* 2.6.22-git17 boot failure
@ 2007-07-22 23:47 Tilman Schmidt
2007-07-23 0:31 ` Gabriel C
2007-07-23 0:52 ` Tilman Schmidt
0 siblings, 2 replies; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-22 23:47 UTC (permalink / raw)
To: LKML
[-- Attachment #1: Type: text/plain, Size: 455 bytes --]
On my test machine with a Pentium D 940 processor, Intel DQ965GF
mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
to come up because it cannot find the disk drives. Same issue
with a clone of the 'linus' git tree. Anything known?
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* RE: 2.6.22-git17 boot failure
@ 2007-07-23 0:27 Sid Boyce
0 siblings, 0 replies; 27+ messages in thread
From: Sid Boyce @ 2007-07-23 0:27 UTC (permalink / raw)
To: linux-kernel
Tilman Schmidt: wrote
> On my test machine with a Pentium D 940 processor, Intel DQ965GF
> mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
> to come up because it cannot find the disk drives. Same issue
> with a clone of the 'linus' git tree. Anything known?
I don't know if this is any indication.
I have no SATA drives, but I noticed booting 2.6.22-git16 x86_64 I got
error messages with "sata slow in responding" also "EH timeout" and my
IDE drive /dev/sda1 giving ext3 errors, ending in a filesystem not
clean prompt. Did fsck.ext3 using openSUSE 10.3Alpha3 DVD, that fixed a
string of wrong inode errors. Booted an earlier kernel and turned off
loading the sata_nv module, then 2.6.22-git16 and later 2.6.22-git17
booted without problems, so I put it down to a motherboard problem with
the SATA.
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-22 23:47 Tilman Schmidt
@ 2007-07-23 0:31 ` Gabriel C
2007-07-23 0:52 ` Tilman Schmidt
1 sibling, 0 replies; 27+ messages in thread
From: Gabriel C @ 2007-07-23 0:31 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML
Tilman Schmidt wrote:
> On my test machine with a Pentium D 940 processor, Intel DQ965GF
> mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
> to come up because it cannot find the disk drives. Same issue
> with a clone of the 'linus' git tree. Anything known?
>
Could you post the config ?
Regards,
Gabriel C
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-22 23:47 Tilman Schmidt
2007-07-23 0:31 ` Gabriel C
@ 2007-07-23 0:52 ` Tilman Schmidt
2007-07-23 8:51 ` Jeremy Fitzhardinge
2007-07-23 9:25 ` Andi Kleen
1 sibling, 2 replies; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-23 0:52 UTC (permalink / raw)
To: LKML; +Cc: g3vbv, nix.or.die
[-- Attachment #1: Type: text/plain, Size: 706 bytes --]
on Mon, 23 Jul 2007 01:47:30 +0200, /me wrote:
> On my test machine with a Pentium D 940 processor, Intel DQ965GF
> mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
> to come up because it cannot find the disk drives. Same issue
> with a clone of the 'linus' git tree. Anything known?
Ok, scrap this. Turns out it wasn't a good idea to answer 'Y' to
the new XEN config option during "make oldconfig". After changing
it to CONFIG_XEN=n, all's well again. Sorry for the noise.
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 0:52 ` Tilman Schmidt
@ 2007-07-23 8:51 ` Jeremy Fitzhardinge
2007-07-23 10:25 ` Tilman Schmidt
2007-07-23 9:25 ` Andi Kleen
1 sibling, 1 reply; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-23 8:51 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, g3vbv, nix.or.die
Tilman Schmidt wrote:
> on Mon, 23 Jul 2007 01:47:30 +0200, /me wrote:
>
>> On my test machine with a Pentium D 940 processor, Intel DQ965GF
>> mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
>> to come up because it cannot find the disk drives. Same issue
>> with a clone of the 'linus' git tree. Anything known?
>>
>
> Ok, scrap this. Turns out it wasn't a good idea to answer 'Y' to
> the new XEN config option during "make oldconfig". After changing
> it to CONFIG_XEN=n, all's well again. Sorry for the noise.
>
That seems very unlikely. If you're booting a Xen-enabled kernel on
bare hardware, the Xen code should have no effect at all. It certainly
shouldn't prevent you from probing devices.
Could you send me your .config and dmesg output? Are you saying that
leaving PARAVIRT enabled but XEN disabled will allow your system to
boot? What happens if you enable VMI and/or LGUEST?
Thanks,
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 0:52 ` Tilman Schmidt
2007-07-23 8:51 ` Jeremy Fitzhardinge
@ 2007-07-23 9:25 ` Andi Kleen
1 sibling, 0 replies; 27+ messages in thread
From: Andi Kleen @ 2007-07-23 9:25 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, g3vbv, nix.or.die, jeremy
Tilman Schmidt <tilman@imap.cc> writes:
> on Mon, 23 Jul 2007 01:47:30 +0200, /me wrote:
> > On my test machine with a Pentium D 940 processor, Intel DQ965GF
> > mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
> > to come up because it cannot find the disk drives. Same issue
> > with a clone of the 'linus' git tree. Anything known?
>
> Ok, scrap this. Turns out it wasn't a good idea to answer 'Y' to
> the new XEN config option during "make oldconfig". After changing
> it to CONFIG_XEN=n, all's well again. Sorry for the noise.
Well, xen should not break the boot on a native system, assuming
the configuration without xen is correct. If it does there is a bug
somewhere that needs to be fixed. Can you verify it by reenabling xen on the
working configuration without changing anything else?
-Andi
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 8:51 ` Jeremy Fitzhardinge
@ 2007-07-23 10:25 ` Tilman Schmidt
2007-07-23 14:51 ` Jeremy Fitzhardinge
0 siblings, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-23 10:25 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: LKML, andi, nix.or.die
[-- Attachment #1.1: Type: text/plain, Size: 2404 bytes --]
Jeremy Fitzhardinge schrieb:
> Tilman Schmidt wrote:
>>
>>> On my test machine with a Pentium D 940 processor, Intel DQ965GF
>>> mainboard and SATA disks, kernel 2.6.22-git17 (32 bit build) fails
>>> to come up because it cannot find the disk drives. Same issue
>>> with a clone of the 'linus' git tree. [...]
>> Turns out it wasn't a good idea to answer 'Y' to
>> the new XEN config option during "make oldconfig". After changing
>> it to CONFIG_XEN=n, all's well again. Sorry for the noise.
>
> That seems very unlikely. If you're booting a Xen-enabled kernel on
> bare hardware, the Xen code should have no effect at all. It certainly
> shouldn't prevent you from probing devices.
>
> Could you send me your .config and dmesg output?
Attached are .config and dmesg (as captured in SuSE's /var/log/boot.msg)
of a CONFIG_XEN=n git-current build. The .config diff of the previous
kernel (which didn't detect the SATA disks) and this one is:
ts@xenon:~/kernel/linux-2.6> diff .config.old .config
4c4
< # Mon Jul 23 01:51:16 2007
---
> # Mon Jul 23 02:06:38 2007
129c129
< CONFIG_XEN=y
---
> # CONFIG_XEN is not set
762d761
< CONFIG_XEN_BLKDEV_FRONTEND=m
1105d1103
< CONFIG_XEN_NETDEV_FRONTEND=m
1377d1374
< CONFIG_HVC_XEN=y
ts@xenon:~/kernel/linux-2.6>
The .config I used for the -git17 kernel differs from the attached one
in two respects:
- It has CONFIG_MPENTIUM4=y instead of CONFIG_MCORE2=y following
the answers to my recent question about Pentium D.
- It has CONFIG_IDE=m and most of the actual IDE drivers compiled
as modules even though they are not used on that system. I
disabled these for the git-current test because I suspected they
might be the cause of the problem, but that didn't change anything.
The working/nonworking diff is the same as above.
> Are you saying that
> leaving PARAVIRT enabled but XEN disabled will allow your system to
> boot?
Exactly.
> What happens if you enable VMI and/or LGUEST?
As you can see in the attached .config, both are enabled already,
without doing any harm.
Thanks,
Tilman
PS: I see that 2.6.23-rc1 is out. I'll try to reproduce the behaviour
with that this evening.
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #1.2: working.config --]
[-- Type: text/plain, Size: 57927 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.22
# Mon Jul 23 02:06:38 2007
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION="-git"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
# CONFIG_TASK_XACCT is not set
# CONFIG_USER_NS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_CPUSETS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBD=y
CONFIG_BLK_DEV_IO_TRACE=y
CONFIG_LSF=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
CONFIG_DEFAULT_DEADLINE=y
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="deadline"
#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
CONFIG_PARAVIRT=y
# CONFIG_XEN is not set
CONFIG_VMI=y
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MCORE2=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_XADD=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_NR_CPUS=8
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
CONFIG_MICROCODE=m
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
CONFIG_HIGHPTE=y
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_IRQBALANCE=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
# CONFIG_COMPAT_VDSO is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SUSPEND_SMP=y
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_SLEEP_PROC_SLEEP is not set
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=m
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
# CONFIG_ACPI_SBS is not set
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
CONFIG_APM_DO_ENABLE=y
# CONFIG_APM_CPU_IDLE is not set
CONFIG_APM_DISPLAY_BLANK=y
CONFIG_APM_ALLOW_INTS=y
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_POWERNOW_K6=m
CONFIG_X86_POWERNOW_K7=m
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_GX_SUSPMOD=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_SMI=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_CPUFREQ_NFORCE2=m
CONFIG_X86_LONGRUN=m
CONFIG_X86_LONGHAUL=m
CONFIG_X86_E_POWERSAVER=m
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK=y
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_K8_NB=y
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_XFRM_SUB_POLICY=y
CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=m
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m
CONFIG_TCP_CONG_YEAH=m
CONFIG_TCP_CONG_ILLINOIS=m
# CONFIG_DEFAULT_BIC is not set
# CONFIG_DEFAULT_CUBIC is not set
# CONFIG_DEFAULT_HTCP is not set
# CONFIG_DEFAULT_VEGAS is not set
# CONFIG_DEFAULT_WESTWOOD is not set
CONFIG_DEFAULT_RENO=y
CONFIG_DEFAULT_TCP_CONG="reno"
CONFIG_TCP_MD5SIG=y
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12
#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y
#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_IPV6_MIP6=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=m
CONFIG_IPV6_TUNNEL=m
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
CONFIG_NETLABEL=y
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_SECMARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_U32=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
CONFIG_NF_NAT_AMANDA=m
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_MH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m
#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y
#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
CONFIG_IP_DCCP_CCID2_DEBUG=y
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m
CONFIG_IP_DCCP_CCID3_DEBUG=y
CONFIG_IP_DCCP_CCID3_RTO=100
#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
# CONFIG_NET_DCCPPROBE is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=m
CONFIG_LLC2=m
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
CONFIG_X25=m
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y
#
# Wireless
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_AX88796=m
CONFIG_PARPORT_1284=y
CONFIG_PARPORT_NOT_PC=y
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=y
# CONFIG_PARIDE is not set
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=64000
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ASUS_LAPTOP is not set
# CONFIG_MSI_LAPTOP is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
CONFIG_SCSI_SAS_LIBSAS_DEBUG=y
#
# SCSI low-level drivers
#
CONFIG_ISCSI_TCP=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=5000
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC7XXX_OLD=m
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=15000
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
CONFIG_AIC79XX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC94XX=m
CONFIG_AIC94XX_DEBUG=y
CONFIG_SCSI_DPT_I2O=m
CONFIG_SCSI_ADVANSYS=m
CONFIG_SCSI_ARCMSR=m
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_HPTIOP=m
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
CONFIG_SCSI_DMX3191D=m
CONFIG_SCSI_EATA=m
CONFIG_SCSI_EATA_TAGGED_QUEUE=y
CONFIG_SCSI_EATA_LINKED_COMMANDS=y
CONFIG_SCSI_EATA_MAX_TAGS=16
CONFIG_SCSI_FUTURE_DOMAIN=m
CONFIG_SCSI_GDTH=m
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
CONFIG_SCSI_INIA100=m
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
CONFIG_SCSI_STEX=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
CONFIG_SCSI_IPR=m
CONFIG_SCSI_IPR_TRACE=y
CONFIG_SCSI_IPR_DUMP=y
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
CONFIG_SCSI_QLA_ISCSI=m
CONFIG_SCSI_LPFC=m
CONFIG_SCSI_DC395x=m
CONFIG_SCSI_DC390T=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m
# CONFIG_SCSI_SRP is not set
CONFIG_ATA=m
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
CONFIG_SATA_AHCI=m
CONFIG_SATA_SVW=m
CONFIG_ATA_PIIX=m
CONFIG_SATA_MV=m
CONFIG_SATA_NV=m
CONFIG_PDC_ADMA=m
CONFIG_SATA_QSTOR=m
CONFIG_SATA_PROMISE=m
CONFIG_SATA_SX4=m
CONFIG_SATA_SIL=m
CONFIG_SATA_SIL24=m
CONFIG_SATA_SIS=m
CONFIG_SATA_ULI=m
CONFIG_SATA_VIA=m
CONFIG_SATA_VITESSE=m
CONFIG_SATA_INIC162X=m
CONFIG_PATA_ALI=m
CONFIG_PATA_AMD=m
CONFIG_PATA_ARTOP=m
CONFIG_PATA_ATIIXP=m
CONFIG_PATA_CMD640_PCI=m
CONFIG_PATA_CMD64X=m
CONFIG_PATA_CS5520=m
CONFIG_PATA_CS5530=m
CONFIG_PATA_CS5535=m
CONFIG_PATA_CYPRESS=m
CONFIG_PATA_EFAR=m
# CONFIG_ATA_GENERIC is not set
CONFIG_PATA_HPT366=m
CONFIG_PATA_HPT37X=m
CONFIG_PATA_HPT3X2N=m
CONFIG_PATA_HPT3X3=m
# CONFIG_PATA_HPT3X3_DMA is not set
CONFIG_PATA_IT821X=m
CONFIG_PATA_IT8213=m
CONFIG_PATA_JMICRON=m
CONFIG_PATA_TRIFLEX=m
CONFIG_PATA_MARVELL=m
CONFIG_PATA_MPIIX=m
# CONFIG_PATA_OLDPIIX is not set
CONFIG_PATA_NETCELL=m
CONFIG_PATA_NS87410=m
CONFIG_PATA_OPTI=m
CONFIG_PATA_OPTIDMA=m
CONFIG_PATA_PDC_OLD=m
CONFIG_PATA_RADISYS=m
CONFIG_PATA_RZ1000=m
CONFIG_PATA_SC1200=m
CONFIG_PATA_SERVERWORKS=m
CONFIG_PATA_PDC2027X=m
CONFIG_PATA_SIL680=m
CONFIG_PATA_SIS=m
CONFIG_PATA_VIA=m
CONFIG_PATA_WINBOND=m
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
CONFIG_DM_MULTIPATH_RDAC=m
# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_SBP2=m
# CONFIG_IEEE1394 is not set
CONFIG_I2O=m
CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m
#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
CONFIG_ICPLUS_PHY=m
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
CONFIG_TULIP_NAPI=y
CONFIG_TULIP_NAPI_HW_MITIGATION=y
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_HP100=m
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
# CONFIG_PCNET32_NAPI is not set
CONFIG_AMD8111_ETH=m
# CONFIG_AMD8111E_NAPI is not set
CONFIG_ADAPTEC_STARFIRE=m
CONFIG_ADAPTEC_STARFIRE_NAPI=y
CONFIG_B44=m
CONFIG_FORCEDETH=m
# CONFIG_FORCEDETH_NAPI is not set
CONFIG_DGRS=m
CONFIG_EEPRO100=m
CONFIG_E100=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
# CONFIG_VIA_RHINE_MMIO is not set
CONFIG_VIA_RHINE_NAPI=y
CONFIG_SC92031=m
# CONFIG_NET_POCKET is not set
CONFIG_NETDEV_1000=y
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
CONFIG_R8169_NAPI=y
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=m
CONFIG_SKY2=m
# CONFIG_SKY2_DEBUG is not set
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=m
CONFIG_BNX2=m
CONFIG_QLA3XXX=m
CONFIG_ATL1=m
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOL2TP=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLHC=m
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
# CONFIG_NET_FC is not set
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_ISDN=m
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
CONFIG_ISDN_X25=y
#
# ISDN feature submodules
#
CONFIG_ISDN_DIVERSION=m
#
# ISDN4Linux hardware drivers
#
#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8
#
# HiSax supported cards
#
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
CONFIG_HISAX_DEBUG=y
#
# HiSax PCMCIA card service modules
#
#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
CONFIG_HISAX_HFCUSB=m
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y
#
# Active cards
#
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
CONFIG_GIGASET_M101=m
CONFIG_GIGASET_DEBUG=y
CONFIG_GIGASET_UNDOCREQ=y
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_CAPI_TRACE=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m
#
# CAPI hardware drivers
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
CONFIG_INPUT_POLLDEV=m
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_TSDEV=m
CONFIG_INPUT_TSDEV_SCREEN_X=240
CONFIG_INPUT_TSDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_SUNKBD=m
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_XTKBD=m
CONFIG_KEYBOARD_NEWTON=m
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_ANALOG=m
CONFIG_JOYSTICK_A3D=m
CONFIG_JOYSTICK_ADI=m
CONFIG_JOYSTICK_COBRA=m
CONFIG_JOYSTICK_GF2K=m
CONFIG_JOYSTICK_GRIP=m
CONFIG_JOYSTICK_GRIP_MP=m
CONFIG_JOYSTICK_GUILLEMOT=m
CONFIG_JOYSTICK_INTERACT=m
CONFIG_JOYSTICK_SIDEWINDER=m
CONFIG_JOYSTICK_TMDC=m
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
CONFIG_JOYSTICK_DB9=m
CONFIG_JOYSTICK_GAMECON=m
CONFIG_JOYSTICK_TURBOGRAFX=m
CONFIG_JOYSTICK_JOYDUMP=m
# CONFIG_JOYSTICK_XPAD is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
CONFIG_INPUT_WISTRON_BTNS=m
# CONFIG_INPUT_ATLAS_BTNS is not set
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=m
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PARKBD=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
CONFIG_HVC_DRIVER=y
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_PANIC_EVENT=y
CONFIG_IPMI_PANIC_STRING=y
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
CONFIG_HW_RANDOM_GEODE=m
CONFIG_HW_RANDOM_VIA=m
CONFIG_NVRAM=m
CONFIG_RTC=y
CONFIG_R3964=m
CONFIG_APPLICOM=m
CONFIG_SONYPI=m
CONFIG_AGP=m
CONFIG_AGP_ALI=m
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
CONFIG_AGP_AMD64=m
CONFIG_AGP_INTEL=m
CONFIG_AGP_NVIDIA=m
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
CONFIG_AGP_EFFICEON=m
CONFIG_DRM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_I915=m
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m
CONFIG_MWAVE=m
CONFIG_PC8736x_GPIO=m
CONFIG_NSC_GPIO=m
CONFIG_CS5535_GPIO=m
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=4096
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_TIS=m
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_TCG_INFINEON=m
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m
#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_OCORES=m
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_I2C_SIMTEC=m
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_TAOS_EVM=m
CONFIG_I2C_STUB=m
CONFIG_I2C_TINY_USB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
CONFIG_DS1682=m
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
CONFIG_SENSORS_TSL2550=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
CONFIG_SPI=y
CONFIG_SPI_DEBUG=y
CONFIG_SPI_MASTER=y
#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m
CONFIG_SPI_BUTTERFLY=m
CONFIG_SPI_LM70_LLP=m
#
# SPI Protocol Masters
#
CONFIG_SPI_AT25=m
CONFIG_SPI_SPIDEV=m
CONFIG_SPI_TLE62X0=m
CONFIG_W1=m
#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS2490=m
CONFIG_W1_MASTER_DS2482=m
#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2433=m
CONFIG_W1_SLAVE_DS2433_CRC=y
CONFIG_W1_SLAVE_DS2760=m
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
CONFIG_PDA_POWER=m
CONFIG_BATTERY_DS2760=m
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ABITUGURU=m
CONFIG_SENSORS_ABITUGURU3=m
CONFIG_SENSORS_AD7418=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1029=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_CORETEMP=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM70=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_LM93=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_MAX6650=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_PC87427=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_DME1737=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT1211=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
CONFIG_SENSORS_APPLESMC=m
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multifunction device drivers
#
CONFIG_MFD_SM501=m
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_BT848 is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_W9966 is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_CPIA2 is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_TUNER_TEA5761 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set
# CONFIG_VIDEO_IVTV is not set
# CONFIG_VIDEO_CAFE_CCIC is not set
CONFIG_V4L_USB_DRIVERS=y
# CONFIG_VIDEO_PVRUSB2 is not set
# CONFIG_VIDEO_EM28XX is not set
# CONFIG_VIDEO_USBVISION is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_QUICKCAM_MESSENGER is not set
# CONFIG_USB_ET61X251 is not set
# CONFIG_VIDEO_OVCAMCHIP is not set
# CONFIG_USB_W9968CF is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set
# CONFIG_USB_ZC0301 is not set
# CONFIG_USB_PWC is not set
# CONFIG_USB_ZR364XX is not set
CONFIG_RADIO_ADAPTERS=y
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
# CONFIG_USB_DSBR is not set
# CONFIG_DVB_CORE is not set
# CONFIG_DAB is not set
#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
# CONFIG_BACKLIGHT_PROGEAR is not set
#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=m
#
# Display hardware drivers
#
CONFIG_VGASTATE=m
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=m
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SYS_FILLRECT=m
CONFIG_FB_SYS_COPYAREA=m
CONFIG_FB_SYS_IMAGEBLIT=m
CONFIG_FB_SYS_FOPS=m
CONFIG_FB_DEFERRED_IO=y
CONFIG_FB_SVGALIB=m
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
#
# Frame buffer hardware drivers
#
CONFIG_FB_CIRRUS=m
CONFIG_FB_PM2=m
CONFIG_FB_PM2_FIFO_DISCONNECT=y
CONFIG_FB_CYBER2000=m
CONFIG_FB_ARC=m
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
# CONFIG_FB_HECUBA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
CONFIG_FB_RIVA=m
CONFIG_FB_RIVA_I2C=y
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_RIVA_BACKLIGHT=y
CONFIG_FB_I810=m
CONFIG_FB_I810_GTF=y
CONFIG_FB_I810_I2C=y
# CONFIG_FB_LE80578 is not set
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
CONFIG_FB_INTEL_I2C=y
CONFIG_FB_MATROX=y
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
CONFIG_FB_S3=m
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
CONFIG_FB_SAVAGE_ACCEL=y
CONFIG_FB_SIS=m
CONFIG_FB_SIS_300=y
CONFIG_FB_SIS_315=y
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
CONFIG_FB_3DFX=m
CONFIG_FB_3DFX_ACCEL=y
CONFIG_FB_VOODOO1=m
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_SM501 is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
CONFIG_SND_DYNAMIC_MINORS=y
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
# CONFIG_SND_DEBUG_DETECT is not set
# CONFIG_SND_PCM_XRUN_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
# CONFIG_SND_MTS64 is not set
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
# CONFIG_SND_PORTMAN2X4 is not set
CONFIG_SND_SB_COMMON=m
CONFIG_SND_SB16_DSP=m
#
# PCI devices
#
CONFIG_SND_AD1889=m
CONFIG_SND_ALS300=m
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
CONFIG_SND_CS5530=m
CONFIG_SND_CS5535AUDIO=m
CONFIG_SND_DARLA20=m
CONFIG_SND_GINA20=m
CONFIG_SND_LAYLA20=m
CONFIG_SND_DARLA24=m
CONFIG_SND_GINA24=m
CONFIG_SND_LAYLA24=m
CONFIG_SND_MONA=m
CONFIG_SND_MIA=m
CONFIG_SND_ECHO3G=m
CONFIG_SND_INDIGO=m
CONFIG_SND_INDIGOIO=m
CONFIG_SND_INDIGODJ=m
CONFIG_SND_EMU10K1=m
CONFIG_SND_EMU10K1X=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
CONFIG_SND_FM801_TEA575X_BOOL=y
CONFIG_SND_FM801_TEA575X=m
CONFIG_SND_HDA_INTEL=m
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
CONFIG_SND_KORG1212=m
CONFIG_SND_KORG1212_FIRMWARE_IN_KERNEL=y
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MAESTRO3_FIRMWARE_IN_KERNEL=y
CONFIG_SND_MIXART=m
CONFIG_SND_NM256=m
CONFIG_SND_PCXHR=m
CONFIG_SND_RIPTIDE=m
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m
CONFIG_SND_YMFPCI_FIRMWARE_IN_KERNEL=y
CONFIG_SND_AC97_POWER_SAVE=y
#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
CONFIG_SND_USB_CAIAQ=m
CONFIG_SND_USB_CAIAQ_INPUT=y
#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set
#
# SoC Audio support for SuperH
#
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_U132_HCD is not set
CONFIG_USB_SL811_HCD=m
CONFIG_USB_R8A66597_HCD=m
#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_KARMA=y
CONFIG_USB_LIBUSUAL=y
#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y
#
# USB port drivers
#
CONFIG_USB_USS720=m
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_BERRY_CHARGE=m
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_PHIDGET=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETMOTORCONTROL=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
# CONFIG_USB_TRANCEVIBRATOR is not set
CONFIG_USB_IOWARRIOR=m
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
#
# LED devices
#
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
#
# LED drivers
#
#
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
# CONFIG_INFINIBAND is not set
CONFIG_EDAC=y
#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_MM_EDAC=m
CONFIG_EDAC_AMD76X=m
CONFIG_EDAC_E7XXX=m
CONFIG_EDAC_E752X=m
CONFIG_EDAC_I82875P=m
CONFIG_EDAC_I82975X=m
CONFIG_EDAC_I3000=m
CONFIG_EDAC_I82860=m
CONFIG_EDAC_R82600=m
CONFIG_EDAC_I5000=m
#
# Real Time Clock
#
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
# CONFIG_RTC_DRV_TEST is not set
#
# I2C RTC drivers
#
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_MAX6900=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
CONFIG_RTC_DRV_M41T80=m
CONFIG_RTC_DRV_M41T80_WDT=y
#
# SPI RTC drivers
#
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=m
CONFIG_RTC_DRV_DS1553=m
CONFIG_RTC_DRV_STK17TA8=m
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_M48T86=m
CONFIG_RTC_DRV_M48T59=m
CONFIG_RTC_DRV_V3020=m
#
# on-CPU RTC drivers
#
#
# DMA Engine support
#
CONFIG_DMA_ENGINE=y
#
# DMA Clients
#
CONFIG_NET_DMA=y
#
# DMA Devices
#
CONFIG_INTEL_IOATDMA=m
# CONFIG_AUXDISPLAY is not set
CONFIG_VIRTUALIZATION=y
CONFIG_KVM=m
CONFIG_KVM_INTEL=m
CONFIG_KVM_AMD=m
#
# Userspace I/O
#
# CONFIG_UIO is not set
CONFIG_LGUEST=m
CONFIG_LGUEST_GUEST=y
#
# File systems
#
CONFIG_EXT2_FS=m
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=m
CONFIG_JBD_DEBUG=y
CONFIG_FS_MBCACHE=m
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
CONFIG_MINIX_FS=y
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
CONFIG_GENERIC_ACL=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
CONFIG_NTFS_DEBUG=y
CONFIG_NTFS_RW=y
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_ECRYPT_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
CONFIG_VXFS_FS=m
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
CONFIG_CIFS_STATS=y
CONFIG_CIFS_STATS2=y
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
CONFIG_LDM_DEBUG=y
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Distributed Lock Manager
#
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
CONFIG_INSTRUMENTATION=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
CONFIG_HEADERS_CHECK=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_SLUB_DEBUG_ON is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_DEBUG_RT_MUTEXES=y
CONFIG_DEBUG_PI_LIST=y
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_LOCKDEP is not set
CONFIG_TRACE_IRQFLAGS=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_DEBUG_LOCKING_API_SELFTESTS=y
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
CONFIG_FAULT_INJECTION=y
CONFIG_FAILSLAB=y
CONFIG_FAIL_PAGE_ALLOC=y
CONFIG_FAIL_MAKE_REQUEST=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
CONFIG_FAULT_INJECTION_STACKTRACE_FILTER=y
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set
#
# Page alloc debug is incompatible with Software Suspend on i386
#
CONFIG_DEBUG_RODATA=y
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y
#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=m
CONFIG_SECURITY_ROOTPLUG=m
# CONFIG_SECURITY_SELINUX is not set
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
# CONFIG_CRYPTO_TWOFISH_586 is not set
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=m
CONFIG_CRYPTO_DEV_PADLOCK_SHA=m
CONFIG_CRYPTO_DEV_GEODE=m
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y
[-- Attachment #1.3: dmesg.out --]
[-- Type: text/plain, Size: 42314 bytes --]
Inspecting /boot/System.map-2.6.22-git-gd7fff6f4-dirty
Loaded 27083 symbols from /boot/System.map-2.6.22-git-gd7fff6f4-dirty.
Symbols match kernel version 2.6.22.
No module symbols loaded - kernel modules not enabled.
klogd 1.4.1, log source = ksyslog started.
<5>[ 0.000000] Linux version 2.6.22-git-gd7fff6f4-dirty (ts@xenon) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #25 SMP PREEMPT Mon Jul 23 02:25:15 CEST 2007
<6>[ 0.000000] BIOS-provided physical RAM map:
<4>[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
<4>[ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
<4>[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
<4>[ 0.000000] BIOS-e820: 0000000000100000 - 000000003e584000 (usable)
<4>[ 0.000000] BIOS-e820: 000000003e584000 - 000000003e591000 (reserved)
<4>[ 0.000000] BIOS-e820: 000000003e591000 - 000000003e631000 (usable)
<4>[ 0.000000] BIOS-e820: 000000003e631000 - 000000003e6a4000 (ACPI NVS)
<4>[ 0.000000] BIOS-e820: 000000003e6a4000 - 000000003e6a9000 (ACPI data)
<4>[ 0.000000] BIOS-e820: 000000003e6a9000 - 000000003e6f2000 (ACPI NVS)
<4>[ 0.000000] BIOS-e820: 000000003e6f2000 - 000000003e6ff000 (ACPI data)
<4>[ 0.000000] BIOS-e820: 000000003e6ff000 - 000000003e700000 (usable)
<4>[ 0.000000] BIOS-e820: 000000003e700000 - 000000003f000000 (reserved)
<4>[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
<5>[ 0.000000] 103MB HIGHMEM available.
<5>[ 0.000000] 896MB LOWMEM available.
<6>[ 0.000000] found SMP MP-table at 000fe200
<7>[ 0.000000] Entering add_active_range(0, 0, 255744) 0 entries of 256 used
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] DMA 0 -> 4096
<4>[ 0.000000] Normal 4096 -> 229376
<4>[ 0.000000] HighMem 229376 -> 255744
<4>[ 0.000000] Movable zone start PFN for each node
<4>[ 0.000000] early_node_map[1] active PFN ranges
<4>[ 0.000000] 0: 0 -> 255744
<7>[ 0.000000] On node 0 totalpages: 255744
<7>[ 0.000000] DMA zone: 56 pages used for memmap
<7>[ 0.000000] DMA zone: 0 pages reserved
<7>[ 0.000000] DMA zone: 4040 pages, LIFO batch:0
<7>[ 0.000000] Normal zone: 3080 pages used for memmap
<7>[ 0.000000] Normal zone: 222200 pages, LIFO batch:31
<7>[ 0.000000] HighMem zone: 360 pages used for memmap
<7>[ 0.000000] HighMem zone: 26008 pages, LIFO batch:7
<7>[ 0.000000] Movable zone: 0 pages used for memmap
<6>[ 0.000000] DMI 2.4 present.
<4>[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL )
<4>[ 0.000000] ACPI: RSDT 3E6FD038, 0054 (r1 INTEL DQ965GF 15DB 1000013)
<4>[ 0.000000] ACPI: FACP 3E6FC000, 0074 (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: DSDT 3E6F7000, 40E9 (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: FACS 3E6AA000, 0040
<4>[ 0.000000] ACPI: APIC 3E6F6000, 0078 (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: WDDT 3E6F5000, 0040 (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: MCFG 3E6F4000, 003C (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: ASF! 3E6F3000, 00A6 (r32 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: HPET 3E6F2000, 0038 (r1 INTEL DQ965GF 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: SSDT 3E6A8000, 01BC (r1 INTEL CpuPm 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: SSDT 3E6A7000, 0175 (r1 INTEL Cpu0Ist 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: SSDT 3E6A6000, 0175 (r1 INTEL Cpu1Ist 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: SSDT 3E6A5000, 0175 (r1 INTEL Cpu2Ist 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: SSDT 3E6A4000, 0175 (r1 INTEL Cpu3Ist 15DB MSFT 1000013)
<4>[ 0.000000] ACPI: TCPA 3E6A9000, 0A3F (r1 INTEL TIANO 2 MSFT 1000013)
<6>[ 0.000000] ACPI: PM-Timer IO Port: 0x408
<7>[ 0.000000] ACPI: Local APIC address 0xfee00000
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>[ 0.000000] Processor #0 15:6 APIC version 20
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
<4>[ 0.000000] Processor #1 15:6 APIC version 20
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
<6>[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
<6>[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
<6>[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
<7>[ 0.000000] ACPI: IRQ0 used by override.
<7>[ 0.000000] ACPI: IRQ2 used by override.
<7>[ 0.000000] ACPI: IRQ9 used by override.
<4>[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
<6>[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
<6>[ 0.000000] Using ACPI (MADT) for SMP configuration information
<4>[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f000000:c0e00000)
<4>[ 0.000000] swsusp: Registered nosave memory region: 000000000008f000 - 00000000000a0000
<4>[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
<4>[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
<4>[ 0.000000] Built 1 zonelists in Zone order. Total pages: 252248
<5>[ 0.000000] Kernel command line: root=/dev/system/root video=matroxfb:vesa:0x31b resume=/dev/system/swap splash=verbose
<7>[ 0.000000] mapped APIC to ffffb000 (fee00000)
<7>[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
<6>[ 0.000000] Enabling fast FPU save and restore... done.
<6>[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
<6>[ 0.000000] Initializing CPU#0
<4>[ 0.000000] CPU 0 irqstacks, hard=c0435000 soft=c042d000
<4>[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>[ 0.000000] Detected 3197.059 MHz processor.
<4>[ 51.981918] Console: colour VGA+ 80x25
<6>[ 51.981924] console [tty0] enabled
<4>[ 51.987200] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
<4>[ 51.987291] ... MAX_LOCKDEP_SUBCLASSES: 8
<4>[ 51.987361] ... MAX_LOCK_DEPTH: 30
<4>[ 51.987431] ... MAX_LOCKDEP_KEYS: 2048
<4>[ 51.987501] ... CLASSHASH_SIZE: 1024
<4>[ 51.987571] ... MAX_LOCKDEP_ENTRIES: 8192
<4>[ 51.987641] ... MAX_LOCKDEP_CHAINS: 16384
<4>[ 51.987711] ... CHAINHASH_SIZE: 8192
<4>[ 51.987781] memory used by lock dependency info: 992 kB
<4>[ 51.987852] per task-struct memory footprint: 1200 bytes
<4>[ 51.987924] ------------------------
<4>[ 51.987993] | Locking API testsuite:
<4>[ 51.988061] ----------------------------------------------------------------------------
<4>[ 51.988153] | spin |wlock |rlock |mutex | wsem | rsem |
<4>[ 51.988245] --------------------------------------------------------------------------
<4>[ 51.988342] A-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.989215] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.990086] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.990966] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.991844] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.992741] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.993637] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.994566] double unlock: ok | ok | ok | ok | ok | ok |
<4>[ 51.995448] initialize held: ok | ok | ok | ok | ok | ok |
<4>[ 51.996328] bad unlock order: ok | ok | ok | ok | ok | ok |
<4>[ 51.997222] --------------------------------------------------------------------------
<4>[ 51.997314] recursive read-lock: | ok | | ok |
<4>[ 51.997794] recursive read-lock #2: | ok | | ok |
<4>[ 51.998274] mixed read-write-lock: | ok | | ok |
<4>[ 51.998755] mixed write-read-lock: | ok | | ok |
<4>[ 51.999235] --------------------------------------------------------------------------
<4>[ 51.999327] hard-irqs-on + irq-safe-A/12: ok | ok | ok |
<4>[ 51.999821] soft-irqs-on + irq-safe-A/12: ok | ok | ok |
<4>[ 52.000317] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
<4>[ 52.000809] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
<4>[ 52.001301] sirq-safe-A => hirqs-on/12: ok | ok | ok |
<4>[ 52.001795] sirq-safe-A => hirqs-on/21: ok | ok | ok |
<4>[ 52.002287] hard-safe-A + irqs-on/12: ok | ok | ok |
<4>[ 52.002779] soft-safe-A + irqs-on/12: ok | ok | ok |
<4>[ 52.003274] hard-safe-A + irqs-on/21: ok | ok | ok |
<4>[ 52.003767] soft-safe-A + irqs-on/21: ok | ok | ok |
<4>[ 52.004261] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
<4>[ 52.004761] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
<4>[ 52.005255] hard-safe-A + unsafe-B #1/132: ok | ok | ok |
<4>[ 52.005738] soft-safe-A + unsafe-B #1/132: ok | ok | ok |
<4>[ 52.006222] hard-safe-A + unsafe-B #1/213: ok | ok | ok |
<4>[ 52.006706] soft-safe-A + unsafe-B #1/213: ok | ok | ok |
<4>[ 52.007191] hard-safe-A + unsafe-B #1/231: ok | ok | ok |
<4>[ 52.007673] soft-safe-A + unsafe-B #1/231: ok | ok | ok |
<4>[ 52.008157] hard-safe-A + unsafe-B #1/312: ok | ok | ok |
<4>[ 52.008635] soft-safe-A + unsafe-B #1/312: ok | ok | ok |
<4>[ 52.009116] hard-safe-A + unsafe-B #1/321: ok | ok | ok |
<4>[ 52.009598] soft-safe-A + unsafe-B #1/321: ok | ok | ok |
<4>[ 52.010082] hard-safe-A + unsafe-B #2/123: ok | ok | ok |
<4>[ 52.010566] soft-safe-A + unsafe-B #2/123: ok | ok | ok |
<4>[ 52.011053] hard-safe-A + unsafe-B #2/132: ok | ok | ok |
<4>[ 52.011537] soft-safe-A + unsafe-B #2/132: ok | ok | ok |
<4>[ 52.012025] hard-safe-A + unsafe-B #2/213: ok | ok | ok |
<4>[ 52.012509] soft-safe-A + unsafe-B #2/213: ok | ok | ok |
<4>[ 52.012996] hard-safe-A + unsafe-B #2/231: ok | ok | ok |
<4>[ 52.013479] soft-safe-A + unsafe-B #2/231: ok | ok | ok |
<4>[ 52.013966] hard-safe-A + unsafe-B #2/312: ok | ok | ok |
<4>[ 52.014449] soft-safe-A + unsafe-B #2/312: ok | ok | ok |
<4>[ 52.014934] hard-safe-A + unsafe-B #2/321: ok | ok | ok |
<4>[ 52.015416] soft-safe-A + unsafe-B #2/321: ok | ok | ok |
<4>[ 52.015901] hard-irq lock-inversion/123: ok | ok | ok |
<4>[ 52.016385] soft-irq lock-inversion/123: ok | ok | ok |
<4>[ 52.016872] hard-irq lock-inversion/132: ok | ok | ok |
<4>[ 52.017355] soft-irq lock-inversion/132: ok | ok | ok |
<4>[ 52.017841] hard-irq lock-inversion/213: ok | ok | ok |
<4>[ 52.018325] soft-irq lock-inversion/213: ok | ok | ok |
<4>[ 52.018811] hard-irq lock-inversion/231: ok | ok | ok |
<4>[ 52.019294] soft-irq lock-inversion/231: ok | ok | ok |
<4>[ 52.019779] hard-irq lock-inversion/312: ok | ok | ok |
<4>[ 52.020263] soft-irq lock-inversion/312: ok | ok | ok |
<4>[ 52.020749] hard-irq lock-inversion/321: ok | ok | ok |
<4>[ 52.021232] soft-irq lock-inversion/321: ok | ok | ok |
<4>[ 52.021718] hard-irq read-recursion/123: ok |
<4>[ 52.021958] soft-irq read-recursion/123: ok |
<4>[ 52.022198] hard-irq read-recursion/132: ok |
<4>[ 52.022437] soft-irq read-recursion/132: ok |
<4>[ 52.022676] hard-irq read-recursion/213: ok |
<4>[ 52.024648] soft-irq read-recursion/213: ok |
<4>[ 52.024888] hard-irq read-recursion/231: ok |
<4>[ 52.025127] soft-irq read-recursion/231: ok |
<4>[ 52.025367] hard-irq read-recursion/312: ok |
<4>[ 52.025606] soft-irq read-recursion/312: ok |
<4>[ 52.025846] hard-irq read-recursion/321: ok |
<4>[ 52.026085] soft-irq read-recursion/321: ok |
<4>[ 52.026325] -------------------------------------------------------
<4>[ 52.026399] Good, all 218 testcases passed! |
<4>[ 52.026469] ---------------------------------
<6>[ 52.026770] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[ 52.027230] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 52.055519] Memory: 993276k/1022976k available (1963k kernel code, 28088k reserved, 1009k data, 248k init, 104596k highmem)
<4>[ 52.055624] virtual kernel memory layout:
<4>[ 52.055625] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
<4>[ 52.055626] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
<4>[ 52.055628] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
<4>[ 52.055629] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
<4>[ 52.055630] .init : 0xc03ec000 - 0xc042a000 ( 248 kB)
<4>[ 52.055631] .data : 0xc02eae55 - 0xc03e7624 (1009 kB)
<4>[ 52.055632] .text : 0xc0100000 - 0xc02eae55 (1963 kB)
<4>[ 52.056195] Checking if this processor honours the WP bit even in supervisor mode... Ok.
<6>[ 52.056378] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
<6>[ 52.056558] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
<6>[ 52.056820] hpet0: 3 64-bit timers, 14318180 Hz
<4>[ 52.117851] Calibrating delay using timer specific routine.. 6399.50 BogoMIPS (lpj=3199754)
<6>[ 52.118022] Security Framework v1.0.0 initialized
<4>[ 52.118115] Mount-cache hash table entries: 512
<7>[ 52.118579] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e4bd 00000000 00000001 00000000
<4>[ 52.118590] monitor/mwait feature present.
<4>[ 52.118660] using mwait in idle threads.
<6>[ 52.118734] CPU: Trace cache: 12K uops, L1 D cache: 16K
<6>[ 52.118865] CPU: L2 cache: 2048K
<6>[ 52.118934] CPU: Physical Processor ID: 0
<6>[ 52.119004] CPU: Processor Core ID: 0
<7>[ 52.119073] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e4bd 00000000 00000001 00000000
<6>[ 52.119083] Intel machine check architecture supported.
<6>[ 52.119159] Intel machine check reporting enabled on CPU#0.
<6>[ 52.119233] CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
<6>[ 52.119309] CPU0: Thermal monitoring enabled
<4>[ 52.119383] Compat vDSO mapped to ffffe000.
<6>[ 52.119465] Checking 'hlt' instruction... OK.
<4>[ 52.122987] lockdep: not fixing up alternatives.
<6>[ 52.123249] ACPI: Core revision 20070126
<4>[ 52.126974] CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
<4>[ 52.127168] lockdep: not fixing up alternatives.
<4>[ 52.127240] Booting processor 1/1 eip 3000
<4>[ 52.127311] CPU 1 irqstacks, hard=c0436000 soft=c042e000
<6>[ 52.137915] Initializing CPU#1
<4>[ 52.197767] Calibrating delay using timer specific routine.. 6393.68 BogoMIPS (lpj=3196841)
<7>[ 52.197775] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e4bd 00000000 00000001 00000000
<4>[ 52.197782] monitor/mwait feature present.
<6>[ 52.197787] CPU: Trace cache: 12K uops, L1 D cache: 16K
<6>[ 52.197789] CPU: L2 cache: 2048K
<6>[ 52.197792] CPU: Physical Processor ID: 0
<6>[ 52.197793] CPU: Processor Core ID: 1
<7>[ 52.197795] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e4bd 00000000 00000001 00000000
<6>[ 52.197801] Intel machine check architecture supported.
<6>[ 52.197808] Intel machine check reporting enabled on CPU#1.
<6>[ 52.197810] CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
<6>[ 52.197814] CPU1: Thermal monitoring enabled
<4>[ 52.198335] CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
<6>[ 52.199315] Total of 2 processors activated (12793.19 BogoMIPS).
<4>[ 52.199543] ENABLING IO-APIC IRQs
<6>[ 52.199812] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<6>[ 52.312848] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
<6>[ 52.332985] Brought up 2 CPUs
<6>[ 52.333612] Booting paravirtualized kernel on bare hardware
<6>[ 52.333938] NET: Registered protocol family 16
<6>[ 52.334494] ACPI: bus type pci registered
<3>[ 52.334790] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
<3>[ 52.334867] PCI: Not using MMCONFIG.
<6>[ 52.337438] PCI: Using configuration type 1
<4>[ 52.337508] Setting up standard PCI resources
<6>[ 52.348778] ACPI: Interpreter enabled
<6>[ 52.348851] ACPI: (supports S0 S3 S4 S5)
<6>[ 52.349182] ACPI: Using IOAPIC for interrupt routing
<6>[ 52.359802] ACPI: PCI Root Bridge [PCI0] (0000:00)
<4>[ 52.361156] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
<4>[ 52.361234] PCI quirk: region 0500-053f claimed by ICH6 GPIO
<6>[ 52.363156] PCI: Transparent bridge - 0000:00:1e.0
<7>[ 52.363330] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>[ 52.363912] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
<7>[ 52.364331] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
<7>[ 52.364484] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
<7>[ 52.364643] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
<7>[ 52.364795] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
<7>[ 52.364947] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
<4>[ 52.374028] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12)
<4>[ 52.374712] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
<4>[ 52.375390] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12)
<4>[ 52.376060] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
<4>[ 52.376729] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12)
<4>[ 52.377406] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)
<4>[ 52.378074] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 *10 11 12)
<4>[ 52.378744] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
<6>[ 52.379503] Linux Plug and Play Support v0.97 (c) Adam Belay
<6>[ 52.379663] pnp: PnP ACPI init
<6>[ 52.379754] ACPI: bus type pnp registered
<6>[ 52.384132] pnp: PnP ACPI: found 13 devices
<6>[ 52.384204] ACPI: ACPI bus type pnp unregistered
<6>[ 52.384815] PCI: Using ACPI for IRQ routing
<6>[ 52.384892] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<6>[ 52.389046] NetLabel: Initializing
<6>[ 52.389119] NetLabel: domain hash size = 128
<6>[ 52.389194] NetLabel: protocols = UNLABELED CIPSOv4
<6>[ 52.389300] NetLabel: unlabeled traffic allowed by default
<4>[ 52.389436] ACPI: RTC can wake from S4
<6>[ 52.389495] Time: tsc clocksource has been installed.
<6>[ 52.389668] pnp: 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved
<6>[ 52.389749] pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
<6>[ 52.389831] pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
<6>[ 52.389913] pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
<6>[ 52.390000] pnp: 00:06: ioport range 0x500-0x53f has been reserved
<6>[ 52.390082] pnp: 00:06: ioport range 0x400-0x47f has been reserved
<6>[ 52.390157] pnp: 00:06: ioport range 0x680-0x6ff has been reserved
<6>[ 52.390240] pnp: 00:07: iomem range 0xfed40000-0xfed44fff has been reserved
<6>[ 52.421185] PCI: Bridge: 0000:00:1c.0
<6>[ 52.421255] IO window: disabled.
<6>[ 52.421333] MEM window: 52d00000-52dfffff
<6>[ 52.421406] PREFETCH window: disabled.
<6>[ 52.421480] PCI: Bridge: 0000:00:1c.1
<6>[ 52.421550] IO window: 2000-2fff
<6>[ 52.421623] MEM window: 52a00000-52afffff
<6>[ 52.421695] PREFETCH window: disabled.
<6>[ 52.421768] PCI: Bridge: 0000:00:1c.2
<6>[ 52.421837] IO window: disabled.
<6>[ 52.421909] MEM window: 52e00000-52efffff
<6>[ 52.421982] PREFETCH window: disabled.
<6>[ 52.422057] PCI: Bridge: 0000:04:00.0
<6>[ 52.422132] IO window: disabled.
<6>[ 52.422207] MEM window: 52000000-528fffff
<6>[ 52.422282] PREFETCH window: 50000000-51ffffff
<6>[ 52.422362] PCI: Bridge: 0000:00:1c.3
<6>[ 52.422431] IO window: disabled.
<6>[ 52.422504] MEM window: 52000000-528fffff
<6>[ 52.422576] PREFETCH window: 50000000-51ffffff
<6>[ 52.422651] PCI: Bridge: 0000:00:1c.4
<6>[ 52.422719] IO window: disabled.
<6>[ 52.422792] MEM window: 52f00000-52ffffff
<6>[ 52.422864] PREFETCH window: disabled.
<6>[ 52.422939] PCI: Bridge: 0000:00:1e.0
<6>[ 52.423010] IO window: 1000-1fff
<6>[ 52.423086] MEM window: 52900000-529fffff
<6>[ 52.423162] PREFETCH window: 53000000-530fffff
<6>[ 52.423263] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
<7>[ 52.423409] PCI: Setting latency timer of device 0000:00:1c.0 to 64
<6>[ 52.423437] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
<7>[ 52.423579] PCI: Setting latency timer of device 0000:00:1c.1 to 64
<6>[ 52.423605] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>[ 52.423746] PCI: Setting latency timer of device 0000:00:1c.2 to 64
<6>[ 52.423771] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
<7>[ 52.423911] PCI: Setting latency timer of device 0000:00:1c.3 to 64
<7>[ 52.423936] PCI: Setting latency timer of device 0000:04:00.0 to 64
<6>[ 52.423960] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
<7>[ 52.424104] PCI: Setting latency timer of device 0000:00:1c.4 to 64
<7>[ 52.424120] PCI: Setting latency timer of device 0000:00:1e.0 to 64
<6>[ 52.424131] NET: Registered protocol family 2
<6>[ 52.433499] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 52.433866] TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
<6>[ 52.440677] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
<6>[ 52.447243] TCP: Hash tables configured (established 65536 bind 65536)
<6>[ 52.447346] TCP reno registered
<6>[ 52.449843] checking if image is initramfs...<6>Switched to high resolution mode on CPU 1
<6>[ 52.687416] Switched to high resolution mode on CPU 0
<4>[ 52.721223] it is
<6>[ 53.024003] Freeing initrd memory: 7480k freed
<6>[ 53.024980] Machine check exception polling timer started.
<6>[ 53.025105] apm: BIOS not found.
<6>[ 53.025989] audit: initializing netlink socket (disabled)
<5>[ 53.026104] audit(1185150709.707:1): initialized
<4>[ 53.026465] highmem bounce pool size: 64 pages
<4>[ 53.026540] Total HugeTLB memory allocated, 0
<5>[ 53.033289] VFS: Disk quotas dquot_6.5.1
<4>[ 53.033497] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>[ 53.034308] io scheduler noop registered
<6>[ 53.034384] io scheduler anticipatory registered
<6>[ 53.034455] io scheduler deadline registered (default)
<6>[ 53.034544] io scheduler cfq registered
<7>[ 53.034967] Boot video device is 0000:05:00.0
<7>[ 53.035238] PCI: Setting latency timer of device 0000:00:1c.0 to 64
<4>[ 53.035298] assign_interrupt_mode Found MSI capability
<7>[ 53.035419] Allocate Port Service[0000:00:1c.0:pcie00]
<7>[ 53.035513] Allocate Port Service[0000:00:1c.0:pcie02]
<7>[ 53.035680] PCI: Setting latency timer of device 0000:00:1c.1 to 64
<4>[ 53.035738] assign_interrupt_mode Found MSI capability
<7>[ 53.035856] Allocate Port Service[0000:00:1c.1:pcie00]
<7>[ 53.035947] Allocate Port Service[0000:00:1c.1:pcie02]
<7>[ 53.036121] PCI: Setting latency timer of device 0000:00:1c.2 to 64
<4>[ 53.036180] assign_interrupt_mode Found MSI capability
<7>[ 53.036299] Allocate Port Service[0000:00:1c.2:pcie00]
<7>[ 53.036391] Allocate Port Service[0000:00:1c.2:pcie02]
<7>[ 53.036560] PCI: Setting latency timer of device 0000:00:1c.3 to 64
<4>[ 53.036618] assign_interrupt_mode Found MSI capability
<7>[ 53.036735] Allocate Port Service[0000:00:1c.3:pcie00]
<7>[ 53.036827] Allocate Port Service[0000:00:1c.3:pcie02]
<7>[ 53.036995] PCI: Setting latency timer of device 0000:00:1c.4 to 64
<4>[ 53.037062] assign_interrupt_mode Found MSI capability
<7>[ 53.037182] Allocate Port Service[0000:00:1c.4:pcie00]
<7>[ 53.037268] Allocate Port Service[0000:00:1c.4:pcie02]
<6>[ 53.037806] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
<6>[ 53.039691] matroxfb: Matrox G550 detected
<6>[ 53.040802] PInS memtype = 5
<6>[ 53.041772] matroxfb: MTRR's turned on
<6>[ 53.041890] matroxfb: 1280x1024x32bpp (virtual: 1280x3276)
<6>[ 53.041981] matroxfb: framebuffer at 0x50000000, mapped to 0xf8880000, size 33554432
<6>[ 53.042265] fbcon: MATROX (fb0) is primary device
<4>[ 53.063196] Console: switching to colour frame buffer device 160x64
<4>[ 53.070886] fb0: MATROX frame buffer device
<6>[ 53.071109] matroxfb_crtc2: secondary head of fb0 was registered as fb1
<6>[ 53.127900] Real Time Clock Driver v1.12ac
<7>[ 53.128206] hpet_resources: 0xfed00000 is busy
<6>[ 53.128238] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>[ 53.129398] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<4>[ 56.138468] floppy0: no floppy controllers found
<4>[ 56.140164] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>[ 56.140707] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
<4>[ 56.140790] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
<6>[ 56.141480] serio: i8042 KBD port at 0x60,0x64 irq 1
<6>[ 56.141854] mice: PS/2 mouse device common for all mice
<6>[ 56.167366] input: AT Translated Set 2 keyboard as /class/input/input0
<6>[ 56.167827] input: PC Speaker as /class/input/input1
<6>[ 56.168114] NET: Registered protocol family 1
<6>[ 56.168182] Starting balanced_irq
<4>[ 56.168276] Using IPI No-Shortcut mode
<6>[ 56.169065] Freeing unused kernel memory: 248k freed
<4>[ 56.169160] Write protecting the kernel read-only data: 798k
<5>[ 56.709874] SCSI subsystem initialized
<6>[ 56.725249] ACPI: Processor [CPU0] (supports 8 throttling states)
<6>[ 56.725478] ACPI: Processor [CPU1] (supports 8 throttling states)
<4>[ 56.725619] ACPI Exception (processor_core-0778): AE_NOT_FOUND, Processor Device is not present [20070126]
<4>[ 56.725786] ACPI Exception (processor_core-0778): AE_NOT_FOUND, Processor Device is not present [20070126]
<7>[ 56.745143] libata version 2.21 loaded.
<7>[ 56.752402] ahci 0000:00:1f.2: version 2.3
<6>[ 56.752436] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
<6>[ 57.753129] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
<6>[ 57.757366] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
<7>[ 57.761624] PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>[ 57.762065] scsi0 : ahci
<6>[ 57.766534] scsi1 : ahci
<6>[ 57.770901] scsi2 : ahci
<6>[ 57.775209] scsi3 : ahci
<6>[ 57.779461] scsi4 : ahci
<6>[ 57.783621] scsi5 : ahci
<6>[ 57.787755] ata1: SATA max UDMA/133 cmd 0xf886e100 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 57.791965] ata2: SATA max UDMA/133 cmd 0xf886e180 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 57.796128] ata3: SATA max UDMA/133 cmd 0xf886e200 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 57.800260] ata4: SATA max UDMA/133 cmd 0xf886e280 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 57.804418] ata5: SATA max UDMA/133 cmd 0xf886e300 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 57.808600] ata6: SATA max UDMA/133 cmd 0xf886e380 ctl 0x00000000 bmdma 0x00000000 irq 218
<6>[ 58.268043] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
<6>[ 58.326729] ata1.00: ATA-7: ST380811AS, 3.AAE, max UDMA/133
<6>[ 58.331010] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
<6>[ 58.384974] ata1.00: configured for UDMA/133
<6>[ 58.847011] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
<6>[ 58.907334] ata2.00: ATA-7: ST380811AS, 3.AAE, max UDMA/133
<6>[ 58.911595] ata2.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
<6>[ 58.965574] ata2.00: configured for UDMA/133
<6>[ 59.273243] ata3: SATA link down (SStatus 0 SControl 300)
<6>[ 59.580008] ata4: SATA link down (SStatus 0 SControl 300)
<6>[ 59.887772] ata5: SATA link down (SStatus 0 SControl 300)
<6>[ 60.194536] ata6: SATA link down (SStatus 0 SControl 300)
<5>[ 60.198823] scsi 0:0:0:0: Direct-Access ATA ST380811AS 3.AA PQ: 0 ANSI: 5
<5>[ 60.203142] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
<5>[ 60.207307] sd 0:0:0:0: [sda] Write Protect is off
<7>[ 60.211378] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>[ 60.211421] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>[ 60.215669] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
<5>[ 60.219816] sd 0:0:0:0: [sda] Write Protect is off
<7>[ 60.223891] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<5>[ 60.223934] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>[ 60.228066] sda: sda1 sda2
<5>[ 60.259503] sd 0:0:0:0: [sda] Attached SCSI disk
<5>[ 60.263742] scsi 1:0:0:0: Direct-Access ATA ST380811AS 3.AA PQ: 0 ANSI: 5
<5>[ 60.268565] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
<5>[ 60.273836] sd 1:0:0:0: [sdb] Write Protect is off
<7>[ 60.277984] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>[ 60.278034] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<5>[ 60.282382] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
<5>[ 60.286666] sd 1:0:0:0: [sdb] Write Protect is off
<5>[ 60.286897] sd 0:0:0:0: Attached scsi generic sg0 type 0
<7>[ 60.295163] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>[ 60.295209] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>[ 60.299504] sdb: sdb1
<5>[ 60.324402] sd 1:0:0:0: [sdb] Attached SCSI disk
<5>[ 60.328825] sd 1:0:0:0: Attached scsi generic sg1 type 0
<6>[ 60.343105] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16
<7>[ 60.343154] PCI: Setting latency timer of device 0000:02:00.0 to 64
<6>[ 60.343220] scsi6 : pata_marvell
<6>[ 60.343313] scsi7 : pata_marvell
<6>[ 60.343378] ata7: PATA max UDMA/100 cmd 0x00012018 ctl 0x00012026 bmdma 0x00012000 irq 16
<6>[ 60.343381] ata8: DUMMY
<4>[ 60.343411] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00
<6>[ 60.803423] ata7.00: ATAPI: HL-DT-STDVD-ROM GDR8164B, 0L06, max UDMA/33
<6>[ 60.808314] ata7.01: ATAPI: TSSTcorpCD/DVDW SH-S182M, SB03, max UDMA/33
<6>[ 60.971285] ata7.00: configured for UDMA/33
<6>[ 61.150279] ata7.01: configured for UDMA/33
<5>[ 61.158529] scsi 6:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
<5>[ 61.163619] scsi 6:0:0:0: Attached scsi generic sg2 type 5
<5>[ 61.169552] scsi 6:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-S182M SB03 PQ: 0 ANSI: 5
<5>[ 61.174616] scsi 6:0:1:0: Attached scsi generic sg3 type 5
<6>[ 61.209943] ACPI: PCI Interrupt 0000:07:01.0[A] -> GSI 22 (level, low) -> IRQ 20
<4>[ 61.214120] sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
<6>[ 61.214125] Uniform CD-ROM driver Revision: 3.20
<7>[ 61.216680] sr 6:0:0:0: Attached scsi CD-ROM sr0
<4>[ 61.236407] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
<7>[ 61.245736] sr 6:0:1:0: Attached scsi CD-ROM sr1
<6>[ 66.432921] scsi8 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<4>[ 66.432925] <Adaptec 29160B Ultra160 SCSI adapter>
<4>[ 66.432926] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
<4>[ 66.432928]
<6>[ 66.477058] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<6>[ 66.491400] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<6>[ 67.350626] kjournald starting. Commit interval 5 seconds
<6>[ 67.355960] EXT3 FS on dm-1, internal journal
<6>[ 67.361292] EXT3-fs: mounted filesystem with ordered data mode.
<5>[ 69.275070] scsi 8:0:12:0: Sequential-Access HP C5683A C111 PQ: 0 ANSI: 2
<6>[ 69.280118] target8:0:12: Beginning Domain Validation
<6>[ 69.288560] target8:0:12: wide asynchronous
<6>[ 69.296061] target8:0:12: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 32)
<6>[ 69.303057] target8:0:12: Domain Validation skipping write tests
<6>[ 69.307966] target8:0:12: Ending Domain Validation
<6>[ 69.729833] parport_pc 00:08: reported by Plug and Play ACPI
<6>[ 69.734704] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
<6>[ 69.822471] lp0: using parport0 (interrupt-driven).
<5>[ 70.083318] scsi 8:0:12:0: Attached scsi generic sg4 type 1
<6>[ 71.185895] st: Version 20070203, fixed bufsize 32768, s/g segs 256
<5>[ 71.190999] st 8:0:12:0: Attached scsi tape st0
<6>[ 71.198463] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
<6>[ 71.201845] st 8:0:12:0: st0: try direct i/o: yes (alignment 512 B)
<6>[ 71.207709] Copyright (c) 1999-2006 Intel Corporation.
<6>[ 71.212614] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 21
<7>[ 71.217503] PCI: Setting latency timer of device 0000:00:19.0 to 64
<6>[ 71.234730] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:03:d8:ff
<6>[ 71.284403] Linux agpgart interface v0.102
<6>[ 71.319116] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
<6>[ 71.350541] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 21 (level, low) -> IRQ 22
<6>[ 71.566726] usbcore: registered new interface driver usbfs
<6>[ 71.571505] usbcore: registered new interface driver hub
<6>[ 71.576144] usbcore: registered new device driver usb
<6>[ 71.589773] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
<4>[ 71.594485] rtc_cmos: probe of 00:03 failed with error -16
<6>[ 71.625007] agpgart: Detected an Intel 965Q Chipset.
<6>[ 71.630265] agpgart: Unknown page table size, assuming 512KB
<6>[ 71.634725] agpgart: Detected 7676K stolen memory.
<6>[ 71.702449] agpgart: AGP aperture is 256M @ 0x40000000
<6>[ 71.707062] ACPI: PCI Interrupt 0000:07:03.0[A] -> GSI 19 (level, low) -> IRQ 19
<6>[ 71.739492] USB Universal Host Controller Interface driver v3.0
<6>[ 71.744070] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17
<7>[ 71.748591] PCI: Setting latency timer of device 0000:00:1a.0 to 64
<6>[ 71.748605] uhci_hcd 0000:00:1a.0: UHCI Host Controller
<6>[ 71.753546] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
<6>[ 71.758038] uhci_hcd 0000:00:1a.0: irq 17, io base 0x000030c0
<6>[ 71.770691] usb usb1: configuration #1 chosen from 1 choice
<6>[ 71.775204] hub 1-0:1.0: USB hub found
<6>[ 71.779647] hub 1-0:1.0: 2 ports detected
<5>[ 71.779658] firewire_ohci: Added fw-ohci device 0000:07:03.0, OHCI version 1.10
<6>[ 71.889835] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 22
<7>[ 71.894436] PCI: Setting latency timer of device 0000:00:1a.1 to 64
<6>[ 71.894442] uhci_hcd 0000:00:1a.1: UHCI Host Controller
<6>[ 71.899069] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
<6>[ 71.903676] uhci_hcd 0000:00:1a.1: irq 22, io base 0x000030a0
<6>[ 71.908442] usb usb2: configuration #1 chosen from 1 choice
<6>[ 71.913041] hub 2-0:1.0: USB hub found
<6>[ 71.917650] hub 2-0:1.0: 2 ports detected
<6>[ 72.022666] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
<7>[ 72.027350] PCI: Setting latency timer of device 0000:00:1d.0 to 64
<6>[ 72.027356] uhci_hcd 0000:00:1d.0: UHCI Host Controller
<6>[ 72.032018] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
<6>[ 72.036666] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
<6>[ 72.041589] usb usb3: configuration #1 chosen from 1 choice
<6>[ 72.046268] hub 3-0:1.0: USB hub found
<6>[ 72.050969] hub 3-0:1.0: 2 ports detected
<6>[ 72.156643] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
<7>[ 72.161458] PCI: Setting latency timer of device 0000:00:1a.7 to 64
<6>[ 72.161465] ehci_hcd 0000:00:1a.7: EHCI Host Controller
<6>[ 72.166252] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
<6>[ 72.171161] ehci_hcd 0000:00:1a.7: debug port 1
<7>[ 72.175979] PCI: cache line size of 128 is not supported by device 0000:00:1a.7
<6>[ 72.175996] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x52c25c00
<6>[ 72.184751] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>[ 72.189774] usb usb4: configuration #1 chosen from 1 choice
<6>[ 72.194610] hub 4-0:1.0: USB hub found
<6>[ 72.199467] hub 4-0:1.0: 4 ports detected
<5>[ 72.288426] firewire_core: created new fw device fw0 (0 config rom retries, S400)
<6>[ 72.304440] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
<7>[ 72.309353] PCI: Setting latency timer of device 0000:00:1d.7 to 64
<6>[ 72.309358] ehci_hcd 0000:00:1d.7: EHCI Host Controller
<6>[ 72.314260] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
<6>[ 72.319180] ehci_hcd 0000:00:1d.7: debug port 1
<7>[ 72.324056] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
<6>[ 72.324065] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x52c25800
<6>[ 72.332882] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<6>[ 72.338033] usb usb5: configuration #1 chosen from 1 choice
<6>[ 72.342957] hub 5-0:1.0: USB hub found
<6>[ 72.347836] hub 5-0:1.0: 6 ports detected
<6>[ 72.453988] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
<7>[ 72.458979] PCI: Setting latency timer of device 0000:00:1d.1 to 64
<6>[ 72.458985] uhci_hcd 0000:00:1d.1: UHCI Host Controller
<6>[ 72.481089] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
<6>[ 72.485997] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
<6>[ 72.491140] usb usb6: configuration #1 chosen from 1 choice
<6>[ 72.496038] hub 6-0:1.0: USB hub found
<6>[ 72.500847] hub 6-0:1.0: 2 ports detected
<6>[ 72.607563] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
<7>[ 72.612469] PCI: Setting latency timer of device 0000:00:1d.2 to 64
<6>[ 72.612475] uhci_hcd 0000:00:1d.2: UHCI Host Controller
<6>[ 72.617459] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
<6>[ 72.622426] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
<6>[ 72.627577] usb usb7: configuration #1 chosen from 1 choice
<6>[ 72.632545] hub 7-0:1.0: USB hub found
<6>[ 72.637471] hub 7-0:1.0: 2 ports detected
<6>[ 72.744162] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 20
<7>[ 72.749959] PCI: Setting latency timer of device 0000:00:1b.0 to 64
<7>[ 72.777049] ALSA sound/pci/hda/hda_codec.c:2331: autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0)
<7>[ 72.777056] ALSA sound/pci/hda/hda_codec.c:2335: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<7>[ 72.777060] ALSA sound/pci/hda/hda_codec.c:2339: hp_outs=1 (0xa/0x0/0x0/0x0/0x0)
<7>[ 72.777063] ALSA sound/pci/hda/hda_codec.c:2347: inputs: mic=0xe, fmic=0xb, line=0xf, fline=0x0, cd=0x0, aux=0x0
<7>[ 72.777444] ALSA sound/pci/hda/patch_sigmatel.c:1297: dac_nids=3 (0x2/0x5/0x4/0x0/0x0)
<6>[ 72.822812] usb 6-2: new low speed USB device using uhci_hcd and address 2
<6>[ 72.969661] usb 6-2: configuration #1 chosen from 1 choice
<6>[ 73.017680] Adding 2097144k swap on /dev/system/swap. Priority:-1 extents:1 across:2097144k
<6>[ 73.073573] usbcore: registered new interface driver hiddev
<6>[ 73.091628] input: HID 413c:3010 as /class/input/input2
<6>[ 73.096726] input: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:1d.1-2
<6>[ 73.101865] usbcore: registered new interface driver usbhid
<6>[ 73.106889] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<6>[ 75.506605] loop: module loaded
<6>[ 75.539569] kjournald starting. Commit interval 5 seconds
<6>[ 75.543832] EXT3 FS on sda1, internal journal
<6>[ 75.548112] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 75.569708] kjournald starting. Commit interval 5 seconds
<6>[ 75.573982] EXT3 FS on dm-0, internal journal
<6>[ 75.578225] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 75.614378] kjournald starting. Commit interval 5 seconds
<6>[ 75.618549] EXT3 FS on dm-3, internal journal
<6>[ 75.622763] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 75.657297] kjournald starting. Commit interval 5 seconds
<6>[ 75.661434] EXT3 FS on dm-4, internal journal
<6>[ 75.665590] EXT3-fs: mounted filesystem with ordered data mode.
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 250 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 10:25 ` Tilman Schmidt
@ 2007-07-23 14:51 ` Jeremy Fitzhardinge
2007-07-23 19:42 ` Tilman Schmidt
0 siblings, 1 reply; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-23 14:51 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, andi, nix.or.die
Tilman Schmidt wrote:
> Attached are .config and dmesg (as captured in SuSE's /var/log/boot.msg)
> of a CONFIG_XEN=n git-current build.
That's dmesg from a successful boot? What does it look like when its
unsuccessful? Where do they start to differ?
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 14:51 ` Jeremy Fitzhardinge
@ 2007-07-23 19:42 ` Tilman Schmidt
2007-07-23 20:32 ` Jeremy Fitzhardinge
0 siblings, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-23 19:42 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: LKML, andi, nix.or.die
[-- Attachment #1.1: Type: text/plain, Size: 1318 bytes --]
Am 23.07.2007 16:51 schrieb Jeremy Fitzhardinge:
> Tilman Schmidt wrote:
>> Attached are .config and dmesg (as captured in SuSE's /var/log/boot.msg)
>> of a CONFIG_XEN=n git-current build.
>
> That's dmesg from a successful boot?
Yes.
> What does it look like when its
> unsuccessful? Where do they start to differ?
To answer that, I have reproduced the effect with kernel 2.6.23-rc1 with
netconsole compiled in. I'm attaching both captures, for CONFIG_XEN=y
(unsuccessful) as well CONFIG_XEN=n (successful).
The first noticeable difference is that the nonzero timestamps starting
after the line "Detected 3197.059 MHz processor" are much bigger with XEN -
but perhaps that's expected.
More to the point, everything from:
SCSI subsystem initialized
on is completely missing, including all the [S/P]ATA, SCSI, parport, AGP,
USB, Firewire, RTC and of course ext3 messages. Only the "device-mapper"
line still appears.
Btw, the NULL pointer BUG at the end of the successful boot is new with
2.6.23-rc1. I'll report that separately but didn't want to edit anything.
HTH
T.
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #1.2: netconsole-2.6.23-rc1-xen --]
[-- Type: text/plain, Size: 23761 bytes --]
[ 0.000000] Linux version 2.6.23-rc1-xentest (ts@xenon) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #4 SMP PREEMPT Mon Jul 23 20:02:38 CEST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003e584000 (usable)
[ 0.000000] BIOS-e820: 000000003e584000 - 000000003e591000 (reserved)
[ 0.000000] BIOS-e820: 000000003e591000 - 000000003e631000 (usable)
[ 0.000000] BIOS-e820: 000000003e631000 - 000000003e6a4000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003e6a4000 - 000000003e6a9000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003e6a9000 - 000000003e6f2000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003e6f2000 - 000000003e6ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003e6ff000 - 000000003e700000 (usable)
[ 0.000000] BIOS-e820: 000000003e700000 - 000000003f000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] 103MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fe200
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 255744
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 255744
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL )
[ 0.000000] ACPI: RSDT 3E6FD038, 0054 (r1 INTEL DQ965GF 15DB 1000013)
[ 0.000000] ACPI: FACP 3E6FC000, 0074 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: DSDT 3E6F7000, 40E9 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: FACS 3E6AA000, 0040
[ 0.000000] ACPI: APIC 3E6F6000, 0078 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: WDDT 3E6F5000, 0040 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: MCFG 3E6F4000, 003C (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: ASF! 3E6F3000, 00A6 (r32 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: HPET 3E6F2000, 0038 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A8000, 01BC (r1 INTEL CpuPm 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A7000, 0175 (r1 INTEL Cpu0Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A6000, 0175 (r1 INTEL Cpu1Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A5000, 0175 (r1 INTEL Cpu2Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A4000, 0175 (r1 INTEL Cpu3Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: TCPA 3E6A9000, 0A3F (r1 INTEL TIANO 2 MSFT 1000013)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f000000:c0e00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000008f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order. Total pages: 252248
[ 0.000000] Kernel command line: root=/dev/system/root video=matroxfb:vesa:0x31b resume=/dev/system/swap splash=verbose netconsole=6665@192.168.59.102/eth0,6666@192.168.59.127/00:50:da:82:a0:46
[ 0.000000] netconsole: local port 6665
[ 0.000000] netconsole: local IP 192.168.59.102
[ 0.000000] netconsole: interface eth0
[ 0.000000] netconsole: remote port 6666
[ 0.000000] netconsole: remote IP 192.168.59.127
[ 0.000000] netconsole: remote ethernet address 00:50:da:82:a0:46
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] CPU 0 irqstacks, hard=c0463000 soft=c045b000
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 3197.106 MHz processor.
[ 191.420290] Console: colour VGA+ 80x25
[ 191.420297] console [tty0] enabled
[ 191.426015] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 191.426107] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 191.426177] ... MAX_LOCK_DEPTH: 30
[ 191.426246] ... MAX_LOCKDEP_KEYS: 2048
[ 191.426316] ... CLASSHASH_SIZE: 1024
[ 191.426386] ... MAX_LOCKDEP_ENTRIES: 8192
[ 191.426456] ... MAX_LOCKDEP_CHAINS: 16384
[ 191.426526] ... CHAINHASH_SIZE: 8192
[ 191.426597] memory used by lock dependency info: 992 kB
[ 191.426669] per task-struct memory footprint: 1200 bytes
[ 191.426741] ------------------------
[ 191.426809] | Locking API testsuite:
[ 191.426878] ----------------------------------------------------------------------------
[ 191.426970] | spin |wlock |rlock |mutex | wsem | rsem |
[ 191.427061] --------------------------------------------------------------------------
[ 191.427158] A-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.428041] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.428922] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.429815] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
[ 191.430708] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.431619] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.432529] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 191.433441] double unlock: ok | ok | ok | ok | ok | ok |
[ 191.434301] initialize held: ok | ok | ok | ok | ok | ok |
[ 191.435160] bad unlock order: ok | ok | ok | ok | ok | ok |
[ 191.436036] --------------------------------------------------------------------------
[ 191.436128] recursive read-lock: | ok | | ok |
[ 191.436601] recursive read-lock #2: | ok | | ok |
[ 191.437075] mixed read-write-lock: | ok | | ok |
[ 191.437549] mixed write-read-lock: | ok | | ok |
[ 191.438024] --------------------------------------------------------------------------
[ 191.438116] hard-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 191.438597] soft-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 191.439080] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 191.439563] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 191.440048] sirq-safe-A => hirqs-on/12: ok | ok | ok |
[ 191.440534] sirq-safe-A => hirqs-on/21: ok | ok | ok |
[ 191.441020] hard-safe-A + irqs-on/12: ok | ok | ok |
[ 191.441504] soft-safe-A + irqs-on/12: ok | ok | ok |
[ 191.441991] hard-safe-A + irqs-on/21: ok | ok | ok |
[ 191.442476] soft-safe-A + irqs-on/21: ok | ok | ok |
[ 191.442962] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 191.443455] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 191.443949] hard-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 191.444441] soft-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 191.444934] hard-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 191.445426] soft-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 191.445919] hard-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 191.446410] soft-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 191.446902] hard-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 191.447390] soft-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 191.447879] hard-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 191.448370] soft-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 191.448862] hard-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 191.449355] soft-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 191.449851] hard-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 191.450343] soft-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 191.450837] hard-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 191.451329] soft-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 191.451824] hard-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 191.452314] soft-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 191.452808] hard-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 191.453300] soft-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 191.453795] hard-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 191.454286] soft-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 191.454780] hard-irq lock-inversion/123: ok | ok | ok |
[ 191.455273] soft-irq lock-inversion/123: ok | ok | ok |
[ 191.455770] hard-irq lock-inversion/132: ok | ok | ok |
[ 191.456263] soft-irq lock-inversion/132: ok | ok | ok |
[ 191.456760] hard-irq lock-inversion/213: ok | ok | ok |
[ 191.457253] soft-irq lock-inversion/213: ok | ok | ok |
[ 191.457749] hard-irq lock-inversion/231: ok | ok | ok |
[ 191.458242] soft-irq lock-inversion/231: ok | ok | ok |
[ 191.458737] hard-irq lock-inversion/312: ok | ok | ok |
[ 191.459231] soft-irq lock-inversion/312: ok | ok | ok |
[ 191.461452] hard-irq lock-inversion/321: ok | ok | ok |
[ 191.461944] soft-irq lock-inversion/321: ok | ok | ok |
[ 191.462440] hard-irq read-recursion/123: ok |
[ 191.462684] soft-irq read-recursion/123: ok |
[ 191.462928] hard-irq read-recursion/132: ok |
[ 191.463170] soft-irq read-recursion/132: ok |
[ 191.463414] hard-irq read-recursion/213: ok |
[ 191.463657] soft-irq read-recursion/213: ok |
[ 191.463901] hard-irq read-recursion/231: ok |
[ 191.464143] soft-irq read-recursion/231: ok |
[ 191.464386] hard-irq read-recursion/312: ok |
[ 191.464629] soft-irq read-recursion/312: ok |
[ 191.464874] hard-irq read-recursion/321: ok |
[ 191.465117] soft-irq read-recursion/321: ok |
[ 191.465360] -------------------------------------------------------
[ 191.465435] Good, all 218 testcases passed! |
[ 191.465505] ---------------------------------
[ 191.465808] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 191.466266] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 191.494322] Memory: 993204k/1022976k available (2079k kernel code, 28052k reserved, 1067k data, 256k init, 104596k highmem)
[ 191.494428] virtual kernel memory layout:
[ 191.494429] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 191.494430] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 191.494431] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 191.494433] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 191.494434] .init : 0xc0417000 - 0xc0457000 ( 256 kB)
[ 191.494435] .data : 0xc0307f2a - 0xc0412e64 (1067 kB)
[ 191.494436] .text : 0xc0100000 - 0xc0307f2a (2079 kB)
[ 191.495000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 191.495185] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 191.495363] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 191.495624] hpet0: 3 64-bit timers, 14318180 Hz
[ 191.556656] Calibrating delay using timer specific routine.. 6399.65 BogoMIPS (lpj=3199828)
[ 191.556827] Security Framework v1.0.0 initialized
[ 191.556920] Mount-cache hash table entries: 512
[ 191.557408] monitor/mwait feature present.
[ 191.557478] using mwait in idle threads.
[ 191.557553] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 191.557684] CPU: L2 cache: 2048K
[ 191.557754] CPU: Physical Processor ID: 0
[ 191.557823] CPU: Processor Core ID: 0
[ 191.557902] Intel machine check architecture supported.
[ 191.557979] Intel machine check reporting enabled on CPU#0.
[ 191.558053] CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
[ 191.558128] CPU0: Thermal monitoring enabled
[ 191.558202] Compat vDSO mapped to ffffe000.
[ 191.558285] Checking 'hlt' instruction... OK.
[ 191.561978] lockdep: not fixing up alternatives.
[ 191.563203] ACPI: Core revision 20070126
[ 191.566968] CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
[ 191.567162] lockdep: not fixing up alternatives.
[ 191.567234] Booting processor 1/1 eip 3000
[ 191.567305] CPU 1 irqstacks, hard=c0464000 soft=c045c000
[ 191.577916] Initializing CPU#1
[ 191.637570] Calibrating delay using timer specific routine.. 6393.68 BogoMIPS (lpj=3196843)
[ 191.637586] monitor/mwait feature present.
[ 191.637592] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 191.637594] CPU: L2 cache: 2048K
[ 191.637596] CPU: Physical Processor ID: 0
[ 191.637598] CPU: Processor Core ID: 1
[ 191.637605] Intel machine check architecture supported.
[ 191.637612] Intel machine check reporting enabled on CPU#1.
[ 191.637614] CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
[ 191.637618] CPU1: Thermal monitoring enabled
[ 191.638046] CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
[ 191.639026] Total of 2 processors activated (12793.34 BogoMIPS).
[ 191.639253] ENABLING IO-APIC IRQs
[ 191.639517] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 191.751654] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 191.771793] Brought up 2 CPUs
[ 191.772446] Booting paravirtualized kernel on bare hardware
[ 191.772772] NET: Registered protocol family 16
[ 191.773341] ACPI: bus type pci registered
[ 191.773632] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
[ 191.773710] PCI: Not using MMCONFIG.
[ 191.776230] PCI: Using configuration type 1
[ 191.776301] Setting up standard PCI resources
[ 191.787838] ACPI: Interpreter enabled
[ 191.787911] ACPI: (supports S0 S3 S4 S5)
[ 191.788241] ACPI: Using IOAPIC for interrupt routing
[ 191.798830] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 191.800144] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 191.800222] PCI quirk: region 0500-053f claimed by ICH6 GPIO
[ 191.802181] PCI: Transparent bridge - 0000:00:1e.0
[ 191.812928] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12)
[ 191.813621] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 191.814291] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12)
[ 191.814961] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 191.815639] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12)
[ 191.816309] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)
[ 191.816980] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 *10 11 12)
[ 191.817657] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[ 191.818524] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 191.818682] pnp: PnP ACPI init
[ 191.818776] ACPI: bus type pnp registered
[ 191.823159] pnp: PnP ACPI: found 13 devices
[ 191.823231] ACPI: ACPI bus type pnp unregistered
[ 191.823844] PCI: Using ACPI for IRQ routing
[ 191.823920] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 191.829531] NetLabel: Initializing
[ 191.829606] NetLabel: domain hash size = 128
[ 191.829676] NetLabel: protocols = UNLABELED CIPSOv4
[ 191.829779] NetLabel: unlabeled traffic allowed by default
[ 191.829912] ACPI: RTC can wake from S4
[ 191.830496] Time: tsc clocksource has been installed.
[ 191.832598] pnp: 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved
[ 191.832675] pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
[ 191.832752] pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 191.832828] pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 191.832916] pnp: 00:06: ioport range 0x500-0x53f has been reserved
[ 191.832992] pnp: 00:06: ioport range 0x400-0x47f has been reserved
[ 191.833067] pnp: 00:06: ioport range 0x680-0x6ff has been reserved
[ 191.833150] pnp: 00:07: iomem range 0xfed40000-0xfed44fff has been reserved
[ 191.864063] PCI: Bridge: 0000:00:1c.0
[ 191.864133] IO window: disabled.
[ 191.864206] MEM window: 52d00000-52dfffff
[ 191.864279] PREFETCH window: disabled.
[ 191.864353] PCI: Bridge: 0000:00:1c.1
[ 191.864423] IO window: 2000-2fff
[ 191.864496] MEM window: 52a00000-52afffff
[ 191.864574] PREFETCH window: disabled.
[ 191.864648] PCI: Bridge: 0000:00:1c.2
[ 191.864716] IO window: disabled.
[ 191.864789] MEM window: 52e00000-52efffff
[ 191.864862] PREFETCH window: disabled.
[ 191.864938] PCI: Bridge: 0000:04:00.0
[ 191.865007] IO window: disabled.
[ 191.865082] MEM window: 52000000-528fffff
[ 191.865156] PREFETCH window: 50000000-51ffffff
[ 191.865234] PCI: Bridge: 0000:00:1c.3
[ 191.865302] IO window: disabled.
[ 191.865375] MEM window: 52000000-528fffff
[ 191.865447] PREFETCH window: 50000000-51ffffff
[ 191.865527] PCI: Bridge: 0000:00:1c.4
[ 191.865596] IO window: disabled.
[ 191.865669] MEM window: 52f00000-52ffffff
[ 191.865741] PREFETCH window: disabled.
[ 191.865816] PCI: Bridge: 0000:00:1e.0
[ 191.865887] IO window: 1000-1fff
[ 191.865959] MEM window: 52900000-529fffff
[ 191.866032] PREFETCH window: 53000000-530fffff
[ 191.866135] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 191.866305] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
[ 191.866472] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 191.866646] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 191.866836] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
[ 191.867003] NET: Registered protocol family 2
[ 191.876576] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 191.876955] TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
[ 191.883752] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 191.890300] TCP: Hash tables configured (established 65536 bind 65536)
[ 191.890403] TCP reno registered
[ 191.892756] checking if image is initramfs...<6>Switched to high resolution mode on CPU 1
[ 192.120271] Switched to high resolution mode on CPU 0
[ 192.161400] it is
[ 192.459162] Freeing initrd memory: 7233k freed
[ 192.460119] Machine check exception polling timer started.
[ 192.460230] apm: BIOS not found.
[ 192.461117] audit: initializing netlink socket (disabled)
[ 192.461209] audit(1185214888.711:1): initialized
[ 192.461553] highmem bounce pool size: 64 pages
[ 192.461631] Total HugeTLB memory allocated, 0
[ 192.468607] VFS: Disk quotas dquot_6.5.1
[ 192.468814] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 192.469840] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 192.469941] io scheduler noop registered
[ 192.471750] io scheduler anticipatory registered
[ 192.471822] io scheduler deadline registered (default)
[ 192.471910] io scheduler cfq registered
[ 192.472669] assign_interrupt_mode Found MSI capability
[ 192.473137] assign_interrupt_mode Found MSI capability
[ 192.473599] assign_interrupt_mode Found MSI capability
[ 192.474072] assign_interrupt_mode Found MSI capability
[ 192.474523] assign_interrupt_mode Found MSI capability
[ 192.475278] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 192.475420] matroxfb: Matrox G550 detected
[ 192.476537] PInS memtype = 5
[ 192.477532] matroxfb: MTRR's turned on
[ 192.477650] matroxfb: 1280x1024x32bpp (virtual: 1280x3276)
[ 192.477724] matroxfb: framebuffer at 0x50000000, mapped to 0xf8880000, size 33554432
[ 192.478005] fbcon: MATROX (fb0) is primary device
[ 192.498714] Console: switching to colour frame buffer device 160x64
[ 192.506429] fb0: MATROX frame buffer device
[ 192.506642] matroxfb_crtc2: secondary head of fb0 was registered as fb1
[ 192.564340] Real Time Clock Driver v1.12ac
[ 192.564673] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 192.565889] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 195.574683] floppy0: no floppy controllers found
[ 195.576446] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
[ 195.576543] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 195.576619] Copyright (c) 1999-2006 Intel Corporation.
[ 195.576808] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 195.594347] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:03:d8:ff
[ 195.669735] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 195.670032] netconsole: device eth0 not up yet, forcing it
[ 197.300737] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 197.300834] e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO
[ 197.315401] console [netcon0] enabled
[ 198.446668] netconsole: network logging started
[ 198.451575] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 198.456213] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 198.461647] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 198.466767] mice: PS/2 mouse device common for all mice
[ 198.498362] input: AT Translated Set 2 keyboard as /class/input/input0
[ 198.503705] input: PC Speaker as /class/input/input1
[ 198.508785] NET: Registered protocol family 1
[ 198.513594] Starting balanced_irq
[ 198.518421] Using IPI No-Shortcut mode
[ 198.523888] Freeing unused kernel memory: 256k freed
[ 198.528639] Write protecting the kernel text: 2080k
[ 198.533323] Write protecting the kernel read-only data: 835k
[ 199.088098] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
>>> system on emergency shell prompt
>>> pressed ctrl/alt/del
[ 270.487595] md: stopping all md devices.
[-- Attachment #1.3: netconsole-2.6.23-rc1-noxen --]
[-- Type: text/plain, Size: 39773 bytes --]
[ 0.000000] Linux version 2.6.23-rc1-testing (ts@xenon) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #5 SMP PREEMPT Mon Jul 23 20:32:38 CEST 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003e584000 (usable)
[ 0.000000] BIOS-e820: 000000003e584000 - 000000003e591000 (reserved)
[ 0.000000] BIOS-e820: 000000003e591000 - 000000003e631000 (usable)
[ 0.000000] BIOS-e820: 000000003e631000 - 000000003e6a4000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003e6a4000 - 000000003e6a9000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003e6a9000 - 000000003e6f2000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003e6f2000 - 000000003e6ff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003e6ff000 - 000000003e700000 (usable)
[ 0.000000] BIOS-e820: 000000003e700000 - 000000003f000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] 103MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000fe200
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 255744
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 255744
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FE020, 0014 (r0 INTEL )
[ 0.000000] ACPI: RSDT 3E6FD038, 0054 (r1 INTEL DQ965GF 15DB 1000013)
[ 0.000000] ACPI: FACP 3E6FC000, 0074 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: DSDT 3E6F7000, 40E9 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: FACS 3E6AA000, 0040
[ 0.000000] ACPI: APIC 3E6F6000, 0078 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: WDDT 3E6F5000, 0040 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: MCFG 3E6F4000, 003C (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: ASF! 3E6F3000, 00A6 (r32 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: HPET 3E6F2000, 0038 (r1 INTEL DQ965GF 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A8000, 01BC (r1 INTEL CpuPm 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A7000, 0175 (r1 INTEL Cpu0Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A6000, 0175 (r1 INTEL Cpu1Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A5000, 0175 (r1 INTEL Cpu2Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: SSDT 3E6A4000, 0175 (r1 INTEL Cpu3Ist 15DB MSFT 1000013)
[ 0.000000] ACPI: TCPA 3E6A9000, 0A3F (r1 INTEL TIANO 2 MSFT 1000013)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:6 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f000000:c0e00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000008f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order. Total pages: 252248
[ 0.000000] Kernel command line: root=/dev/system/root video=matroxfb:vesa:0x31b resume=/dev/system/swap splash=verbose netconsole=6665@192.168.59.102/eth0,6666@192.168.59.127/00:50:da:82:a0:46
[ 0.000000] netconsole: local port 6665
[ 0.000000] netconsole: local IP 192.168.59.102
[ 0.000000] netconsole: interface eth0
[ 0.000000] netconsole: remote port 6666
[ 0.000000] netconsole: remote IP 192.168.59.127
[ 0.000000] netconsole: remote ethernet address 00:50:da:82:a0:46
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] CPU 0 irqstacks, hard=c044f000 soft=c0447000
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 3197.038 MHz processor.
[ 58.886774] Console: colour VGA+ 80x25
[ 58.886780] console [tty0] enabled
[ 58.892484] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 58.892575] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 58.892645] ... MAX_LOCK_DEPTH: 30
[ 58.892715] ... MAX_LOCKDEP_KEYS: 2048
[ 58.892784] ... CLASSHASH_SIZE: 1024
[ 58.892855] ... MAX_LOCKDEP_ENTRIES: 8192
[ 58.892925] ... MAX_LOCKDEP_CHAINS: 16384
[ 58.892995] ... CHAINHASH_SIZE: 8192
[ 58.893065] memory used by lock dependency info: 992 kB
[ 58.893137] per task-struct memory footprint: 1200 bytes
[ 58.893209] ------------------------
[ 58.893277] | Locking API testsuite:
[ 58.893346] ----------------------------------------------------------------------------
[ 58.893437] | spin |wlock |rlock |mutex | wsem | rsem |
[ 58.893529] --------------------------------------------------------------------------
[ 58.893626] A-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.894493] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.895353] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.896217] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok |
[ 58.897078] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.897959] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.898836] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok |
[ 58.899715] double unlock: ok | ok | ok | ok | ok | ok |
[ 58.900554] initialize held: ok | ok | ok | ok | ok | ok |
[ 58.901393] bad unlock order: ok | ok | ok | ok | ok | ok |
[ 58.902235] --------------------------------------------------------------------------
[ 58.902327] recursive read-lock: | ok | | ok |
[ 58.902793] recursive read-lock #2: | ok | | ok |
[ 58.903260] mixed read-write-lock: | ok | | ok |
[ 58.903728] mixed write-read-lock: | ok | | ok |
[ 58.904195] --------------------------------------------------------------------------
[ 58.904287] hard-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 58.904754] soft-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 58.905230] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 58.905704] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 58.906179] sirq-safe-A => hirqs-on/12: ok | ok | ok |
[ 58.906646] sirq-safe-A => hirqs-on/21: ok | ok | ok |
[ 58.907121] hard-safe-A + irqs-on/12: ok | ok | ok |
[ 58.907594] soft-safe-A + irqs-on/12: ok | ok | ok |
[ 58.908070] hard-safe-A + irqs-on/21: ok | ok | ok |
[ 58.908543] soft-safe-A + irqs-on/21: ok | ok | ok |
[ 58.909018] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 58.909500] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 58.909980] hard-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 58.910461] soft-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 58.910935] hard-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 58.911413] soft-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 58.911889] hard-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 58.912369] soft-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 58.912850] hard-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 58.913326] soft-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 58.913804] hard-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 58.914285] soft-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 58.914766] hard-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 58.915249] soft-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 58.915726] hard-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 58.916204] soft-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 58.916684] hard-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 58.917166] soft-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 58.917642] hard-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 58.918125] soft-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 58.918602] hard-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 58.919077] soft-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 58.919562] hard-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 58.920045] soft-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 58.920529] hard-irq lock-inversion/123: ok | ok | ok |
[ 58.921009] soft-irq lock-inversion/123: ok | ok | ok |
[ 58.921496] hard-irq lock-inversion/132: ok | ok | ok |
[ 58.921973] soft-irq lock-inversion/132: ok | ok | ok |
[ 58.922449] hard-irq lock-inversion/213: ok | ok | ok |
[ 58.922923] soft-irq lock-inversion/213: ok | ok | ok |
[ 58.923399] hard-irq lock-inversion/231: ok | ok | ok |
[ 58.923873] soft-irq lock-inversion/231: ok | ok | ok |
[ 58.924357] hard-irq lock-inversion/312: ok | ok | ok |
[ 58.924840] soft-irq lock-inversion/312: ok | ok | ok |
[ 58.927029] hard-irq lock-inversion/321: ok | ok | ok |
[ 58.927502] soft-irq lock-inversion/321: ok | ok | ok |
[ 58.927977] hard-irq read-recursion/123: ok |
[ 58.928217] soft-irq read-recursion/123: ok |
[ 58.928456] hard-irq read-recursion/132: ok |
[ 58.928695] soft-irq read-recursion/132: ok |
[ 58.928940] hard-irq read-recursion/213: ok |
[ 58.929183] soft-irq read-recursion/213: ok |
[ 58.929422] hard-irq read-recursion/231: ok |
[ 58.929661] soft-irq read-recursion/231: ok |
[ 58.929900] hard-irq read-recursion/312: ok |
[ 58.930138] soft-irq read-recursion/312: ok |
[ 58.930378] hard-irq read-recursion/321: ok |
[ 58.930616] soft-irq read-recursion/321: ok |
[ 58.930856] -------------------------------------------------------
[ 58.930930] Good, all 218 testcases passed! |
[ 58.931000] ---------------------------------
[ 58.931301] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 58.931755] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 58.959609] Memory: 993164k/1022976k available (2037k kernel code, 28096k reserved, 1041k data, 248k init, 104596k highmem)
[ 58.959715] virtual kernel memory layout:
[ 58.959716] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 58.959717] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 58.959718] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 58.959719] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 58.959721] .init : 0xc0406000 - 0xc0444000 ( 248 kB)
[ 58.959722] .data : 0xc02fd5b9 - 0xc0401ce4 (1041 kB)
[ 58.959723] .text : 0xc0100000 - 0xc02fd5b9 (2037 kB)
[ 58.960285] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 58.960467] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 58.960645] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 58.960905] hpet0: 3 64-bit timers, 14318180 Hz
[ 59.021938] Calibrating delay using timer specific routine.. 6399.59 BogoMIPS (lpj=3199798)
[ 59.022109] Security Framework v1.0.0 initialized
[ 59.022202] Mount-cache hash table entries: 512
[ 59.022675] monitor/mwait feature present.
[ 59.022745] using mwait in idle threads.
[ 59.022819] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 59.022950] CPU: L2 cache: 2048K
[ 59.023019] CPU: Physical Processor ID: 0
[ 59.023088] CPU: Processor Core ID: 0
[ 59.023166] Intel machine check architecture supported.
[ 59.023243] Intel machine check reporting enabled on CPU#0.
[ 59.023316] CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
[ 59.023391] CPU0: Thermal monitoring enabled
[ 59.023465] Compat vDSO mapped to ffffe000.
[ 59.023547] Checking 'hlt' instruction... OK.
[ 59.027250] lockdep: not fixing up alternatives.
[ 59.028437] ACPI: Core revision 20070126
[ 59.032167] CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
[ 59.032361] lockdep: not fixing up alternatives.
[ 59.032433] Booting processor 1/1 eip 3000
[ 59.032504] CPU 1 irqstacks, hard=c0450000 soft=c0448000
[ 59.043084] Initializing CPU#1
[ 59.102852] Calibrating delay using timer specific routine.. 6393.65 BogoMIPS (lpj=3196828)
[ 59.102867] monitor/mwait feature present.
[ 59.102873] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 59.102875] CPU: L2 cache: 2048K
[ 59.102877] CPU: Physical Processor ID: 0
[ 59.102879] CPU: Processor Core ID: 1
[ 59.102887] Intel machine check architecture supported.
[ 59.102894] Intel machine check reporting enabled on CPU#1.
[ 59.102896] CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
[ 59.102900] CPU1: Thermal monitoring enabled
[ 59.103339] CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04
[ 59.104317] Total of 2 processors activated (12793.25 BogoMIPS).
[ 59.104543] ENABLING IO-APIC IRQs
[ 59.104806] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 59.216935] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 59.237073] Brought up 2 CPUs
[ 59.237701] Booting paravirtualized kernel on bare hardware
[ 59.238018] NET: Registered protocol family 16
[ 59.238587] ACPI: bus type pci registered
[ 59.238880] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
[ 59.238958] PCI: Not using MMCONFIG.
[ 59.241469] PCI: Using configuration type 1
[ 59.241539] Setting up standard PCI resources
[ 59.253054] ACPI: Interpreter enabled
[ 59.253132] ACPI: (supports S0 S3 S4 S5)
[ 59.253460] ACPI: Using IOAPIC for interrupt routing
[ 59.263806] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 59.265110] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 59.265188] PCI quirk: region 0500-053f claimed by ICH6 GPIO
[ 59.267114] PCI: Transparent bridge - 0000:00:1e.0
[ 59.277888] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12)
[ 59.278561] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 59.279230] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12)
[ 59.279907] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 59.280574] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12)
[ 59.281243] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)
[ 59.281917] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 *10 11 12)
[ 59.282586] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[ 59.283463] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 59.283627] pnp: PnP ACPI init
[ 59.283718] ACPI: bus type pnp registered
[ 59.288107] pnp: PnP ACPI: found 13 devices
[ 59.288179] ACPI: ACPI bus type pnp unregistered
[ 59.288764] PCI: Using ACPI for IRQ routing
[ 59.288850] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 59.293883] NetLabel: Initializing
[ 59.293958] NetLabel: domain hash size = 128
[ 59.294028] NetLabel: protocols = UNLABELED CIPSOv4
[ 59.294132] NetLabel: unlabeled traffic allowed by default
[ 59.294261] ACPI: RTC can wake from S4
[ 59.294835] Time: tsc clocksource has been installed.
[ 59.296936] pnp: 00:01: iomem range 0xf0000000-0xf7ffffff has been reserved
[ 59.297013] pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
[ 59.297089] pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 59.297165] pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 59.297253] pnp: 00:06: ioport range 0x500-0x53f has been reserved
[ 59.297329] pnp: 00:06: ioport range 0x400-0x47f has been reserved
[ 59.297404] pnp: 00:06: ioport range 0x680-0x6ff has been reserved
[ 59.297487] pnp: 00:07: iomem range 0xfed40000-0xfed44fff has been reserved
[ 59.328405] PCI: Bridge: 0000:00:1c.0
[ 59.328475] IO window: disabled.
[ 59.328548] MEM window: 52d00000-52dfffff
[ 59.328620] PREFETCH window: disabled.
[ 59.328695] PCI: Bridge: 0000:00:1c.1
[ 59.328766] IO window: 2000-2fff
[ 59.328839] MEM window: 52a00000-52afffff
[ 59.328917] PREFETCH window: disabled.
[ 59.328991] PCI: Bridge: 0000:00:1c.2
[ 59.329059] IO window: disabled.
[ 59.329132] MEM window: 52e00000-52efffff
[ 59.329204] PREFETCH window: disabled.
[ 59.329279] PCI: Bridge: 0000:04:00.0
[ 59.329348] IO window: disabled.
[ 59.329422] MEM window: 52000000-528fffff
[ 59.329496] PREFETCH window: 50000000-51ffffff
[ 59.329573] PCI: Bridge: 0000:00:1c.3
[ 59.329641] IO window: disabled.
[ 59.329713] MEM window: 52000000-528fffff
[ 59.329786] PREFETCH window: 50000000-51ffffff
[ 59.329865] PCI: Bridge: 0000:00:1c.4
[ 59.329934] IO window: disabled.
[ 59.330006] MEM window: 52f00000-52ffffff
[ 59.330078] PREFETCH window: disabled.
[ 59.330153] PCI: Bridge: 0000:00:1e.0
[ 59.330224] IO window: 1000-1fff
[ 59.330296] MEM window: 52900000-529fffff
[ 59.330369] PREFETCH window: 53000000-530fffff
[ 59.330472] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 59.330639] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17
[ 59.330806] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 59.330979] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 59.331167] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
[ 59.331334] NET: Registered protocol family 2
[ 59.340916] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 59.341287] TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
[ 59.348077] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 59.354625] TCP: Hash tables configured (established 65536 bind 65536)
[ 59.354727] TCP reno registered
[ 59.357096] checking if image is initramfs...<6>Switched to high resolution mode on CPU 1
[ 59.585609] Switched to high resolution mode on CPU 0
[ 59.628967] it is
[ 59.928624] Freeing initrd memory: 7373k freed
[ 59.929585] Machine check exception polling timer started.
[ 59.929696] apm: BIOS not found.
[ 59.930565] audit: initializing netlink socket (disabled)
[ 59.930661] audit(1185216142.710:1): initialized
[ 59.931029] highmem bounce pool size: 64 pages
[ 59.931111] Total HugeTLB memory allocated, 0
[ 59.937880] VFS: Disk quotas dquot_6.5.1
[ 59.938091] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 59.939124] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 59.939226] io scheduler noop registered
[ 59.941044] io scheduler anticipatory registered
[ 59.941116] io scheduler deadline registered (default)
[ 59.941204] io scheduler cfq registered
[ 59.941967] assign_interrupt_mode Found MSI capability
[ 59.942438] assign_interrupt_mode Found MSI capability
[ 59.942892] assign_interrupt_mode Found MSI capability
[ 59.943350] assign_interrupt_mode Found MSI capability
[ 59.943824] assign_interrupt_mode Found MSI capability
[ 59.944583] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 59.944724] matroxfb: Matrox G550 detected
[ 59.945840] PInS memtype = 5
[ 59.946834] matroxfb: MTRR's turned on
[ 59.946948] matroxfb: 1280x1024x32bpp (virtual: 1280x3276)
[ 59.947022] matroxfb: framebuffer at 0x50000000, mapped to 0xf8880000, size 33554432
[ 59.947304] fbcon: MATROX (fb0) is primary device
[ 59.971891] Console: switching to colour frame buffer device 160x64
[ 59.979633] fb0: MATROX frame buffer device
[ 59.979845] matroxfb_crtc2: secondary head of fb0 was registered as fb1
[ 60.035897] Real Time Clock Driver v1.12ac
[ 60.036249] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 60.037532] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 63.045936] floppy0: no floppy controllers found
[ 63.047683] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
[ 63.047778] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 63.047861] Copyright (c) 1999-2006 Intel Corporation.
[ 63.048043] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 63.065610] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:19:d1:03:d8:ff
[ 63.139979] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 63.140312] netconsole: device eth0 not up yet, forcing it
[ 64.701024] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 64.701123] e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO
[ 64.715671] console [netcon0] enabled
[ 65.844897] netconsole: network logging started
[ 65.849710] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 65.854303] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 65.859544] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 65.864533] mice: PS/2 mouse device common for all mice
[ 65.894752] input: AT Translated Set 2 keyboard as /class/input/input0
[ 65.900014] input: PC Speaker as /class/input/input1
[ 65.905053] NET: Registered protocol family 1
[ 65.909826] Starting balanced_irq
[ 65.914596] Using IPI No-Shortcut mode
[ 65.920046] Freeing unused kernel memory: 248k freed
[ 65.924785] Write protecting the kernel text: 2040k
[ 65.929445] Write protecting the kernel read-only data: 813k
[ 66.488621] SCSI subsystem initialized
[ 66.512301] ACPI Exception (processor_throttling-0084): AE_NOT_FOUND, Evaluating _PTC [20070126]
[ 66.516877] ACPI Exception (processor_throttling-0147): AE_NOT_FOUND, Evaluating _TSS [20070126]
[ 66.521498] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 66.526081] ACPI Exception (processor_throttling-0084): AE_NOT_FOUND, Evaluating _PTC [20070126]
[ 66.530683] ACPI Exception (processor_throttling-0147): AE_NOT_FOUND, Evaluating _TSS [20070126]
[ 66.535265] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 66.539799] ACPI Exception (processor_core-0784): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 66.544419] ACPI Exception (processor_core-0784): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 66.582744] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 67.587416] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 67.592174] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part
[ 67.597500] scsi0 : ahci
[ 67.602563] scsi1 : ahci
[ 67.607434] scsi2 : ahci
[ 67.612231] scsi3 : ahci
[ 67.617004] scsi4 : ahci
[ 67.621764] scsi5 : ahci
[ 67.626401] ata1: SATA max UDMA/133 cmd 0xf883e100 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 67.631085] ata2: SATA max UDMA/133 cmd 0xf883e180 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 67.635754] ata3: SATA max UDMA/133 cmd 0xf883e200 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 67.640370] ata4: SATA max UDMA/133 cmd 0xf883e280 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 67.644910] ata5: SATA max UDMA/133 cmd 0xf883e300 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 67.649357] ata6: SATA max UDMA/133 cmd 0xf883e380 ctl 0x00000000 bmdma 0x00000000 irq 217
[ 68.108991] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 68.162613] ata1.00: ATA-7: ST380811AS, 3.AAE, max UDMA/133
[ 68.166915] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 68.220857] ata1.00: configured for UDMA/133
[ 68.680548] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 68.740538] ata2.00: ATA-7: ST380811AS, 3.AAE, max UDMA/133
[ 68.744780] ata2.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 68.798782] ata2.00: configured for UDMA/133
[ 69.105219] ata3: SATA link down (SStatus 0 SControl 300)
[ 69.411980] ata4: SATA link down (SStatus 0 SControl 300)
[ 69.718743] ata5: SATA link down (SStatus 0 SControl 300)
[ 70.025505] ata6: SATA link down (SStatus 0 SControl 300)
[ 70.029683] scsi 0:0:0:0: Direct-Access ATA ST380811AS 3.AA PQ: 0 ANSI: 5
[ 70.033909] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 70.037977] sd 0:0:0:0: [sda] Write Protect is off
[ 70.041979] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.046078] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 70.050095] sd 0:0:0:0: [sda] Write Protect is off
[ 70.054086] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.058143] sda: sda1 sda2
[ 70.087076] sd 0:0:0:0: [sda] Attached SCSI disk
[ 70.091432] scsi 1:0:0:0: Direct-Access ATA ST380811AS 3.AA PQ: 0 ANSI: 5
[ 70.102899] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 70.107233] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.111529] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.111653] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 70.120327] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 70.124695] sd 1:0:0:0: [sdb] Write Protect is off
[ 70.129127] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 70.133612] sdb: sdb1
[ 70.166129] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 70.170765] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 70.186723] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 70.194084] scsi6 : pata_marvell
[ 70.198917] scsi7 : pata_marvell
[ 70.203605] ata7: PATA max UDMA/100 cmd 0x00012018 ctl 0x00012026 bmdma 0x00012000 irq 16
[ 70.208337] ata8: DUMMY
[ 70.213091] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00
[ 70.677390] ata7.00: ATAPI: HL-DT-STDVD-ROM GDR8164B, 0L06, max UDMA/33
[ 70.682326] ata7.01: ATAPI: TSSTcorpCD/DVDW SH-S182M, SB03, max UDMA/33
[ 70.844255] ata7.00: configured for UDMA/33
[ 71.006128] ata7.01: configured for UDMA/33
[ 71.014456] scsi 6:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8164B 0L06 PQ: 0 ANSI: 5
[ 71.019580] scsi 6:0:0:0: Attached scsi generic sg2 type 5
[ 71.025657] scsi 6:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-S182M SB03 PQ: 0 ANSI: 5
[ 71.030760] scsi 6:0:1:0: Attached scsi generic sg3 type 5
[ 71.066861] ACPI: PCI Interrupt 0000:07:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 71.067621] sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 71.067626] Uniform CD-ROM driver Revision: 3.20
[ 71.090192] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 76.289672] scsi8 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 76.289675] <Adaptec 29160B Ultra160 SCSI adapter>
[ 76.289677] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 76.289679]
[ 76.333504] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 76.348013] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
[ 77.294697] kjournald starting. Commit interval 5 seconds
[ 77.300080] EXT3 FS on dm-1, internal journal
[ 77.305452] EXT3-fs: mounted filesystem with ordered data mode.
[ 79.132122] scsi 8:0:12:0: Sequential-Access HP C5683A C111 PQ: 0 ANSI: 2
[ 79.137150] target8:0:12: Beginning Domain Validation
[ 79.145556] target8:0:12: wide asynchronous
[ 79.152886] target8:0:12: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 32)
[ 79.159843] target8:0:12: Domain Validation skipping write tests
[ 79.164731] target8:0:12: Ending Domain Validation
[ 79.727519] parport_pc 00:08: reported by Plug and Play ACPI
[ 79.732367] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 79.819598] lp0: using parport0 (interrupt-driven).
[ 79.940015] scsi 8:0:12:0: Attached scsi generic sg4 type 1
[ 81.327007] st: Version 20070203, fixed bufsize 32768, s/g segs 256
[ 81.332109] st 8:0:12:0: Attached scsi tape st0
[ 81.337308] st 8:0:12:0: st0: try direct i/o: yes (alignment 512 B)
[ 81.393965] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 21 (level, low) -> IRQ 22
[ 81.486117] Linux agpgart interface v0.102
[ 81.542816] agpgart: Detected an Intel 965Q Chipset.
[ 81.548267] agpgart: Unknown page table size, assuming 512KB
[ 81.552923] agpgart: Detected 7676K stolen memory.
[ 81.614210] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 81.621657] rtc_cmos: probe of 00:03 failed with error -16
[ 81.629964] agpgart: AGP aperture is 256M @ 0x40000000
[ 81.696822] usbcore: registered new interface driver usbfs
[ 81.701493] usbcore: registered new interface driver hub
[ 81.706052] usbcore: registered new device driver usb
[ 81.855339] USB Universal Host Controller Interface driver v3.0
[ 81.859771] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 81.864175] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 81.869059] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 81.873409] uhci_hcd 0000:00:1a.0: irq 17, io base 0x000030c0
[ 81.878080] usb usb1: configuration #1 chosen from 1 choice
[ 81.882524] hub 1-0:1.0: USB hub found
[ 81.886983] hub 1-0:1.0: 2 ports detected
[ 81.992580] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 22
[ 81.997018] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 82.001418] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 82.005847] uhci_hcd 0000:00:1a.1: irq 22, io base 0x000030a0
[ 82.010452] usb usb2: configuration #1 chosen from 1 choice
[ 82.014880] hub 2-0:1.0: USB hub found
[ 82.019319] hub 2-0:1.0: 2 ports detected
[ 82.124344] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 82.128962] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 82.133622] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 82.138243] ehci_hcd 0000:00:1a.7: debug port 1
[ 82.142791] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x52c25c00
[ 82.151154] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 82.155858] usb usb3: configuration #1 chosen from 1 choice
[ 82.160461] hub 3-0:1.0: USB hub found
[ 82.164990] hub 3-0:1.0: 4 ports detected
[ 82.270225] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 82.274873] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 82.279496] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[ 82.284190] ehci_hcd 0000:00:1d.7: debug port 1
[ 82.288807] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x52c25800
[ 82.297274] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 82.302178] usb usb4: configuration #1 chosen from 1 choice
[ 82.306964] hub 4-0:1.0: USB hub found
[ 82.311719] hub 4-0:1.0: 6 ports detected
[ 82.417384] ACPI: PCI Interrupt 0000:07:03.0[A] -> <6>ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
[ 82.418020] GSI 19 (level, low) -> IRQ 19
[ 82.473878] firewire_ohci: Added fw-ohci device 0000:07:03.0, OHCI version 1.10
[ 82.478945] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 82.484032] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 82.489088] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 82.494101] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
[ 82.499312] usb usb5: configuration #1 chosen from 1 choice
[ 82.504312] hub 5-0:1.0: USB hub found
[ 82.509334] hub 5-0:1.0: 2 ports detected
[ 82.614954] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 82.620007] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 82.625021] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 82.630055] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
[ 82.635296] usb usb6: configuration #1 chosen from 1 choice
[ 82.640286] hub 6-0:1.0: USB hub found
[ 82.645193] hub 6-0:1.0: 2 ports detected
[ 82.750809] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 82.755796] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 82.760823] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 82.765845] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[ 82.771136] usb usb7: configuration #1 chosen from 1 choice
[ 82.776178] hub 7-0:1.0: USB hub found
[ 82.781192] hub 7-0:1.0: 2 ports detected
[ 82.960588] usb 6-2: new low speed USB device using uhci_hcd and address 2
[ 82.973657] firewire_core: created new fw device fw0 (0 config rom retries, S400)
[ 83.107819] usb 6-2: configuration #1 chosen from 1 choice
[ 83.153137] Adding 2097144k swap on /dev/system/swap. Priority:-1 extents:1 across:2097144k
[ 83.212703] usbcore: registered new interface driver hiddev
[ 83.230753] input: HID 413c:3010 as /class/input/input2
[ 83.236114] input: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:1d.1-2
[ 83.241418] usbcore: registered new interface driver usbhid
[ 83.246605] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 85.723579] loop: module loaded
[ 85.758246] kjournald starting. Commit interval 5 seconds
[ 85.762515] EXT3 FS on sda1, internal journal
[ 85.766811] EXT3-fs: mounted filesystem with ordered data mode.
[ 85.796700] kjournald starting. Commit interval 5 seconds
[ 85.801007] EXT3 FS on dm-0, internal journal
[ 85.805281] EXT3-fs: mounted filesystem with ordered data mode.
[ 85.841373] kjournald starting. Commit interval 5 seconds
[ 85.845612] EXT3 FS on dm-3, internal journal
[ 85.849868] EXT3-fs: mounted filesystem with ordered data mode.
[ 85.884307] kjournald starting. Commit interval 5 seconds
[ 85.888492] EXT3 FS on dm-4, internal journal
[ 85.892656] EXT3-fs: mounted filesystem with ordered data mode.
[ 92.713025] NET: Registered protocol family 10
[ 92.717020] lo: Disabled Privacy Extensions
[ 92.763977] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 92.907350] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 92.951804] Netfilter messages via NETLINK v0.30.
[ 92.985157] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 94.287332] input: Power Button (FF) as /class/input/input3
[ 94.291527] ACPI: Power Button (FF) [PWRF]
[ 94.300217] input: Sleep Button (CM) as /class/input/input4
[ 94.308606] ACPI: Sleep Button (CM) [SLPB]
[ 95.829804] powernow: This module only works with AMD K7 CPUs
[ 97.574723] audit(1185216181.484:2): audit_pid=5086 old=0 by auid=4294967295
[ 98.316460] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[ 99.133241] BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 99.133456] printing eip:
[ 99.133581] f886ab15
[ 99.133699] *pde = 00000000
[ 99.133822] Oops: 0000 [#1]
[ 99.133944] PREEMPT SMP
[ 99.134111] Modules linked in: snd_mixer_oss snd_seq snd_seq_device cpufreq_conservative cpufreq_ondemand cpufreq_userspace cpufreq_powersave acpi_cpufreq speedstep_lib freq_table button battery ac ip6t_REJECT xt_tcpudp ipt_REJECT xt_state iptable_mangle iptable_nat nf_nat iptable_filter ip6table_mangle nf_conntrack_ipv4 nf_conntrack nfnetlink ip_tables ip6table_filter ip6_tables x_tables ipv6 loop usbhid snd_hda_intel firewire_ohci ehci_hcd uhci_hcd firewire_core snd_pcm usbcore rtc_cmos crc_itu_t intel_agp rtc_core agpgart snd_timer i2c_i801 st snd i2c_core rtc_lib soundcore snd_page_alloc parport_pc lp parport ext3 mbcache jbd dm_snapshot edd dm_mod fan aic7xxx sr_mod cdrom scsi_transport_spi pata_marvell sg ahci libata thermal processor sd_mod scsi_mod
[ 99.136884] CPU: 1
[ 99.136885] EIP: 0060:[<f886ab15>] Not tainted VLI
[ 99.136886] EFLAGS: 00010293 (2.6.23-rc1-testing #5)
[ 99.137307] EIP is at acpi_processor_throttling_seq_show+0x98/0xe4 [processor]
[ 99.137466] eax: 00000000 ebx: fffffffb ecx: 00000000 edx: 00000000
[ 99.137618] esi: f7a97c00 edi: 00000000 ebp: f71b1f0c esp: f71b1ee0
[ 99.137777] ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
[ 99.137929] Process powersaved (pid: 5162, ti=f71b1000 task=f71b0000 task.ti=f71b1000)
[ 99.138025] Stack: f7275900 f886d5aa 00000008 00000000 00000000 00000007 00000000 f7275900
[ 99.138402] fffffffb f7275900 00000001 f71b1f4c c0194865 00000400 b7f58000 f71d2600
[ 99.138785] f7275920 00000000 dfe9f898 00000001 00000246 dfe9f898 00000000 00000000
[ 99.139177] Call Trace:
[ 99.139378] [<c0105244>] show_trace_log_lvl+0x1a/0x2f
[ 99.139553] [<c01052f6>] show_stack_log_lvl+0x9d/0xa5
[ 99.139717] [<c01054ef>] show_registers+0x1f1/0x332
[ 99.139877] [<c010574b>] die+0x11b/0x250
[ 99.140037] [<c02fba0e>] do_page_fault+0x512/0x5e3
[ 99.140200] [<c02fa07a>] error_code+0x72/0x78
[ 99.140356] [<c0194865>] seq_read+0xef/0x266
[ 99.140522] [<c01abf29>] proc_reg_read+0x63/0x76
[ 99.140682] [<c017dc34>] vfs_read+0xad/0x136
[ 99.140838] [<c017e065>] sys_read+0x3d/0x61
[ 99.141002] [<c010411a>] sysenter_past_esp+0x6b/0xb5
[ 99.141176] =======================
[ 99.141301] Code: 45 f0 89 04 24 e8 8a 98 92 c7 ba 00 d6 86 f8 8b 45 f0 e8 60 96 92 c7 31 ff c7 45 ec 00 00 00 00 eb 43 8b 86 04 03 00 00 8b 55 ec <8b> 0c 02 ba 2a 00 00 00 3b be d8 02 00 00 b8 20 00 00 00 0f 45
[ 99.143171] EIP: [<f886ab15>] acpi_processor_throttling_seq_show+0x98/0xe4 [processor] SS:ESP 0068:f71b1ee0
>>> system up
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 19:42 ` Tilman Schmidt
@ 2007-07-23 20:32 ` Jeremy Fitzhardinge
2007-07-23 23:02 ` Tilman Schmidt
0 siblings, 1 reply; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-23 20:32 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, andi, nix.or.die, Roland McGrath
Tilman Schmidt wrote:
> To answer that, I have reproduced the effect with kernel 2.6.23-rc1 with
> netconsole compiled in. I'm attaching both captures, for CONFIG_XEN=y
> (unsuccessful) as well CONFIG_XEN=n (successful).
>
> The first noticeable difference is that the nonzero timestamps starting
> after the line "Detected 3197.059 MHz processor" are much bigger with XEN -
> but perhaps that's expected.
>
Not at all. None of the Xen time machinery should be coming into play.
> More to the point, everything from:
>
> SCSI subsystem initialized
>
> on is completely missing, including all the [S/P]ATA, SCSI, parport, AGP,
> USB, Firewire, RTC and of course ext3 messages. Only the "device-mapper"
> line still appears.
I'm flat out confused. The only CONFIG_XEN dependencies in the kernel are:
1. head.S and entry.S, which enable completely no-op pieces of code
when not running under Xen
2. The vdso code, which shouldn't play a role here
3. The whole of arch/i386/xen/, which doesn't get enabled unless you
run under Xen
There's flat out no way that your kernel would be booting if any of the
Xen code were actually being run, since it would fall over very quickly
without the hypervisor being present. And anyway, the message "Booting
paravirtualized kernel on bare hardware" tells us we're not using the
Xen code.
How much of this is modules? Is the initrd probing for scsi/sata?
Maybe the the vdso change is having an effect.
Ooh, wait. Do you have an old version of the Xen patches in place,
perhaps? Does drivers/block/Makefile have:
obj-$(CONFIG_XEN_BLKDEV_FRONTEND) += xen-blkfront.o
(vs := xen-blkfront.o) Not that it should have any effect on scsi drivers.
Could you do a before and after booting with initcall_debug=1?
Thanks,
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 20:32 ` Jeremy Fitzhardinge
@ 2007-07-23 23:02 ` Tilman Schmidt
2007-07-24 0:14 ` Jeremy Fitzhardinge
2007-07-24 3:46 ` Jeremy Fitzhardinge
0 siblings, 2 replies; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-23 23:02 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: LKML, andi, nix.or.die, Roland McGrath
[-- Attachment #1: Type: text/plain, Size: 1633 bytes --]
Am 23.07.2007 22:32 schrieb Jeremy Fitzhardinge:
> How much of this is modules? Is the initrd probing for scsi/sata?
> Maybe the the vdso change is having an effect.
Pretty much all of it is modules. The base system is openSUSE 10.2, and
SuSE has a long habit of building everything as modules and putting the
drivers needed for accessing the root filesystem into an initrd. I have
fought it for a while but nowadays I'm playing along.
So yes, all of ahci, pata_marvell, aic7xxx, jbd, dm_mod, ext3 are in
fact modules in initrd. Would it help to try a kernel with some or all
of these built in?
> Ooh, wait. Do you have an old version of the Xen patches in place,
> perhaps?
In which place? I installed and successfully ran the Xen packages that
came with openSUSE 10.2, so there is a 2.6.18 kernel with SuSE's Xen
patches on the machine. But that shouldn't have any influence on the
kernel.org kernels I build myself, should it?
> Does drivers/block/Makefile have:
>
> obj-$(CONFIG_XEN_BLKDEV_FRONTEND) += xen-blkfront.o
>
> (vs := xen-blkfront.o)
It has the "+=" variant.
> Could you do a before and after booting with initcall_debug=1?
"Before" and "after" meaning with CONFIG_XEN=n and CONFIG_XEN=y, I
suppose. The resulting logs are a bit biggish, so I have put them on
http://www.phnxsoft.com/~ts/linux/ for download. Let me know if you
prefer having them mailed.
HTH
T.
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 23:02 ` Tilman Schmidt
@ 2007-07-24 0:14 ` Jeremy Fitzhardinge
2007-07-24 8:51 ` Tilman Schmidt
2007-07-24 9:10 ` Andi Kleen
2007-07-24 3:46 ` Jeremy Fitzhardinge
1 sibling, 2 replies; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 0:14 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, andi, nix.or.die
Tilman Schmidt wrote:
> Am 23.07.2007 22:32 schrieb Jeremy Fitzhardinge:
>
>> How much of this is modules? Is the initrd probing for scsi/sata?
>> Maybe the the vdso change is having an effect.
>>
>
> Pretty much all of it is modules. The base system is openSUSE 10.2, and
> SuSE has a long habit of building everything as modules and putting the
> drivers needed for accessing the root filesystem into an initrd. I have
> fought it for a while but nowadays I'm playing along.
>
> So yes, all of ahci, pata_marvell, aic7xxx, jbd, dm_mod, ext3 are in
> fact modules in initrd. Would it help to try a kernel with some or all
> of these built in?
>
>
>> Ooh, wait. Do you have an old version of the Xen patches in place,
>> perhaps?
>>
>
> In which place? I installed and successfully ran the Xen packages that
> came with openSUSE 10.2, so there is a 2.6.18 kernel with SuSE's Xen
> patches on the machine. But that shouldn't have any influence on the
> kernel.org kernels I build myself, should it?
>
>
>> Does drivers/block/Makefile have:
>>
>> obj-$(CONFIG_XEN_BLKDEV_FRONTEND) += xen-blkfront.o
>>
>> (vs := xen-blkfront.o)
>>
>
> It has the "+=" variant.
>
>
>> Could you do a before and after booting with initcall_debug=1?
>>
>
> "Before" and "after" meaning with CONFIG_XEN=n and CONFIG_XEN=y, I
> suppose. The resulting logs are a bit biggish, so I have put them on
> http://www.phnxsoft.com/~ts/linux/ for download. Let me know if you
> prefer having them mailed.
Well, it looks to me like it all falls over once it hits usermode;
everything up till then is identical (except for the Xen-related
initcalls which naturally don't exist in the non-Xen case).
I'm at a loss. I don't know if there's some way to debug the initrd in
more detail. I suspect that its failing all PCI probing, rather being a
specific SCSI/AHCI problem (since none of the other messages appear either).
Does the Xen case just hang, or reboot, or what? The kernel messages
just appear to stop. I'd expect it to at least complain about not
mounting the root filesystem or something.
Andi, any thoughts about how to debug the suse boot sequence?
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-23 23:02 ` Tilman Schmidt
2007-07-24 0:14 ` Jeremy Fitzhardinge
@ 2007-07-24 3:46 ` Jeremy Fitzhardinge
1 sibling, 0 replies; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 3:46 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, andi, nix.or.die, Roland McGrath
Tilman Schmidt wrote:
> So yes, all of ahci, pata_marvell, aic7xxx, jbd, dm_mod, ext3 are in
> fact modules in initrd. Would it help to try a kernel with some or all
> of these built in?
>
Yes, that would be useful. It would help tell whether its a module
loading problem or a basic pci probing problem.
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 0:14 ` Jeremy Fitzhardinge
@ 2007-07-24 8:51 ` Tilman Schmidt
2007-07-24 8:59 ` Jeremy Fitzhardinge
2007-07-24 9:10 ` Andi Kleen
1 sibling, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-24 8:51 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: LKML, andi, nix.or.die
[-- Attachment #1: Type: text/plain, Size: 1469 bytes --]
Jeremy Fitzhardinge schrieb:
> Well, it looks to me like it all falls over once it hits usermode;
> everything up till then is identical (except for the Xen-related
> initcalls which naturally don't exist in the non-Xen case).
Just a wild thought: could the actual problem be with accessing the
initrd? After all, everything that's failing is based on modules
which are stuffed there. But I know far too less about initrd to
pursue this thought further.
> I'm at a loss. I don't know if there's some way to debug the initrd in
> more detail. I suspect that its failing all PCI probing, rather being a
> specific SCSI/AHCI problem (since none of the other messages appear either).
>
> Does the Xen case just hang, or reboot, or what? The kernel messages
> just appear to stop. I'd expect it to at least complain about not
> mounting the root filesystem or something.
Yes, of course. Sorry, I thought I'd mentioned that. It shows the
standard behaviour of a Suse that cannot mount its root filesystem:
first a message: "waiting for /dev/system/root to appear" followed
by a series of dots, and then fallback into a standalone /bin/sh.
> Andi, any thoughts about how to debug the suse boot sequence?
>
> J
<listening eagerly>
T.
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 250 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 8:51 ` Tilman Schmidt
@ 2007-07-24 8:59 ` Jeremy Fitzhardinge
0 siblings, 0 replies; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 8:59 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: LKML, andi, nix.or.die
Tilman Schmidt wrote:
> Jeremy Fitzhardinge schrieb:
>
>> Well, it looks to me like it all falls over once it hits usermode;
>> everything up till then is identical (except for the Xen-related
>> initcalls which naturally don't exist in the non-Xen case).
>>
>
> Just a wild thought: could the actual problem be with accessing the
> initrd? After all, everything that's failing is based on modules
> which are stuffed there. But I know far too less about initrd to
> pursue this thought further.
>
Well, the kernel is managing to mount the initrd as a filesystem, and
the "waiting for root to appear" message looks like its coming from
usermode as well. So I suspect its something to do with module loading,
but I can't imagine what at the moment.
Statically compiling the scsi/ahci/etc drivers will help make some
progress in debugging this.
I really can't see how its directly Xen related. It looks like either:
1. some bug which only appears with particular kernel memory layouts,
and enabling Xen happens to make it bad
2. or some kind of linker bug, possibly triggered by Xen's ELF notes
(but I'd really expect this to break in a more basic way)
3. ...?
>> I'm at a loss. I don't know if there's some way to debug the initrd in
>> more detail. I suspect that its failing all PCI probing, rather being a
>> specific SCSI/AHCI problem (since none of the other messages appear either).
>>
>> Does the Xen case just hang, or reboot, or what? The kernel messages
>> just appear to stop. I'd expect it to at least complain about not
>> mounting the root filesystem or something.
>>
>
> Yes, of course. Sorry, I thought I'd mentioned that. It shows the
> standard behaviour of a Suse that cannot mount its root filesystem:
> first a message: "waiting for /dev/system/root to appear" followed
> by a series of dots, and then fallback into a standalone /bin/sh.
>
Oh, you get a shell? What does /proc/pci have in it? What happens if
you manually try to modprobe something? That gives us much more to work
with.
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 0:14 ` Jeremy Fitzhardinge
2007-07-24 8:51 ` Tilman Schmidt
@ 2007-07-24 9:10 ` Andi Kleen
2007-07-24 9:56 ` Olaf Hering
1 sibling, 1 reply; 27+ messages in thread
From: Andi Kleen @ 2007-07-24 9:10 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: Tilman Schmidt, LKML, andi, nix.or.die, olh
On Mon, Jul 23, 2007 at 05:14:05PM -0700, Jeremy Fitzhardinge wrote:
> Well, it looks to me like it all falls over once it hits usermode;
> everything up till then is identical (except for the Xen-related
> initcalls which naturally don't exist in the non-Xen case).
>
> I'm at a loss. I don't know if there's some way to debug the initrd in
> more detail. I suspect that its failing all PCI probing, rather being a
> specific SCSI/AHCI problem (since none of the other messages appear either).
>
> Does the Xen case just hang, or reboot, or what? The kernel messages
> just appear to stop. I'd expect it to at least complain about not
> mounting the root filesystem or something.
>
> Andi, any thoughts about how to debug the suse boot sequence?
Hmm, you could add a set -x into the startup script /sbin/mkinitrd
generates. But some work also happens with udev in the background.
Or let's ask Olaf, he's the expert on that
-Andi
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 9:10 ` Andi Kleen
@ 2007-07-24 9:56 ` Olaf Hering
2007-07-24 10:36 ` Tilman Schmidt
2007-07-24 18:08 ` Tilman Schmidt
0 siblings, 2 replies; 27+ messages in thread
From: Olaf Hering @ 2007-07-24 9:56 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: Tilman Schmidt, LKML, nix.or.die, andi
On Tue, Jul 24, Andi Kleen wrote:
> > Andi, any thoughts about how to debug the suse boot sequence?
The SuSE boot sequence is rather long. Which part (and which version) are we talking about?
As Andi said, putting a 'set -x' into /init script generated by /sbin/mkinitrd
is one thing. You can also boot with 'linuxrc=trace' to generate a huge
amount of udev and /init debug.
Booting with 'confirm' will allow you to step each runlevel script, see
/etc/init.d/boot, look for DO_CONFIRM=.
My Email provider kicked me off of lkml, so I dont have the rest of this
thread at hand.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 9:56 ` Olaf Hering
@ 2007-07-24 10:36 ` Tilman Schmidt
2007-07-24 13:45 ` Olaf Hering
2007-07-24 18:08 ` Tilman Schmidt
1 sibling, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-24 10:36 UTC (permalink / raw)
To: Olaf Hering; +Cc: Jeremy Fitzhardinge, LKML, nix.or.die, andi
[-- Attachment #1: Type: text/plain, Size: 1596 bytes --]
Olaf Hering schrieb:
> On Tue, Jul 24, Andi Kleen wrote:
>
>> > Andi, any thoughts about how to debug the suse boot sequence?
>
> The SuSE boot sequence is rather long. Which part (and which version) are we talking about?
Quick summary of the problem:
Opensuse 10.2 32-bit install on a Pentium D 940
Kernel 2.6.22-git17 or later (last reproduced with 2.6.23-rc1)
A kernel built with CONFIG_XEN=y fails to detect the SATA disks during
boot, so the root filesystem cannot be mounted and I'm thrown into
the emergency /bin/sh. With CONFIG_XEN=n everything works fine.
Netconsole logs with initcall_debug=1 of a successful and a
failing startup and corresponding .config-s are available at
http://www.phnxsoft.com/~ts/linux/
> As Andi said, putting a 'set -x' into /init script generated by /sbin/mkinitrd
> is one thing.
I'll try. I guess I'll have to unpack/repack the finished initrd
image (gzipped cpio archive, AFAICS) for that - or is there a way
to have mkinitrd inject that statement for me?
> You can also boot with 'linuxrc=trace' to generate a huge
> amount of udev and /init debug.
That looks simple enough, so I'll try that first, although it looks
to me like the trouble happens before udev comes into play.
> Booting with 'confirm' will allow you to step each runlevel script, see
> /etc/init.d/boot, look for DO_CONFIRM=.
Thanks,
Tilman
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 250 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 10:36 ` Tilman Schmidt
@ 2007-07-24 13:45 ` Olaf Hering
2007-07-24 15:45 ` Jeremy Fitzhardinge
0 siblings, 1 reply; 27+ messages in thread
From: Olaf Hering @ 2007-07-24 13:45 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: Jeremy Fitzhardinge, LKML, nix.or.die, andi
On Tue, Jul 24, Tilman Schmidt wrote:
> Netconsole logs with initcall_debug=1 of a successful and a
> failing startup and corresponding .config-s are available at
> http://www.phnxsoft.com/~ts/linux/
It seems the modules are not loaded at all in initrd, I dont see the
'SCSI subsystem initialized' message for example.
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 13:45 ` Olaf Hering
@ 2007-07-24 15:45 ` Jeremy Fitzhardinge
2007-07-24 15:47 ` Andi Kleen
0 siblings, 1 reply; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 15:45 UTC (permalink / raw)
To: Olaf Hering; +Cc: Tilman Schmidt, LKML, nix.or.die, andi
Olaf Hering wrote:
> It seems the modules are not loaded at all in initrd, I dont see the
> 'SCSI subsystem initialized' message for example.
Yes. It's not clear to me whether that's because module loading is
failing for some reason, or pci bus probing. And completely unclear to
me why CONFIG_XEN should make a difference.
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 15:45 ` Jeremy Fitzhardinge
@ 2007-07-24 15:47 ` Andi Kleen
0 siblings, 0 replies; 27+ messages in thread
From: Andi Kleen @ 2007-07-24 15:47 UTC (permalink / raw)
To: Jeremy Fitzhardinge; +Cc: Olaf Hering, Tilman Schmidt, LKML, nix.or.die, andi
On Tue, Jul 24, 2007 at 08:45:09AM -0700, Jeremy Fitzhardinge wrote:
> Olaf Hering wrote:
> > It seems the modules are not loaded at all in initrd, I dont see the
> > 'SCSI subsystem initialized' message for example.
>
> Yes. It's not clear to me whether that's because module loading is
> failing for some reason, or pci bus probing. And completely unclear to
> me why CONFIG_XEN should make a difference.
Tilman can you double check you did make modules_install / mkinitrd
properly and that mkinitrd uses the correct modules?
-Andi
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 9:56 ` Olaf Hering
2007-07-24 10:36 ` Tilman Schmidt
@ 2007-07-24 18:08 ` Tilman Schmidt
2007-07-24 19:02 ` Jeremy Fitzhardinge
1 sibling, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-24 18:08 UTC (permalink / raw)
To: Olaf Hering; +Cc: Jeremy Fitzhardinge, LKML, Gabriel C, Andi Kleen
[-- Attachment #1: Type: text/plain, Size: 2196 bytes --]
Alright, I know what's going on now, and it looks like a problem with
the Opensuse init script. In fact, the initrd for the Xen enabled
kernel got a *different* init script than the one for the non-Xen one.
The difference being:
--- /tmp/testing/init 2007-07-24 15:53:58.000000000 +0200
+++ /tmp/xentest/init 2007-07-24 15:54:16.000000000 +0200
@@ -308,6 +308,9 @@
fi
fi
+caps="$(</proc/xen/capabilities)"
+if [ "$caps" != "${caps%control_d*}" ]; then
+
params=
for p in $(cat /proc/cmdline) ; do
case $p in
@@ -509,6 +512,32 @@
echo "Loading dm-snapshot"
modprobe dm-snapshot $params
+else
+
+params=
+for p in $(cat /proc/cmdline) ; do
+ case $p in
+ dm-mod.*)
+ params="$params ${p#dm-mod.}"
+ ;;
+ esac
+done
+echo "Loading dm-mod"
+modprobe dm-mod $params
+
+params=
+for p in $(cat /proc/cmdline) ; do
+ case $p in
+ dm-snapshot.*)
+ params="$params ${p#dm-snapshot.}"
+ ;;
+ esac
+done
+echo "Loading dm-snapshot"
+modprobe dm-snapshot $params
+
+fi
+
echo -n "Waiting for /dev/mapper/control to appear: "
for i in 1 2 3 4 5; do
[ -e /dev/mapper/control ] && break
In clear: the Xen init script reads /proc/xen/capabilities and if it
doesn't find the magic string "control_d" in it, willfully *skips*
loading all the SCSI and ATA stuff.
The missing piece then is the innocent little line:
/init: line 311: /proc/xen/capabilities: No such file or directory
appearing on my screen during boot ... BOOM!
If I just diligently type all the skipped modprobe commands
$ modprobe scsi_mod
$ modprobe sd_mod
$ modprobe processor
$ modprobe thermal
$ modprobe libata
$ modprobe ahci
$ modprobe pata_marvell
$ modprobe scsi_transport_spi
$ modprobe aic7xxx
$ modprobe fan
$ modprobe edd
$ ^D
into the fallback shell by hand, the system comes up without further ado.
So there, case solved. Now you sort it out who's to fix what. :-)
Thanks,
Tilman
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 18:08 ` Tilman Schmidt
@ 2007-07-24 19:02 ` Jeremy Fitzhardinge
2007-07-24 19:12 ` Andi Kleen
0 siblings, 1 reply; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 19:02 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: Olaf Hering, LKML, Gabriel C, Andi Kleen
Tilman Schmidt wrote:
> Alright, I know what's going on now, and it looks like a problem with
> the Opensuse init script. In fact, the initrd for the Xen enabled
> kernel got a *different* init script than the one for the non-Xen one.
> The difference being:
>
Phew, I was getting worried there for a minute. Does the install script
check for CONFIG_XEN in the kernel config or something?
> --- /tmp/testing/init 2007-07-24 15:53:58.000000000 +0200
> +++ /tmp/xentest/init 2007-07-24 15:54:16.000000000 +0200
> @@ -308,6 +308,9 @@
> fi
> fi
>
> +caps="$(</proc/xen/capabilities)"
> +if [ "$caps" != "${caps%control_d*}" ]; then
> +
> params=
> for p in $(cat /proc/cmdline) ; do
> case $p in
> @@ -509,6 +512,32 @@
> echo "Loading dm-snapshot"
> modprobe dm-snapshot $params
>
> +else
> +
> +params=
> +for p in $(cat /proc/cmdline) ; do
> + case $p in
> + dm-mod.*)
> + params="$params ${p#dm-mod.}"
> + ;;
> + esac
> +done
> +echo "Loading dm-mod"
> +modprobe dm-mod $params
> +
> +params=
> +for p in $(cat /proc/cmdline) ; do
> + case $p in
> + dm-snapshot.*)
> + params="$params ${p#dm-snapshot.}"
> + ;;
> + esac
> +done
> +echo "Loading dm-snapshot"
> +modprobe dm-snapshot $params
> +
> +fi
> +
> echo -n "Waiting for /dev/mapper/control to appear: "
> for i in 1 2 3 4 5; do
> [ -e /dev/mapper/control ] && break
>
> In clear: the Xen init script reads /proc/xen/capabilities and if it
> doesn't find the magic string "control_d" in it, willfully *skips*
> loading all the SCSI and ATA stuff.
>
> The missing piece then is the innocent little line:
>
> /init: line 311: /proc/xen/capabilities: No such file or directory
>
> appearing on my screen during boot ... BOOM!
>
> If I just diligently type all the skipped modprobe commands
>
> $ modprobe scsi_mod
> $ modprobe sd_mod
> $ modprobe processor
> $ modprobe thermal
> $ modprobe libata
> $ modprobe ahci
> $ modprobe pata_marvell
> $ modprobe scsi_transport_spi
> $ modprobe aic7xxx
> $ modprobe fan
> $ modprobe edd
> $ ^D
>
> into the fallback shell by hand, the system comes up without further ado.
>
> So there, case solved. Now you sort it out who's to fix what. :-)
>
Well, definitely on the suse side. I don't think there's any point in
me renaming CONFIG_XEN to something less obvious to avoid this
breakage. I guess the proper fix is to carry on as if its a native boot
if /proc/xen/* is missing, since they'll never be there when not booting
under Xen (and unlikely to be there in a paravirt-xen boot anyway).
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 19:02 ` Jeremy Fitzhardinge
@ 2007-07-24 19:12 ` Andi Kleen
2007-07-24 19:15 ` Jeremy Fitzhardinge
2007-07-24 20:48 ` Tilman Schmidt
0 siblings, 2 replies; 27+ messages in thread
From: Andi Kleen @ 2007-07-24 19:12 UTC (permalink / raw)
To: Jeremy Fitzhardinge
Cc: Tilman Schmidt, Olaf Hering, LKML, Gabriel C, Andi Kleen
On Tue, Jul 24, 2007 at 12:02:45PM -0700, Jeremy Fitzhardinge wrote:
> Tilman Schmidt wrote:
> > Alright, I know what's going on now, and it looks like a problem with
> > the Opensuse init script. In fact, the initrd for the Xen enabled
> > kernel got a *different* init script than the one for the non-Xen one.
> > The difference being:
> >
>
> Phew, I was getting worried there for a minute. Does the install script
> check for CONFIG_XEN in the kernel config or something?
Yes 10.2 mkinitrd does. But it still should work because a dom0
kernel would obviously need all the drivers. A paravirt ops
kernel native is like a dom0 variant.
http://firstfloor.org/~andi/mkinitrd
-Andi
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 19:12 ` Andi Kleen
@ 2007-07-24 19:15 ` Jeremy Fitzhardinge
2007-07-24 20:48 ` Tilman Schmidt
1 sibling, 0 replies; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 19:15 UTC (permalink / raw)
To: Andi Kleen; +Cc: Tilman Schmidt, Olaf Hering, LKML, Gabriel C
Andi Kleen wrote:
> Yes 10.2 mkinitrd does. But it still should work because a dom0
> kernel would obviously need all the drivers. A paravirt ops
> kernel native is like a dom0 variant.
>
> http://firstfloor.org/~andi/mkinitrd
Well, it appears to be assuming that a dom0 Xen kernel will have stuff
in /proc/xen/.
J
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 19:12 ` Andi Kleen
2007-07-24 19:15 ` Jeremy Fitzhardinge
@ 2007-07-24 20:48 ` Tilman Schmidt
2007-07-24 21:20 ` Jeremy Fitzhardinge
1 sibling, 1 reply; 27+ messages in thread
From: Tilman Schmidt @ 2007-07-24 20:48 UTC (permalink / raw)
To: Andi Kleen; +Cc: Jeremy Fitzhardinge, Olaf Hering, LKML, Gabriel C
[-- Attachment #1: Type: text/plain, Size: 2444 bytes --]
Am 24.07.2007 21:12 schrieb Andi Kleen:
> On Tue, Jul 24, 2007 at 12:02:45PM -0700, Jeremy Fitzhardinge wrote:
>> Phew, I was getting worried there for a minute. Does the install script
>> check for CONFIG_XEN in the kernel config or something?
>
> Yes 10.2 mkinitrd does. But it still should work because a dom0
> kernel would obviously need all the drivers. A paravirt ops
> kernel native is like a dom0 variant.
Apparently not, given that the generated init script is mistaking
a native environment for a domU instead of a dom0.
In fact, when running 2.6.23-rc1 natively, no matter if compiled
with or without Xen support, the directory /proc/xen doesn't even
exist:
ts@xenon:~> uname -a
Linux xenon 2.6.23-rc1-testing #6 SMP PREEMPT Mon Jul 23 22:23:41 CEST 2007 i686 i686 i386 GNU/Linux
ts@xenon:~> ls -l /proc/xen/
ls: cannot access /proc/xen/: No such file or directory
ts@xenon:~>
The same holds for the non-Xen Suse kernel:
ts@xenon:~> uname -a
Linux xenon 2.6.18.8-0.5-default #1 SMP Fri Jun 22 12:17:53 UTC 2007 i686 i686 i386 GNU/Linux
ts@xenon:~> ls -l /proc/xen/
ls: cannot access /proc/xen/: No such file or directory
ts@xenon:~>
But when running Xen with the Opensuse Xen kernel as Dom0:
ts@xenon:~> uname -a
Linux xenon 2.6.18.8-0.5-xen #1 SMP Fri Jun 22 12:17:53 UTC 2007 i686 i686 i386 GNU/Linux
ts@xenon:~> ls -l /proc/xen/
total 0
-rw-r--r-- 1 root root 0 Jul 24 22:08 balloon
-r-------- 1 root root 0 Jul 24 22:08 capabilities
-r-------- 1 root root 0 Jul 24 22:01 privcmd
-r-------- 1 root root 0 Jul 24 22:08 xenbus
-rw------- 1 root root 0 Jul 24 22:01 xsd_kva
-r-------- 1 root root 0 Jul 24 22:08 xsd_port
ts@xenon:~> sudo cat /proc/xen/capabilities
root's password:
control_d
ts@xenon:~>
OTOH, the Opensuse Xen kernel vmlinuz-2.6.18.8-0.5-xen cannot even
be booted natively because GRUB complains immediately:
Error 13: Invalid or unsupported executable format
Conversely, the Xen loader flatly refuses to load a self-compiled,
Xen enabled 2.6.23-rc1 kernel as dom0, complaining:
DOM0 image is not an Xen-compatible Elf image.
So I guess the point is moot, because you cannot use the same image
as dom0 and natively, anyway.
Thanks,
Tilman
--
Tilman Schmidt E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 253 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: 2.6.22-git17 boot failure
2007-07-24 20:48 ` Tilman Schmidt
@ 2007-07-24 21:20 ` Jeremy Fitzhardinge
0 siblings, 0 replies; 27+ messages in thread
From: Jeremy Fitzhardinge @ 2007-07-24 21:20 UTC (permalink / raw)
To: Tilman Schmidt; +Cc: Andi Kleen, Olaf Hering, LKML, Gabriel C
Tilman Schmidt wrote:
> Apparently not, given that the generated init script is mistaking
> a native environment for a domU instead of a dom0.
>
> In fact, when running 2.6.23-rc1 natively, no matter if compiled
> with or without Xen support, the directory /proc/xen doesn't even
> exist:
>
No, the in-tree Xen stuff doesn't do anything with /proc/xen, and I
don't think I'll try to merge anything that does.
> OTOH, the Opensuse Xen kernel vmlinuz-2.6.18.8-0.5-xen cannot even
> be booted natively because GRUB complains immediately:
> Error 13: Invalid or unsupported executable format
> Conversely, the Xen loader flatly refuses to load a self-compiled,
> Xen enabled 2.6.23-rc1 kernel as dom0, complaining:
> DOM0 image is not an Xen-compatible Elf image.
> So I guess the point is moot, because you cannot use the same image
> as dom0 and natively, anyway.
>
No, but a dom0 kernel should look like a normal kernel from all the
device's perspective, with the added ability to fire up other domains.
When I get around to adding dom0 support to the pvops kernel, this will
all get even more fluid.
The simple answer is that if you want to test if you can probe PCI/load
PCI device drivers, you should just go ahead and try; it will either
work or not. No point testing something unrelated to see if you can.
The OpenSUSE init script is making the now-invalid assumption that you
can't have a CONFIG_XEN kernel that can talk to devices which isn't also
dom0. It needs to have its horizons broadened.
J
^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2007-07-24 21:21 UTC | newest]
Thread overview: 27+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-07-23 0:27 2.6.22-git17 boot failure Sid Boyce
-- strict thread matches above, loose matches on Subject: below --
2007-07-22 23:47 Tilman Schmidt
2007-07-23 0:31 ` Gabriel C
2007-07-23 0:52 ` Tilman Schmidt
2007-07-23 8:51 ` Jeremy Fitzhardinge
2007-07-23 10:25 ` Tilman Schmidt
2007-07-23 14:51 ` Jeremy Fitzhardinge
2007-07-23 19:42 ` Tilman Schmidt
2007-07-23 20:32 ` Jeremy Fitzhardinge
2007-07-23 23:02 ` Tilman Schmidt
2007-07-24 0:14 ` Jeremy Fitzhardinge
2007-07-24 8:51 ` Tilman Schmidt
2007-07-24 8:59 ` Jeremy Fitzhardinge
2007-07-24 9:10 ` Andi Kleen
2007-07-24 9:56 ` Olaf Hering
2007-07-24 10:36 ` Tilman Schmidt
2007-07-24 13:45 ` Olaf Hering
2007-07-24 15:45 ` Jeremy Fitzhardinge
2007-07-24 15:47 ` Andi Kleen
2007-07-24 18:08 ` Tilman Schmidt
2007-07-24 19:02 ` Jeremy Fitzhardinge
2007-07-24 19:12 ` Andi Kleen
2007-07-24 19:15 ` Jeremy Fitzhardinge
2007-07-24 20:48 ` Tilman Schmidt
2007-07-24 21:20 ` Jeremy Fitzhardinge
2007-07-24 3:46 ` Jeremy Fitzhardinge
2007-07-23 9:25 ` Andi Kleen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox