, Michael Krufky wrote:

> Andrew Morton wrote:
>
> >Michal Semler <cijoml@volny.cz> wrote:
> >
> >
> >> This is what I gets into dmesg:
> >>
> >> Linux video capture interface: v1.00
> >> bttv: driver version 0.9.15 loaded
> >> bttv: using 8 buffers with 2080k (520 pages) each for capture
> >> bttv: Bt8xx card found (0).
> >> ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low) ->
> >> IRQ 9
> >> bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio: 0xb69fe000
> >> bttv0: using: ProVideo PV951 [card=42,insmod option]
> >> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> >> bttv0: using tuner=1
> >> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> >> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> >> tvaudio: TV audio decoder + audio/video mux driver
> >> tvaudio: known chips:
> >> tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6320,tea6420,tda8425,pic16c54
> >> (PV951),ta8874z
> >> tvaudio: found pic16c54 (PV951) @ 0x96
> >> bttv0: i2c: checking for TDA9887 @ 0x86... not found
> >> tuner: Unknown parameter `type'
> >> bttv0: registered device video0
> >> bttv0: registered device vbi0
> >> bttv0: registered device radio0
> >> bttv0: PLL: 28636363 => 35468950 .. ok
> >> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
> >> PCI: setting IRQ 10 as level-triggered
> >> ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) ->
> >> IRQ 10
> >>
> >>
> >
> >(cc the v4l list)
> >
> >The above is with 2.6.13-rc4.  2.6.11 was OK.
> >
> >
> Michael-
>
> Please remove the insmod options:
>
> bttv0: using: ProVideo PV951 [card=42,insmod option]
>
> ...and show us dmesg output with autodetection.
>
> Also, please try CVS and tell us if you still have the problem... Instructions at:
>
> http://linuxtv.org/v4lwiki/index.php/How_to_build_from_CVS
>

Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKH] -> GSI 9 (level, low)
-> IRQ 9
bttv0: Bt878 (rev 17) at 0000:01:0b.0, irq: 9, latency: 32, mmio:
0xb69fe000
bttv0: using:  *** UNKNOWN/GENERIC ***  [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom(bttv internal): Huh, no eeprom present (err=-121)?
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bttv0: registered device video0
bttv0: registered device vbi0

Same with CVS - kernel 2.6.11 with my options works for me like hell.
Card is really PV951 - it was written on box also :)

Michal

> --
> Michael Krufky
>
> --
> video4linux-list mailing list
> Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/video4linux-list
>

Re: 2 errors in 2.6.12

[Nick Warne]

 
>and my SBLive! plays only on 2 repros Front left and right.

Yes - I noticed something with my SB Live.  I thought it was me, but going 
through everythnig this morning, I don't think it is.

>From 2.6.11.12 dmesg:

Jun 17 18:39:45 linuxamd kernel: Advanced Linux Sound Architecture Driver 
Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC).
Jun 17 18:39:45 linuxamd kernel: ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 5 
(level, low) -> IRQ 5
Jun 17 18:39:45 linuxamd kernel: ALSA device list:
Jun 17 18:39:45 linuxamd kernel:   #0: Sound Blaster Live! (rev.7, 
serial:0x80611102) at 0xe000, irq 5

And here from new 2.6.12 dmesg:

Jun 18 15:27:41 linuxamd kernel: Advanced Linux Sound Architecture Driver 
Version 1.0.9rc2  (Thu Mar 24 10:33:39 2005 UTC).
Jun 18 15:27:41 linuxamd kernel: PCI: Found IRQ 5 for device 0000:00:0f.0
Jun 18 15:27:41 linuxamd kernel: ALSA device list:
Jun 18 15:27:41 linuxamd kernel:   #0: SB Live [Unknown] (rev.7, 
serial:0x80611102) at 0xe000, irq 5

Something is awry?

Nick
-- 
"When you're chewing on life's gristle,
Don't grumble, Give a whistle..."

Re: 2 errors in 2.6.12

[Nick Warne]

On Sunday 19 June 2005 11:04, you wrote:
> >and my SBLive! plays only on 2 repros Front left and right.
>
> Yes - I noticed something with my SB Live.  I thought it was me, but going
> through everythnig this morning, I don't think it is.
>
> From 2.6.11.12 dmesg:
>
> Jun 17 18:39:45 linuxamd kernel: Advanced Linux Sound Architecture Driver
> Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC).
> Jun 17 18:39:45 linuxamd kernel: ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI
> 5 (level, low) -> IRQ 5
> Jun 17 18:39:45 linuxamd kernel: ALSA device list:
> Jun 17 18:39:45 linuxamd kernel:   #0: Sound Blaster Live! (rev.7,
> serial:0x80611102) at 0xe000, irq 5
>
> And here from new 2.6.12 dmesg:
>
> Jun 18 15:27:41 linuxamd kernel: Advanced Linux Sound Architecture Driver
> Version 1.0.9rc2  (Thu Mar 24 10:33:39 2005 UTC).
> Jun 18 15:27:41 linuxamd kernel: PCI: Found IRQ 5 for device 0000:00:0f.0
> Jun 18 15:27:41 linuxamd kernel: ALSA device list:
> Jun 18 15:27:41 linuxamd kernel:   #0: SB Live [Unknown] (rev.7,
> serial:0x80611102) at 0xe000, irq 5

OK, I have found out why - an alsa-devel patch changed to be more specific on 
the chipset/model - more here:

http://marc.theaimsgroup.com/?l=linux-kernel&m=111209948526203&w=2

It turns out my card isn't in the ID list, so it gets given an 'unknown'.  As 
this changed from 2.6.11.12, alsamixer then reset (effectively a new card!) 
so I had to reset all my mixer settings again - I would look at your mixer 
settings for the surround sound settings (mute etc.).

Here is a page with the ID and chipsets of the cards:

http://www.digit-life.com/articles/livetolive51/

I am going to attempt to add my card into emu10k1_main.c to get it set right:

0 [Unknown        ]: EMU10K1 - SB Live [Unknown]
                     SB Live [Unknown] (rev.7, serial:0x80611102) at 0xe000, 
irq 5

>From that 'livetolive51' page I am told I have:
SB0060 - SBlive! Value (PCI\VEN_1102&DEV_0002&SUBSYS_80611102)

Nick
-- 
"When you're chewing on life's gristle,
Don't grumble, Give a whistle..."

Re: 2 errors in 2.6.12

[Nick Warne]

Replying to myself...

> Here is a page with the ID and chipsets of the cards:
> 
> http://www.digit-life.com/articles/livetolive51/
> 
> I am going to attempt to add my card into emu10k1_main.c to get it set
> right:
> 
> 0 [Unknown        ]: EMU10K1 - SB Live [Unknown]
>                      SB Live [Unknown] (rev.7, serial:0x80611102) at
>                      0xe000,
> irq 5
> 
> From that 'livetolive51' page I am told I have:
> SB0060 - SBlive! Value (PCI\VEN_1102&DEV_0002&SUBSYS_80611102)

This worked fine, but fishing around, I see 'new' cards ID's are added all the 
time:

http://cvs.sourceforge.net/viewcvs.py/alsa/alsa-kernel/pci/emu10k1/emu10k1_main.c?rev=1.58&view=log

so eventually the [UKNOWN] bit will disappear and alsamixer settings will 
remain between different version kernels (2.6.1x[.x]) then.

Nick
-- 
"When you're chewing on life's gristle,
Don't grumble, Give a whistle..."