From: Giacomo Catenazzi <cate@cateee.net>
To: linux-kernel@vger.kernel.org
Subject: ppc kernel bugs in2.6.15-rc5: kobject_register failed for usbcore (-17)
Date: Wed, 07 Dec 2005 18:42:00 +0100 [thread overview]
Message-ID: <43971EE8.1080204@cateee.net> (raw)
I have some call trace in 2.6.15-rc5 (I don't know if
it happens also on old kernel, new machine, my first non x86 kernel)
Uniform CD-ROM driver Revision: 3.20
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Apple UniNorth 2 chipset
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e1026044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40]
MMIO=[f5000000-f50007ff] Max Packet=[2048]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e1026044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001124fffed13718]
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Adding 1269520k swap on /dev/hda3. Priority:-1 extents:1 across:1269520k
EXT3 FS on hda4, internal journal
SCSI subsystem initialized
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
kobject_register failed for ohci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c016eb50] bus_add_driver+0x80/0x180
[c016f978] driver_register+0x48/0x60
[c010cda4] __pci_register_driver+0x84/0xe0
[e20dd044] ohci_hcd_pci_init+0x44/0xd0 [ohci_hcd]
[c0046b38] sys_init_module+0x158/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for usbcore (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
kobject_register failed for ehci_hcd (-17)
Call trace:
[c01023ac] kobject_register+0x6c/0x90
[c0047d9c] sys_init_module+0x13bc/0x1530
[c00047fc] ret_from_syscall+0x0/0x44
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
[The hdc error was reported also on the original debian kernel, I should
still check]
ciao
cate
reply other threads:[~2005-12-07 17:43 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43971EE8.1080204@cateee.net \
--to=cate@cateee.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox