2.6.20-rc7 mtrr handling

Sebastian Kemper
2007-01-31T19:46:53Z

Hello list,

I read about the changes regarding the mtrr code in the upcoming 2.6.20
kernel and so today I tried rc7.

Since quite some time I had warning messages like

mtrr... overlaps existing...

whenever I started up Xorg with DRI enabled. This doesn't happen anymore
with 2.6.20-rc7.

But now /proc/mtrr shows 256MB of video ram, same as lspci, whereas the
real amount of video ram (as properly detected by X) is only 128MB.

I have a Radeon 9250 from Connect3d with AGP, DVI, VGA, TV-Out and
128bit memory bus width.

I'm wondering if this misdetection could become an issue.

cat /proc/mtrr
reg00: base=0x00000000 ( 0MB), size= 512MB: write-back, count=1
reg01: base=0xe0000000 (3584MB), size= 128MB: write-combining, count=2
reg02: base=0xd0000000 (3328MB), size= 256MB: write-combining, count=3

The lines are RAM, AGP Aperture Size and video ram.

grep -i videoram /var/log/Xorg.0.log
(--) RADEON(0): Mapped VideoRAM: 131072 kByte (128 bit DDR SDRAM)

lspci -vvv
...
02:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon
9200 PRO] (rev 01) (prog-if 00 [VGA])
Subsystem: Connect Components Ltd Unknown device 2801
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at e9000000 (32-bit, non-prefetchable)
[size=64K]
[virtual] Expansion ROM at e8000000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit-
FW- Rate=x8
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

dmesg shows:

...
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz,
System=166.00 MHz
radeonfb: PLL min 20000 max 40000
radeonfb: Monitor 1 type DFP found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Dynamic Clock Power Management enabled
Console: switching to colour frame buffer device 160x64
radeonfb (0000:02:00.0): ATI Radeon Y`
...
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
[drm] Loading R200 Microcode

/usr/src/linux/scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux section_eight 2.6.20-rc7 #2 Wed Jan 31 20:23:30 CET 2007 i686 AMD
Sempron(tm) 2400+ AuthenticAMD GNU/Linux

Gnu C 4.1.1
Gnu make 3.81
binutils 2.16.1
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.2
e2fsprogs 1.39
Linux C Library > libc.2.4
Dynamic linker (ldd) 2.4
Procps 3.2.6
Net-tools 1.60
Kbd 1.12
Sh-utils 6.4
udev 103
Modules Loaded lirc_serial lirc_dev snd_ice1712
snd_ice17xx_ak4xxx snd_ak4xxx_adda snd_cs8427 snd_ac97_codec snd_pcm
snd_page_alloc ac97_bus snd_i2c snd_mpu401_uart snd_rawmidi dvb_ttpci
saa7146_vv video_buf saa7146 ttpci_eeprom stv0299 dvb_core

Regards
Sebastian