From: Chris Boot <bootc@bootc.net>
To: Linux Kernel <linux-kernel@vger.kernel.org>
Subject: 2.6.15-rc5-mm1 sata_sil regression
Date: Wed, 07 Dec 2005 11:46:01 +0000 [thread overview]
Message-ID: <4396CB79.5040408@bootc.net> (raw)
Hi all,
I just upgraded to 2.6.15-rc5-mm1 from 2.6.15-rc2-mm1 and sata_sil
refused to recognise the two SATA drives that are connected to it:
[4294671.418000] libata version 1.20 loaded.
[4294671.419000] sata_sil 0000:00:0a.0: version 0.9
[4294671.419000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level,
low) -> IRQ 169
[4294671.429000] ata1: SATA max UDMA/100 cmd 0xF8802080 ctl 0xF880208A
bmdma 0xF8802010 irq 169
[4294671.440000] ata2: SATA max UDMA/100 cmd 0xF88020C0 ctl 0xF88020CA
bmdma 0xF8802018 irq 169
[4294671.652000] ata1: SATA link up 1.5 Gbps (SStatus 113)
[4294671.809000] ata1: dev 0 cfg 49:0000 82:0000 83:0000 84:0000 85:0000
86:0000 87:0000 88:0000
[4294671.809000] ata1: no dma
[4294671.809000] ata1: dev 0 not supported, ignoring
[4294671.815000] scsi0 : sata_sil
[4294671.839000] input: AT Translated Set 2 keyboard as /class/input/input0
[4294671.850000] atkbd.c: Spurious ACK on isa0060/serio0. Some program,
like XFree86, might be trying access hardware directly.
[4294672.021000] ata2: SATA link up 1.5 Gbps (SStatus 113)
[4294672.069000] input: AT Translated Set 2 keyboard as /class/input/input1
[4294672.178000] ata2: dev 0 cfg 49:0000 82:0000 83:0000 84:0000 85:0000
86:0000 87:0000 88:0000
[4294672.178000] ata2: no dma
[4294672.178000] ata2: dev 0 not supported, ignoring
[4294672.184000] scsi1 : sata_sil
My sata_via controller, also with 2 identical drives on it, works fine:
[4294672.731000] scsi2 : sata_via
[4294672.971000] ata4: SATA link up 1.5 Gbps (SStatus 113)
[4294673.163000] ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469
86:3c01 87:4023 88:407f
[4294673.163000] ata4: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48
[4294673.207000] ata4: dev 0 configured for UDMA/133
[4294673.248000] scsi3 : sata_via
[4294673.288000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294673.332000] Type: Direct-Access ANSI SCSI
revision: 05
[4294673.377000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294673.422000] Type: Direct-Access ANSI SCSI
revision: 05
[4294673.467000] SCSI device sda: 488397168 512-byte hdwr sectors
(250059 MB)
[4294673.512000] SCSI device sda: drive cache: write back
[4294673.554000] SCSI device sda: 488397168 512-byte hdwr sectors
(250059 MB)
[4294673.599000] SCSI device sda: drive cache: write back
[4294673.642000] sda: sda1 sda2 sda3
[4294673.704000] sd 2:0:0:0: Attached scsi disk sda
[4294673.746000] SCSI device sdb: 488397168 512-byte hdwr sectors
(250059 MB)
[4294673.791000] SCSI device sdb: drive cache: write back
[4294673.834000] SCSI device sdb: 488397168 512-byte hdwr sectors
(250059 MB)
[4294673.878000] SCSI device sdb: drive cache: write back
[4294673.920000] sdb: sdb1 sdb2 sdb3
[4294673.979000] sd 3:0:0:0: Attached scsi disk sdb
[4294674.021000] sd 2:0:0:0: Attached scsi generic sg0 type 0
[4294674.063000] sd 3:0:0:0: Attached scsi generic sg1 type 0
The controller is:
00:0a.0 Mass storage controller: Silicon Image, Inc. SiI 3112
[SATALink/SATARaid] Serial ATA Controller (rev 02) (prog-if 01)
Subsystem: Adaptec SATAConnect 1205SA Host Controller
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 169
I/O ports at a400 [size=8]
I/O ports at a800 [size=4]
I/O ports at ac00 [size=8]
I/O ports at b000 [size=4]
I/O ports at b400 [size=16]
Memory at ea001000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 50000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
00: 95 10 12 31 07 00 b0 02 02 01 80 01 08 20 00 00
10: 01 a4 00 00 01 a8 00 00 01 ac 00 00 01 b0 00 00
20: 01 b4 00 00 00 10 00 ea 00 00 00 00 05 90 50 02
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00
This all used to work fine in 2.6.15-rc2-mm1. Any ideas? Need any more
information?
Cheers,
Chris
--
Chris Boot
bootc@bootc.net
http://www.bootc.net/
next reply other threads:[~2005-12-07 11:46 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-07 11:46 Chris Boot [this message]
2005-12-07 12:48 ` 2.6.15-rc5-mm1 sata_sil regression Tejun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4396CB79.5040408@bootc.net \
--to=bootc@bootc.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox