From: mikep <mikpolniak@adelphia.net>
To: linux-kernel@vger.kernel.org
Subject: SCSI- unexpected disconnect with kernel-2.6.13-r6
Date: Sat, 20 Aug 2005 15:04:27 -0400 [thread overview]
Message-ID: <43077EBB.5060705@adelphia.net> (raw)
I am using a LSIU160/Symbios 53c1010 Ultra3 scsi adapter and it works at
full speed (75 MB/sec) with kernel-2.6.12. And dmesg shows:
kernel: target0:0:0: Beginning Domain Validation
kernel: target0:0:0: asynchronous.
kernel: WIDTH IS 1
kernel: target0:0:0: wide asynchronous.
kernel: target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
kernel: target0:0:0: Ending Domain Validation
kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11
kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
kernel: sym1: open drain IRQ line driver
kernel: sym1: using LOAD/STORE-based firmware.
kernel: sym1: handling phase mismatch from SCRIPTS.
kernel: sym1: SCSI BUS has been reset.
kernel: scsi1 : sym-2.2.0
kernel: libata version 1.11 loaded.
With kernel-2.6.13-r6 the speed drops back to 2.70 MB/sec because of
validation failure and dmesg shows:
kernel: target0:0:0: Beginning Domain Validation
kernel: target0:0:0: asynchronous.
kernel: target0:0:0: wide asynchronous.
kernel: target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (
kernel: sym0: unexpected disconnect
kernel: target0:0:0: Write Buffer failure 700ff
kernel: target0:0:0: Domain Validation Disabing Information units
kernel: 0:0:0:0: phase change 6-7 11@3fb3c3a8 resid=10.
kernel: target0:0:0: asynchronous.
kernel: sym0: unexpected disconnect
target0:0:0: Write Buffer failure 700ff
target0:0:0: Domain Validation detected failure, dropping back
kernel: target0:0:0: asynchronous.
target0:0:0: Ending Domain Validation
kernel: sym1: <1010-33> rev 0x1 at pci 0000:01:07.1 irq 11
kernel: sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checkingkernel:
sym1:
open drain IRQ line driver, using on-chip SRAM
kernel: sym1: using LOAD/STORE-based firmware.
kernel: sym1: handling phase mismatch from SCRIPTS.
kernel: sym1: SCSI BUS has been reset.
kernel: scsi1 : sym-2.2.1
kernel: libata version 1.11 loaded.
The kernel config has:
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
reply other threads:[~2005-08-20 19:04 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43077EBB.5060705@adelphia.net \
--to=mikpolniak@adelphia.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox