From: Johny <kernel@agotnes.com>
To: kernel list <linux-kernel@vger.kernel.org>, linux-usb@vger.kernel.org
Cc: "Johny Ågotnes" <kernel@agotnes.com>
Subject: Re: 2.6.17-rc5-mm3 - USB issues
Date: Mon, 12 Jun 2006 17:29:32 +1000 [thread overview]
Message-ID: <448D17DC.5000400@agotnes.com> (raw)
In-Reply-To: <448B7A88.5070009@agotnes.com>
[-- Attachment #1: Type: text/plain, Size: 5761 bytes --]
Further to this, I tested with 2.6.17-rc6-mm2 today, no changes. I've
attached as .txt files the following;
lsusb output for both a 2.6.16 kernel and the 2.6.17-rc6-mm2 kernel
/proc/bus/usb/devices output, again for the same kernels.
Noting that there are a lot less devices in the -mm kernel due to the
error below.
Again, any further debugging I can provide, just let me know!
:)J
Please advise
Johny Ågotnes wrote:
> All,
>
> My USB hub isn't recognised with the latest -mm series, whereas with
> 2.6.16 vanilla it is picked up & used immediately.
>
> The error I get in dmesg is;
>
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> usb 1-4: new high speed USB device using ehci_hcd and address 3
> ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably
> using the wrong IRQ.
> usb 1-4: device not accepting address 3, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 4
> usb 1-4: device not accepting address 4, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 5
> usb 1-4: device not accepting address 5, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 6
> usb 1-4: device not accepting address 6, error -110
> usb 2-2: new full speed USB device using uhci_hcd and address 2
>
> Which seems to be related to my Belkin hub. The full USB related dmesg
> information can be found below, I'm happy to provide further debugging
> information as required :)
>
> ACPI (acpi_bus-0192): Device `USB9]is not power manageable [20060310]
> ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
> PCI: setting IRQ 10 as level-triggered
> ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level,
> low) -> IRQ 10
> ehci_hcd 0000:00:10.3: EHCI Host Controller
> ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:10.3: irq 10, io mem 0xea022000
> ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: new device found, idVendor=0000, idProduct=0000
> usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: EHCI Host Controller
> usb usb1: Manufacturer: Linux 2.6.17-rc5-mm3 ehci_hcd
> usb usb1: SerialNumber: 0000:00:10.3
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 6 ports detected
> USB Universal Host Controller Interface driver v3.0
> ACPI (acpi_bus-0192): Device `USB6]is not power manageable [20060310]
> ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level,
> low) -> IRQ 11
> uhci_hcd 0000:00:10.0: UHCI Host Controller
> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d000
> usb usb2: new device found, idVendor=0000, idProduct=0000
> usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: UHCI Host Controller
> usb usb2: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
> usb usb2: SerialNumber: 0000:00:10.0
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI (acpi_bus-0192): Device `USB7]is not power manageable [20060310]
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
> ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 11 (level,
> low) -> IRQ 11
> uhci_hcd 0000:00:10.1: UHCI Host Controller
> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:10.1: irq 11, io base 0x0000d400
> usb usb3: new device found, idVendor=0000, idProduct=0000
> usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb3: Product: UHCI Host Controller
> usb usb3: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
> usb usb3: SerialNumber: 0000:00:10.1
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI (acpi_bus-0192): Device `USB8]is not power manageable [20060310]
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level,
> low) -> IRQ 10
> uhci_hcd 0000:00:10.2: UHCI Host Controller
> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d800
> usb usb4: new device found, idVendor=0000, idProduct=0000
> usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb4: Product: UHCI Host Controller
> usb usb4: Manufacturer: Linux 2.6.17-rc5-mm3 uhci_hcd
> usb usb4: SerialNumber: 0000:00:10.2
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> usb 1-4: new high speed USB device using ehci_hcd and address 3
> ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably
> using the wrong IRQ.
> usb 1-4: device not accepting address 3, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 4
> usb 1-4: device not accepting address 4, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 5
> usb 1-4: device not accepting address 5, error -110
> usb 1-4: new high speed USB device using ehci_hcd and address 6
> usb 1-4: device not accepting address 6, error -110
> usb 2-2: new full speed USB device using uhci_hcd and address 2
> usb 2-2: new device found, idVendor=0731, idProduct=0528
> usb 2-2: new device strings: Mfr=0, Product=0, SerialNumber=0
> usb 2-2: configuration #1 chosen from 1 choice
> usbcore: registered new driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>
[-- Attachment #2: usb-dev-16.txt --]
[-- Type: text/plain, Size: 6598 bytes --]
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.16-gentoo-r7 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0731 ProdID=0528 Rev= 0.01
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.16-gentoo-r7 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=6017 ProdID=2230 Rev=c5.bd
S: Manufacturer=Sunplus Technology Inc.
S: Product=USB to Serial-ATA bridge
S: SerialNumber=External D000FFFF_00000000_0_A
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=480 MxCh= 7
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=050d ProdID=0237 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 2mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I: If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=04 Port=01 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=05a9 ProdID=4519 Rev= 1.00
S: Manufacturer=OmniVision Technologies, Inc.
S: Product=USB Camera
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=01(Isoc) MxPS= 384 Ivl=1ms
I: If#= 0 Alt= 2 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=01(Isoc) MxPS= 512 Ivl=1ms
I: If#= 0 Alt= 3 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=01(Isoc) MxPS= 768 Ivl=1ms
I: If#= 0 Alt= 4 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=01(Isoc) MxPS= 896 Ivl=1ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
I: If#= 2 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
E: Ad=82(I) Atr=05(Isoc) MxPS= 40 Ivl=1ms
T: Bus=01 Lev=02 Prnt=04 Port=02 Cnt=02 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=13b1 ProdID=001d Rev= 1.40
S: Manufacturer=LINKSYS
S: Product=Linksys CIT200
S: SerialNumber=USBGAP00000000000000000000166124961
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
I: If#= 1 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
E: Ad=02(O) Atr=05(Isoc) MxPS= 64 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
I: If#= 2 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none)
E: Ad=81(I) Atr=05(Isoc) MxPS= 64 Ivl=1ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=255ms
T: Bus=01 Lev=02 Prnt=04 Port=05 Cnt=03 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 2.72
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
[-- Attachment #3: usb-dev-mm.txt --]
[-- Type: text/plain, Size: 2302 bytes --]
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.17-rc6-mm2 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0731 ProdID=0528 Rev= 0.01
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 10 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.17-rc6-mm2 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
[-- Attachment #4: lsusb-16.txt --]
[-- Type: text/plain, Size: 496 bytes --]
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0731:0528 Susteen, Inc. SonyEricsson DCU-11 Cable
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 007: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 001 Device 006: ID 13b1:001d Linksys
Bus 001 Device 005: ID 05a9:4519 OmniVision Technologies, Inc.
Bus 001 Device 004: ID 050d:0237 Belkin Components
Bus 001 Device 003: ID 6017:2230
Bus 001 Device 001: ID 0000:0000
[-- Attachment #5: lsusb-mm.txt --]
[-- Type: text/plain, Size: 213 bytes --]
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 0731:0528 Susteen, Inc. SonyEricsson DCU-11 Cable
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
next prev parent reply other threads:[~2006-06-12 7:30 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-06-11 2:06 2.6.17-rc5-mm3 - USB issues Johny Ågotnes
2006-06-12 7:29 ` Johny [this message]
[not found] <mailman.1149991921.17505.linux-kernel2news@redhat.com>
2006-06-20 9:15 ` Pete Zaitcev
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=448D17DC.5000400@agotnes.com \
--to=kernel@agotnes.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox