From: David Kredba <kredba@math.cas.cz>
To: linux-kernel@vger.kernel.org
Subject: Genius VideoWonder DVB-T PCI support
Date: Sat, 04 Mar 2006 09:31:39 +0100 [thread overview]
Message-ID: <4409506B.1050504@math.cas.cz> (raw)
Hello.
I got PCI card Genius VideoWonder DVB-T and I am trying to get it to work.
The card is using SAA7134H, TDA 10046HT and TDA 8274 chips.
My system is Gentoo (Base System version 1.6.14), kernel 2.6.15.
The card is, by lspci, visible as :
02:03.0 Multimedia controller: Philips Semiconductors SAA7134 Video
Broadcast Decoder (rev 01)
Subsystem: KYE Systems Corporation Unknown device 0301
Flags: bus master, medium devsel, latency 32, IRQ 19
Memory at ffdffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
If I tried to load saa7134-dvb module it loads and loads all of the
other needed modules, but it ignores the card and the module saa7134
reports the card as V4L2 device and not the DVB.
There is /usr/lib/hotplug/firmware dvb-fe-tda10046.fw firmware.
The state before saa7134-dvb loaded :
Module Size Used by
w83627hf 24080 0
hwmon_vid 2432 1 w83627hf
i2c_isa 3840 1 w83627hf
snd_seq_midi 7072 0
snd_emu10k1_synth 7040 0
snd_emux_synth 35456 1 snd_emu10k1_synth
snd_seq_virmidi 6272 1 snd_emux_synth
snd_seq_midi_emul 7040 1 snd_emux_synth
snd_pcm_oss 48800 0
snd_mixer_oss 17280 1 snd_pcm_oss
snd_seq_oss 33152 0
snd_seq_midi_event 6144 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss
snd_seq 50448 8
snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event
hci_usb 14100 5
emu10k1_gp 3072 0
snd_emu10k1 116388 2 snd_emu10k1_synth
snd_rawmidi 20896 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_seq_device 7308 7
snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi
snd_ac97_codec 91040 1 snd_emu10k1
snd_pcm 80772 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_timer 21636 3 snd_seq,snd_emu10k1,snd_pcm
snd_ac97_bus 2176 1 snd_ac97_codec
snd_page_alloc 8584 2 snd_emu10k1,snd_pcm
snd_util_mem 3584 2 snd_emux_synth,snd_emu10k1
snd_hwdep 7456 2 snd_emux_synth,snd_emu10k1
snd 48356 15
snd_emux_synth,snd_seq_virmidi,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep
soundcore 8032 1 snd
video_buf 17284 0
ir_kbd_i2c 6924 0
ir_common 8324 1 ir_kbd_i2c
videodev 7680 0
i2c_i801 8076 0
i2c_core 17536 4 w83627hf,i2c_isa,ir_kbd_i2c,i2c_i801
intel_agp 20380 1
agpgart 28880 1 intel_agp
r8169 23816 0
The state after the saa7134-dvb loaded :
saa7134_dvb 10500 0
mt352 6276 1 saa7134_dvb
saa7134 108896 1 saa7134_dvb
v4l2_common 4992 1 saa7134
v4l1_compat 13700 1 saa7134
video_buf_dvb 4868 1 saa7134_dvb
dvb_core 76584 1 video_buf_dvb
nxt200x 14724 1 saa7134_dvb
dvb_pll 9092 2 saa7134_dvb,nxt200x
tda1004x 15108 1 saa7134_dvb
firmware_class 8320 3 saa7134_dvb,nxt200x,tda1004x
w83627hf 24080 0
hwmon_vid 2432 1 w83627hf
i2c_isa 3840 1 w83627hf
snd_seq_midi 7072 0
snd_emu10k1_synth 7040 0
snd_emux_synth 35456 1 snd_emu10k1_synth
snd_seq_virmidi 6272 1 snd_emux_synth
snd_seq_midi_emul 7040 1 snd_emux_synth
snd_pcm_oss 48800 0
snd_mixer_oss 17280 1 snd_pcm_oss
snd_seq_oss 33152 0
snd_seq_midi_event 6144 3 snd_seq_midi,snd_seq_virmidi,snd_seq_oss
snd_seq 50448 8
snd_seq_midi,snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event
hci_usb 14100 5
emu10k1_gp 3072 0
snd_emu10k1 116388 2 snd_emu10k1_synth
snd_rawmidi 20896 3 snd_seq_midi,snd_seq_virmidi,snd_emu10k1
snd_seq_device 7308 7
snd_seq_midi,snd_emu10k1_synth,snd_emux_synth,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi
snd_ac97_codec 91040 1 snd_emu10k1
snd_pcm 80772 3 snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_timer 21636 3 snd_seq,snd_emu10k1,snd_pcm
snd_ac97_bus 2176 1 snd_ac97_codec
snd_page_alloc 8584 2 snd_emu10k1,snd_pcm
snd_util_mem 3584 2 snd_emux_synth,snd_emu10k1
snd_hwdep 7456 2 snd_emux_synth,snd_emu10k1
snd 48356 15
snd_emux_synth,snd_seq_virmidi,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer,snd_hwdep
soundcore 8032 1 snd
video_buf 17284 3 saa7134_dvb,saa7134,video_buf_dvb
ir_kbd_i2c 6924 1 saa7134
ir_common 8324 2 saa7134,ir_kbd_i2c
videodev 7680 1 saa7134
i2c_i801 8076 0
i2c_core 17536 9
saa7134_dvb,mt352,saa7134,nxt200x,tda1004x,w83627hf,i2c_isa,ir_kbd_i2c,i2c_i801
intel_agp 20380 1
agpgart 28880 1 intel_agp
r8169 23816 0
There is this and only this message, coming from saa7134, in teh
/var/log/messages file :
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
saa7134[0]: found at 0000:02:03.0, rev: 1, irq: 19, latency: 32, mmio:
0xffdffc00
saa7134[0]: subsystem: 1489:0301, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7134[0]: board init: gpio is 10000
saa7134[0]: i2c eeprom 00: 89 14 01 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 01 03 08 ff 01 ec ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff 1b 00 c0 ff 10 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
There is no support for that card at linuxtv.org site.
Is there possibility to get the card working?
Thank you very much, David Kredba
next reply other threads:[~2006-03-04 8:31 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-03-04 8:31 David Kredba [this message]
2006-03-09 10:06 ` Genius VideoWonder DVB-T PCI support Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4409506B.1050504@math.cas.cz \
--to=kredba@math.cas.cz \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox