From: Jiri Slaby <jirislaby@gmail.com>
To: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>, Jiri Slaby <jirislaby@gmail.com>,
"Rafael J. Wysocki" <rjw@sisk.pl>,
Andrew Morton <akpm@linux-foundation.org>,
linux-kernel@vger.kernel.org,
Linux-pm mailing list <linux-pm@lists.linux-foundation.org>
Subject: Re: broken suspend [Was: 2.6.24-rc2-mm1]
Date: Sat, 17 Nov 2007 16:08:15 +0100 [thread overview]
Message-ID: <473F03DF.4020306@gmail.com> (raw)
In-Reply-To: <Pine.LNX.4.44L0.0711161058170.2738-100000@iolanthe.rowland.org>
On 11/16/2007 05:10 PM, Alan Stern wrote:
> On Thu, 15 Nov 2007, Greg KH wrote:
>
>>> The offending -mm patch is
>>> gregkh-driver-pm-acquire-device-locks-prior-to-suspending.patch
>>>
>>> 2.6.24-rc2-mm1 minus it works just fine; PROVE_LOCKING shows nothing new when
>>> the patch is applied.
>> Thanks for tracking this down. Alan, any thoughts?
>
> It's a driver problem somewhere. Probably not one of the most common
> drivers because I don't see the same problem here (but then I'm not
> testing -mm).
>
> The thing to do is figure out which driver is causing the problem.
> Jiri, try enabling CONFIG_DEBUG_DRIVER.
Sadly no output.
> If there's also a config
> option to prevent the console from being suspended, set it as well.
no_suspend_console kernel parameter has no effect (why?).
> Then you should be able to tell which driver is making trouble.
I think no unusual hardware inside:
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35 Express DRAM Controller
(rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express DRAM Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 c0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c0 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation 82G33/G31 Express Integrated Graphics
Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ff900000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c2 29 07 00 90 00 02 00 00 03 00 00 00 00
10: 00 00 a8 ff 01 ec 00 00 08 00 00 d0 00 00 90 ff
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c2 29
30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00
00:03.0 Communication controller: Intel Corporation 82G33/G31/P35 Express MEI
Controller (rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express MEI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ffa7bc00 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c4 29 06 00 10 00 02 00 80 07 00 00 80 00
10: 04 bc a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c4 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:03.2 IDE interface: Intel Corporation 82G33/G31/P35 Express PT IDER
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82G33/G31/P35 Express PT IDER Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 12
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c6 29 05 00 b0 00 02 85 01 01 00 00 00 00
10: 81 e8 00 00 01 e8 00 00 81 e4 00 00 01 e4 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 86 80 c6 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0c 03 00 00
00:03.3 Serial controller: Intel Corporation 82G33/G31/P35 Express Serial KT
Controller (rev 02) (prog-if 02 [16550])
Subsystem: Intel Corporation 82G33/G31/P35 Express Serial KT Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e000 [size=8]
Region 1: Memory at ffa7a000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c7 29 07 00 b0 00 02 02 00 07 00 00 00 00
10: 01 e0 00 00 00 a0 a7 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c7 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 05 02 00 00
00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network
Connection (rev 02)
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 318
Region 0: Memory at ffa40000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ffa79000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at dc00 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Address: 00000000fee0300c Data: 4191
Capabilities: [e0] Vendor Specific Information
00: 86 80 bd 10 07 04 10 00 02 00 00 02 00 00 00 00
10: 00 00 a4 ff 00 90 a7 ff 01 dc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 00 00
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0f 01 00 00
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 37 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 86 80 37 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 38 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 86 80 38 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 02 00 00
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d480 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 39 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d4 00 00 00 00 00 00 00 00 00 00 86 80 39 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ffa7b400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3c 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b4 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3c 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 04 00 00
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
(rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffa70000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00: 86 80 3e 29 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 00 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3e 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 34 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 86 80 34 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d080 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 35 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d0 00 00 00 00 00 00 00 00 00 00 86 80 35 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d000 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ffa7b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3a 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b0 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3a 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: ff600000-ff6fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
00: 86 80 4e 24 06 01 10 00 92 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00
00:1f.0 ISA bridge: Intel Corporation Unknown device 2910 (rev 02)
Subsystem: Intel Corporation Unknown device 2910
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 10 29 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA
AHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 319
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=32]
Region 5: Memory at ffa78800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4
Enable+
Address: fee0300c Data: 4169
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
Capabilities: [b0] Vendor Specific Information
00: 86 80 22 29 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 cc 00 00 81 c8 00 00 01 c8 00 00 81 c4 00 00
20: 01 c4 00 00 00 88 a7 ff 00 00 00 00 86 80 22 29
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 02 00 00
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) SMBus Controller
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ffa7b800 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00: 86 80 30 29 03 00 80 02 02 00 05 0c 00 00 00 00
10: 04 b8 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 86 80 30 29
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00
00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at b880 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at b480 [size=16]
Region 5: I/O ports at b400 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00: 86 80 26 29 07 00 b0 02 02 85 01 01 00 00 00 00
10: 01 c0 00 00 01 bc 00 00 81 b8 00 00 01 b8 00 00
20: 81 b4 00 00 01 b4 00 00 00 00 00 00 86 80 26 29
30: 00 00 00 00 70 00 00 00 00 00 00 00 03 02 00 00
00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family)
Thermal Subsystem (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 12
Region 0: Memory at ffa6f000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 32 29 02 00 10 00 02 00 80 11 00 00 00 00
10: 04 f0 a6 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 32 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00
01:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC
(rev 01)
Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ff6f0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 8c 16 13 00 16 00 90 02 01 00 00 02 08 a8 00 00
10: 00 00 6f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 5f 18 12 10
30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 01 0a 1c
Plugged usb devices:
Bus 004 Device 007: ID 045e:00f0 Microsoft Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x00f0
bcdDevice 1.01
iManufacturer 1 Microsoft Corporation
iProduct 2 Microsoft � Laser Mouse 6000
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 33 US
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 59
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10
Bus 004 Device 006: ID 0458:004c KYE Systems Corp. (Mouse Systems) Slimstar Pro
Keyboard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0458 KYE Systems Corp. (Mouse Systems)
idProduct 0x004c Slimstar Pro Keyboard
bcdDevice 1.01
iManufacturer 1 ABBHOME
iProduct 2 USB Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 50mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 104
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Bus 004 Device 005: ID 04b4:2050 Cypress Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x2050
bcdDevice 0.01
iManufacturer 1 Bella Corporation
iProduct 2 GBella Corporation DV Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 25 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x60
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power
regards,
--
Jiri Slaby (jirislaby@gmail.com)
Faculty of Informatics, Masaryk University
next prev parent reply other threads:[~2007-11-17 15:08 UTC|newest]
Thread overview: 148+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-14 1:59 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 3:12 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 3:49 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 4:39 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-14 5:33 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 8:23 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-14 9:23 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-15 17:15 ` 2.6.24-rc2-mm1 Matthew Dharm
2007-11-15 18:14 ` 2.6.24-rc2-mm1 Boaz Harrosh
2007-11-15 21:42 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 4:18 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 20:29 ` 2.6.24-rc2-mm1 mark gross
2007-11-14 20:40 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 17:22 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 20:05 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 17:23 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 19:19 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 21:40 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-15 22:56 ` 2.6.24-rc2-mm1 mark gross
2007-11-15 23:01 ` [PATCH] pm-qos-remove-locks-around-blocking-notifier.patch ... was 2.6.24-rc2-mm1 mark gross
2007-11-14 3:40 ` [PATCH] Fix build failure when CONFIG_INFINIBAND_IPOIB_CM is not defined Tony Breeds
2007-11-15 14:49 ` Mel Gorman
2007-11-14 3:41 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 4:55 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 5:10 ` 2.6.24-rc2-mm1 Ulrich Drepper
2007-11-14 5:27 ` 2.6.24-rc2-mm1 Gabriel C
2007-11-14 5:45 ` 2.6.24-rc2-mm1 Zan Lynx
2007-11-14 6:18 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 6:38 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 6:47 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 8:41 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 9:32 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 9:36 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 16:59 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 18:38 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-14 19:19 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 21:27 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 1:01 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 2:38 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 3:11 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 8:14 ` 2.6.24-rc2-mm1 Dave Young
2007-11-15 8:51 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 17:06 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 17:16 ` 2.6.24-rc2-mm1 Kay Sievers
2007-11-15 18:59 ` 2.6.24-rc2-mm1 Greg KH
2007-11-14 6:32 ` [PATCH] [2.6.24-rc2-mm1] Fix dependencies for FSL_DMA Olof Johansson
2007-11-14 8:56 ` 2.6.24-rc2-mm1 -- mkfs failing on variety of fs types Andy Whitcroft
2007-11-14 10:28 ` Andrew Morton
2007-11-14 10:46 ` Dmitry Monakhov
2007-11-14 14:40 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 14:59 ` 2.6.24-rc2-mm1 Matthias Urlichs
2007-11-14 15:04 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 15:43 ` 2.6.24-rc2-mm1 Matthias Urlichs
2007-11-14 15:49 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 16:29 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 16:39 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 16:40 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 17:02 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 17:38 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-14 18:19 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 19:23 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 21:41 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-15 21:53 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-15 22:04 ` 2.6.24-rc2-mm1 Jiri Kosina
2007-11-16 0:39 ` 2.6.24-rc2-mm1 Dave Young
2007-11-16 0:49 ` 2.6.24-rc2-mm1 Greg KH
2007-11-16 0:55 ` 2.6.24-rc2-mm1 Dave Young
2007-11-14 19:16 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 20:29 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-14 20:55 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 22:48 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 17:36 ` 2.6.24-rc2-mm1 Jan Blunck
2007-11-15 18:36 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 21:24 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-15 21:34 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-16 5:29 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-16 14:03 ` 2.6.24-rc2-mm1 Jan Blunck
2007-11-16 20:11 ` 2.6.24-rc2-mm1 Torsten Kaiser
2007-11-14 20:24 ` broken suspend [Was: 2.6.24-rc2-mm1] Jiri Slaby
2007-11-14 20:36 ` Andrew Morton
2007-11-14 21:48 ` Rafael J. Wysocki
2007-11-15 23:59 ` Jiri Slaby
2007-11-16 0:38 ` Greg KH
2007-11-16 16:10 ` Alan Stern
2007-11-17 15:08 ` Jiri Slaby [this message]
2007-11-17 15:12 ` Jiri Slaby
2007-11-17 16:13 ` Alan Stern
2007-11-17 20:37 ` Rafael J. Wysocki
2007-11-17 21:58 ` Alan Stern
2007-11-18 12:42 ` Jiri Slaby
2007-11-18 13:06 ` Jiri Slaby
2007-11-18 13:42 ` Rafael J. Wysocki
2007-11-18 13:53 ` Jiri Slaby
2007-11-18 15:03 ` Rafael J. Wysocki
2007-11-18 14:49 ` Jiri Slaby
2007-11-18 15:23 ` Rafał J. Wysocki
2007-11-18 15:15 ` Jiri Slaby
2007-11-18 17:07 ` Alan Stern
2007-11-18 19:09 ` Jiri Slaby
2007-11-18 22:27 ` Jiri Slaby
2007-11-19 3:04 ` Alan Stern
2007-11-19 20:01 ` Rudolf Marek
2007-11-19 20:27 ` Alan Stern
2007-11-20 13:15 ` [lm-sensors] " Mark M. Hoffman
2007-11-21 0:00 ` Rafael J. Wysocki
2007-11-21 15:54 ` Alan Stern
2007-11-21 19:19 ` Rafael J. Wysocki
2007-11-26 8:57 ` Jiri Slaby
2007-11-19 21:53 ` Rafael J. Wysocki
2007-11-18 22:27 ` Rafael J. Wysocki
2007-11-18 22:12 ` Jiri Slaby
2007-11-18 22:42 ` Rafael J. Wysocki
2007-11-15 4:29 ` 2.6.24-rc2-mm1 (memory hotplug x86_64/vmemmap fix) KAMEZAWA Hiroyuki
2007-11-15 5:39 ` Kamalesh Babulal
2007-11-15 8:56 ` Andrew Morton
2007-11-15 9:18 ` KAMEZAWA Hiroyuki
2007-11-15 10:30 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [0/3] KAMEZAWA Hiroyuki
2007-11-15 10:33 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [1/3] memory_add_physaddr_to_nid export for acpi memhotplug.ko KAMEZAWA Hiroyuki
2007-11-15 10:35 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [2/3] fix section mismatch in vmammap_allock_block KAMEZAWA Hiroyuki
2007-11-16 0:53 ` Andrew Morton
2007-11-16 4:45 ` KAMEZAWA Hiroyuki
2007-11-15 10:36 ` [PATCH][2.6.24-rc2-mm1] memory hotplug x86_64 fix [3/3] fix section mismatch in init_memory_mapping KAMEZAWA Hiroyuki
2007-11-16 0:59 ` Andrew Morton
2007-11-16 5:09 ` KAMEZAWA Hiroyuki
2007-11-15 9:39 ` 2.6.24-rc2-mm1 (memory hotplug x86_64/vmemmap fix) Andy Whitcroft
2007-11-15 10:05 ` KAMEZAWA Hiroyuki
2007-11-15 10:02 ` 2.6.24-rc2-mm1 -- strange apparent network failures Andy Whitcroft
2007-11-16 0:28 ` Kevin Winchester
2007-11-16 0:44 ` Andrew Morton
2007-11-16 1:01 ` Kevin Winchester
2007-11-16 1:09 ` Andrew Morton
2007-11-17 5:16 ` Andrew Morgan
2007-11-17 12:48 ` Kevin Winchester
2007-11-17 23:52 ` Andrew Morgan
2007-11-18 0:50 ` Kevin Winchester
2007-11-18 1:17 ` Kevin Winchester
2007-11-18 1:57 ` Andrew Morgan
2007-11-18 1:23 ` Kevin Winchester
2007-11-17 13:57 ` Andy Whitcroft
2007-11-16 1:21 ` Tom
2007-11-15 10:50 ` 2.6.24-rc2-mm1 -- QLogics ISP1020 gone missing Andy Whitcroft
2007-11-15 19:25 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 20:47 ` 2.6.24-rc2-mm1 Andrew Morton
2007-11-16 0:01 ` 2.6.24-rc2-mm1 Greg KH
2007-11-15 22:25 ` 2.6.24-rc2-mm1: undefined reference to `local_apic_timer_c2_ok' Mariusz Kozlowski
2007-11-15 22:49 ` Len Brown
2007-11-15 23:35 ` Mariusz Kozlowski
2007-11-15 22:34 ` [PATCH] parisc: balance parenthesis in pte_free_kernel() Mariusz Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=473F03DF.4020306@gmail.com \
--to=jirislaby@gmail.com \
--cc=akpm@linux-foundation.org \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@lists.linux-foundation.org \
--cc=rjw@sisk.pl \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox