From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1750891AbVLGLqF (ORCPT ); Wed, 7 Dec 2005 06:46:05 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1750899AbVLGLqF (ORCPT ); Wed, 7 Dec 2005 06:46:05 -0500 Received: from baldrick.bootc.net ([83.142.228.48]:56528 "EHLO baldrick.bootc.net") by vger.kernel.org with ESMTP id S1750891AbVLGLqE (ORCPT ); Wed, 7 Dec 2005 06:46:04 -0500 Message-ID: <4396CB79.5040408@bootc.net> Date: Wed, 07 Dec 2005 11:46:01 +0000 From: Chris Boot User-Agent: Mail/News 1.5 (X11/20051130) MIME-Version: 1.0 To: Linux Kernel Subject: 2.6.15-rc5-mm1 sata_sil regression Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Hi all, I just upgraded to 2.6.15-rc5-mm1 from 2.6.15-rc2-mm1 and sata_sil refused to recognise the two SATA drives that are connected to it: [4294671.418000] libata version 1.20 loaded. [4294671.419000] sata_sil 0000:00:0a.0: version 0.9 [4294671.419000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 169 [4294671.429000] ata1: SATA max UDMA/100 cmd 0xF8802080 ctl 0xF880208A bmdma 0xF8802010 irq 169 [4294671.440000] ata2: SATA max UDMA/100 cmd 0xF88020C0 ctl 0xF88020CA bmdma 0xF8802018 irq 169 [4294671.652000] ata1: SATA link up 1.5 Gbps (SStatus 113) [4294671.809000] ata1: dev 0 cfg 49:0000 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0000 [4294671.809000] ata1: no dma [4294671.809000] ata1: dev 0 not supported, ignoring [4294671.815000] scsi0 : sata_sil [4294671.839000] input: AT Translated Set 2 keyboard as /class/input/input0 [4294671.850000] atkbd.c: Spurious ACK on isa0060/serio0. Some program, like XFree86, might be trying access hardware directly. [4294672.021000] ata2: SATA link up 1.5 Gbps (SStatus 113) [4294672.069000] input: AT Translated Set 2 keyboard as /class/input/input1 [4294672.178000] ata2: dev 0 cfg 49:0000 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0000 [4294672.178000] ata2: no dma [4294672.178000] ata2: dev 0 not supported, ignoring [4294672.184000] scsi1 : sata_sil My sata_via controller, also with 2 identical drives on it, works fine: [4294672.731000] scsi2 : sata_via [4294672.971000] ata4: SATA link up 1.5 Gbps (SStatus 113) [4294673.163000] ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f [4294673.163000] ata4: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48 [4294673.207000] ata4: dev 0 configured for UDMA/133 [4294673.248000] scsi3 : sata_via [4294673.288000] Vendor: ATA Model: ST3250823AS Rev: 3.03 [4294673.332000] Type: Direct-Access ANSI SCSI revision: 05 [4294673.377000] Vendor: ATA Model: ST3250823AS Rev: 3.03 [4294673.422000] Type: Direct-Access ANSI SCSI revision: 05 [4294673.467000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [4294673.512000] SCSI device sda: drive cache: write back [4294673.554000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [4294673.599000] SCSI device sda: drive cache: write back [4294673.642000] sda: sda1 sda2 sda3 [4294673.704000] sd 2:0:0:0: Attached scsi disk sda [4294673.746000] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [4294673.791000] SCSI device sdb: drive cache: write back [4294673.834000] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [4294673.878000] SCSI device sdb: drive cache: write back [4294673.920000] sdb: sdb1 sdb2 sdb3 [4294673.979000] sd 3:0:0:0: Attached scsi disk sdb [4294674.021000] sd 2:0:0:0: Attached scsi generic sg0 type 0 [4294674.063000] sd 3:0:0:0: Attached scsi generic sg1 type 0 The controller is: 00:0a.0 Mass storage controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02) (prog-if 01) Subsystem: Adaptec SATAConnect 1205SA Host Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 169 I/O ports at a400 [size=8] I/O ports at a800 [size=4] I/O ports at ac00 [size=8] I/O ports at b000 [size=4] I/O ports at b400 [size=16] Memory at ea001000 (32-bit, non-prefetchable) [size=512] [virtual] Expansion ROM at 50000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 00: 95 10 12 31 07 00 b0 02 02 01 80 01 08 20 00 00 10: 01 a4 00 00 01 a8 00 00 01 ac 00 00 01 b0 00 00 20: 01 b4 00 00 00 10 00 ea 00 00 00 00 05 90 50 02 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00 This all used to work fine in 2.6.15-rc2-mm1. Any ideas? Need any more information? Cheers, Chris -- Chris Boot bootc@bootc.net http://www.bootc.net/