* 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
@ 2008-04-20 1:27 Sid Boyce
2008-04-20 2:29 ` Bernd Eckenfels
` (2 more replies)
0 siblings, 3 replies; 10+ messages in thread
From: Sid Boyce @ 2008-04-20 1:27 UTC (permalink / raw)
To: linux-kernel
2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
With xfs it can't find these and drops into a shell.
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
swap defaults 0 0
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
xfs defaults 1 1
From my .config
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
The other boxes are configure pretty much the same, but I can diff the
.config's if required.
# l /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
-rw-r--r-- 1 root root 272240 2008-04-19 21:54
/lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
Raid II Controller (rev 01)
From working 2.6.25
# lsmod|grep sata
sata_nv 36872 2
sata_sil24 26692 0
libata 173664 3 pata_amd,sata_nv,sata_sil24
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-20 1:27 Sid Boyce
@ 2008-04-20 2:29 ` Bernd Eckenfels
2008-04-20 11:25 ` Alexey Dobriyan
2008-04-21 3:20 ` Eric Sandeen
2 siblings, 0 replies; 10+ messages in thread
From: Bernd Eckenfels @ 2008-04-20 2:29 UTC (permalink / raw)
To: linux-kernel
In article <480A9C1E.8050505@blueyonder.co.uk> you wrote:
> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
> With xfs it can't find these and drops into a shell.
Do you have reiser and ext3 as modules as well? If yes, how do you load them
(i.e. which distribution, bootload and initram you are using?)
Gruss
Bernd
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
@ 2008-04-20 3:28 Sid Boyce
0 siblings, 0 replies; 10+ messages in thread
From: Sid Boyce @ 2008-04-20 3:28 UTC (permalink / raw)
To: linux-kernel
In article <480A9C1E.8050505@xxxxxxxxxxxxxxxx> you wrote:
>> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
>> With xfs it can't find these and drops into a shell.
> Do you have reiser and ext3 as modules as well? If yes, how do you
load them
> (i.e. which distribution, bootload and initram you are using?)
> Gruss
> Bernd
Distro is openSUSE 11.0 Beta1 on all boxes, only one with xfs.
I have reiserfs, jfs, ext3 and xfs all as modules, loaded by mkinitrd.
Kernel image: /boot/2.6.25-git2-smp
Initrd image: /boot/initrd2.6.25-git2-smp
Root device:
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1
(/dev/sda1) (mounted on / as xfs)
Resume device: /dev/sda2
Kernel Modules: processor thermal dock scsi_mod libata sata_sil24
sata_nv pata_amd fan xfs edd sd_mod usbcore ohci-hcd uhci-hcd ehci-hcd
ff-memless hid usbhid
Features: block usb resume.userspace resume.kernel
Bootsplash: openSUSE (1024x768)
73057 blocks
From /boot/grub/menu.lst
# Modified by YaST2. Last modification on Sat Apr 19 23:11:11 BST 2008
default 2
timeout 8
##YaST - generic_mbr
gfxmenu (hd0,0)/boot/message
###Don't change this comment - YaST2 identifier: Original name:
linux-git2-smp###
title 2.6.25-git2-smp
root (hd0,0)
kernel /boot/2.6.25-git2-smp
root=/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1
vga=0x31a resume=/dev/sda2 splash=silent showopts elevator=cfq
initrd /boot/initrd2.6.25-git2-smp
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-20 1:27 Sid Boyce
2008-04-20 2:29 ` Bernd Eckenfels
@ 2008-04-20 11:25 ` Alexey Dobriyan
2008-04-20 12:38 ` Sid Boyce
2008-04-21 3:20 ` Eric Sandeen
2 siblings, 1 reply; 10+ messages in thread
From: Alexey Dobriyan @ 2008-04-20 11:25 UTC (permalink / raw)
To: Sid Boyce; +Cc: linux-kernel
On Sun, Apr 20, 2008 at 02:27:58AM +0100, Sid Boyce wrote:
> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
> With xfs it can't find these and drops into a shell.
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
> swap defaults 0 0
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
> xfs defaults 1 1
>
> From my .config
> CONFIG_XFS_FS=m
> CONFIG_XFS_QUOTA=y
> CONFIG_XFS_POSIX_ACL=y
> CONFIG_XFS_RT=y
>
> The other boxes are configure pretty much the same, but I can diff the
> .config's if required.
> # l /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
> -rw-r--r-- 1 root root 272240 2008-04-19 21:54
> /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
>
> 00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
> 00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
> Raid II Controller (rev 01)
>
> From working 2.6.25
> # lsmod|grep sata
> sata_nv 36872 2
> sata_sil24 26692 0
> libata 173664 3 pata_amd,sata_nv,sata_sil24
Double check that you've enabled CONFIG_ATA_SFF and then check you
previous CONFIG_SATA_* options.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-20 11:25 ` Alexey Dobriyan
@ 2008-04-20 12:38 ` Sid Boyce
2008-04-21 11:54 ` Marc Dionne
0 siblings, 1 reply; 10+ messages in thread
From: Sid Boyce @ 2008-04-20 12:38 UTC (permalink / raw)
To: Alexey Dobriyan; +Cc: linux-kernel
Alexey Dobriyan wrote:
> On Sun, Apr 20, 2008 at 02:27:58AM +0100, Sid Boyce wrote:
>> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
>> With xfs it can't find these and drops into a shell.
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
>> swap defaults 0 0
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
>> xfs defaults 1 1
>>
>> From my .config
>> CONFIG_XFS_FS=m
>> CONFIG_XFS_QUOTA=y
>> CONFIG_XFS_POSIX_ACL=y
>> CONFIG_XFS_RT=y
>>
>> The other boxes are configure pretty much the same, but I can diff the
>> .config's if required.
>> # l /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
>> -rw-r--r-- 1 root root 272240 2008-04-19 21:54
>> /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
>>
>> 00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
>> 00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>> 00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>> 00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>> 03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
>> Raid II Controller (rev 01)
>>
>> From working 2.6.25
>> # lsmod|grep sata
>> sata_nv 36872 2
>> sata_sil24 26692 0
>> libata 173664 3 pata_amd,sata_nv,sata_sil24
>
> Double check that you've enabled CONFIG_ATA_SFF and then check you
> previous CONFIG_SATA_* options.
>
On Sun, Apr 20, 2008 at 02:27:58AM +0100, Sid Boyce wrote:
> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
> With xfs it can't find these and drops into a shell.
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
> swap defaults 0 0
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
> xfs defaults 1 1
>
> From my .config
> CONFIG_XFS_FS=m
> CONFIG_XFS_QUOTA=y
> CONFIG_XFS_POSIX_ACL=y
> CONFIG_XFS_RT=y
>
> The other boxes are configure pretty much the same, but I can diff the
> .config's if required.
> # l /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
> -rw-r--r-- 1 root root 272240 2008-04-19 21:54
> /lib/modules/2.6.25-git2-smp/kernel/drivers/ata/sata_sil.ko
>
> 00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
> 00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> 03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
> Raid II Controller (rev 01)
>
> From working 2.6.25
> # lsmod|grep sata
> sata_nv 36872 2
> sata_sil24 26692 0
> libata 173664 3 pata_amd,sata_nv,sata_sil24
I started off using the 2.6.25 .config below, 2.6.25-git "make
oldconfig", changed a few options like SATA_SFF and SATA_PMP.
barrabas:/usr/src/linux-2.6.25 # grep SFF .config
CONFIG_BLK_DEV_IDEDMA_SFF=y
barrabas:/usr/src/linux-2.6.25 # grep SATA .config
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_SATA_AHCI=m
CONFIG_SATA_SVW=m
CONFIG_SATA_MV=m
CONFIG_SATA_NV=m
CONFIG_SATA_QSTOR=m
CONFIG_SATA_PROMISE=m
CONFIG_SATA_SX4=m
CONFIG_SATA_SIL=m
CONFIG_SATA_SIL24=m
CONFIG_SATA_SIS=m
CONFIG_SATA_ULI=m
CONFIG_SATA_VIA=m
CONFIG_SATA_VITESSE=m
CONFIG_SATA_INIC162X=m
> Double check that you've enabled CONFIG_ATA_SFF and then check you
previous CONFIG_SATA_* options.
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-20 1:27 Sid Boyce
2008-04-20 2:29 ` Bernd Eckenfels
2008-04-20 11:25 ` Alexey Dobriyan
@ 2008-04-21 3:20 ` Eric Sandeen
2 siblings, 0 replies; 10+ messages in thread
From: Eric Sandeen @ 2008-04-21 3:20 UTC (permalink / raw)
To: g3vbv; +Cc: linux-kernel
Sid Boyce wrote:
> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
> With xfs it can't find these and drops into a shell.
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
> swap defaults 0 0
> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
> xfs defaults 1 1
>
> From my .config
> CONFIG_XFS_FS=m
> CONFIG_XFS_QUOTA=y
> CONFIG_XFS_POSIX_ACL=y
> CONFIG_XFS_RT=y
>
> The other boxes are configure pretty much the same, but I can diff the
> .config's if required.
Does it not find the device, or does it not find the filesystem? What's
the relevant message? Does it enumerate the partitions it finds, and is
your partition in the list? Do you see the xfs module initialization
message go by before the error to indicate that it really did get loaded?
-Eric
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-20 12:38 ` Sid Boyce
@ 2008-04-21 11:54 ` Marc Dionne
2008-04-21 13:40 ` Sid Boyce
0 siblings, 1 reply; 10+ messages in thread
From: Marc Dionne @ 2008-04-21 11:54 UTC (permalink / raw)
To: g3vbv; +Cc: Alexey Dobriyan, linux-kernel
On Sun, Apr 20, 2008 at 8:38 AM, Sid Boyce <g3vbv@blueyonder.co.uk> wrote:
> > > 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
> > > With xfs it can't find these and drops into a shell.
> > > /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
> > > swap defaults 0 0
> > > /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
> > > xfs defaults 1 1
> > >
> > > 00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
> > > 00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> > > 00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> > > 00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
> > > 03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
> > > Raid II Controller (rev 01)
Perhaps related to these threads ?
http://marc.info/?l=linux-ide&m=120866699221716
http://marc.info/?l=linux-scsi&m=120854308421912
Marc
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap)partitions on a SATA drive
@ 2008-04-21 11:55 Sid Boyce
0 siblings, 0 replies; 10+ messages in thread
From: Sid Boyce @ 2008-04-21 11:55 UTC (permalink / raw)
To: linux-kernel
Eric Sandeen wrote:
> Sid Boyce wrote:
>> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
>> With xfs it can't find these and drops into a shell.
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
>> swap defaults 0 0
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
>> xfs defaults 1 1
>>
>> From my .config
>> CONFIG_XFS_FS=m
>> CONFIG_XFS_QUOTA=y
>> CONFIG_XFS_POSIX_ACL=y
>> CONFIG_XFS_RT=y
>>
>> The other boxes are configure pretty much the same, but I can diff the
>> .config's if required.
> Does it not find the device, or does it not find the filesystem? What's
> the relevant message? Does it enumerate the partitions it finds, and is
> your partition in the list? Do you see the xfs module initialization
> message go by before the error to indicate that it really did get loaded?
> -Eric
It doesn't find the device either with 2.6.25-git1 or 2.6.25-git2. I've
tried a new kernel with xfs compiled in rather than as a module. The odd
thing is that other boxes with ext3, jfs and reiserfs are fine, 2 of
them with SATA drives are working with 2.6.25-git2.
The BIOS settings (it's the latest BIOS), but it's OK on 2.6.25, just a
problem from 2.6.25-git1.
Primary IDE Master [Optiarc DVD RW A]
SATA 1 [WDC WD5000AAKS-0]
SATA2 to SATA6 [None]
(Onboard Device Configuration)
Silicon SATAII Controller [SATA Mode]
Here goes the messages on boot for 2.6.25-git2.
-----------------------------------------------
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host n128@0xfdef8000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host n128@0xfdeff000 port 0xfdefa000 irq 16
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
sata_nv 0000:00:0d.0 using SUNCQ mode
scsi2: sata_nv
--- ditto to scsi16 ----
FATAL: Module xfs not found ### I have it built-in this time ###
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
Creating device nodes with udev
<<< USB STUFF NOT INCLUDED >>>>
Trying normal resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Trying manual resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Waiting for device
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear
could not find
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1
Want me to fall back to
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1? (Y/n) y
Waiting for device
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear
not found -- exiting to /bin/sh
$
-----------------------------------
There is no /dev/disk directory, /sys/block/ is empty
From 2.6.25 dmesg
==================
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdefa000 irq 16
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input2
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
sata_nv 0000:00:0d.0: version 3.5
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 23
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 23
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133
ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
usbcore: registered new device driver usb
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions on a SATA drive
2008-04-21 11:54 ` Marc Dionne
@ 2008-04-21 13:40 ` Sid Boyce
0 siblings, 0 replies; 10+ messages in thread
From: Sid Boyce @ 2008-04-21 13:40 UTC (permalink / raw)
To: Marc Dionne; +Cc: Alexey Dobriyan, linux-kernel
Marc Dionne wrote:
> On Sun, Apr 20, 2008 at 8:38 AM, Sid Boyce <g3vbv@blueyonder.co.uk> wrote:
>>>> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
>>>> With xfs it can't find these and drops into a shell.
>>>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
>>>> swap defaults 0 0
>>>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
>>>> xfs defaults 1 1
>>>>
>>>> 00:0c.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
>>>> 00:0d.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>>>> 00:0d.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>>>> 00:0d.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
>>>> 03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
>>>> Raid II Controller (rev 01)
>
> Perhaps related to these threads ?
> http://marc.info/?l=linux-ide&m=120866699221716
The one above seems close to what I experience.
> http://marc.info/?l=linux-scsi&m=120854308421912
The patch is already mainstream.
>
> Marc
>
>
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap)partitions on a SATA drive
@ 2008-04-21 21:10 Sid Boyce
0 siblings, 0 replies; 10+ messages in thread
From: Sid Boyce @ 2008-04-21 21:10 UTC (permalink / raw)
To: linux-kernel
-------- Original Message --------
Subject: Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2
(swap)partitions on a SATA drive]
Date: Mon, 21 Apr 2008 14:49:40 +0100
From: Sid Boyce <sboyce@blueyonder.co.uk>
Reply-To: sboyce@blueyonder.co.uk
Organization: blueyonder.co.uk
To: linux-kernel@vger.kernel.org
Looks like this earlier message didn't get through.
Sid.
-------- Original Message --------
Subject: Re: 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2
(swap)partitions on a SATA drive
Date: Mon, 21 Apr 2008 12:55:04 +0100
From: Sid Boyce <g3vbv@blueyonder.co.uk>
Reply-To: g3vbv@blueyonder.co.uk
Organization: blueyonder.co.uk
To: linux-kernel@vger.kernel.org
Eric Sandeen wrote:
> Sid Boyce wrote:
>> 2.6.25 x86_64 boots fine as does -git1/2 boxes using reiserfs and ext3.
>> With xfs it can't find these and drops into a shell.
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part2 swap
>> swap defaults 0 0
>> /dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 /
>> xfs defaults 1 1
>>
>> From my .config
>> CONFIG_XFS_FS=m
>> CONFIG_XFS_QUOTA=y
>> CONFIG_XFS_POSIX_ACL=y
>> CONFIG_XFS_RT=y
>>
>> The other boxes are configure pretty much the same, but I can diff the
>> .config's if required.
> Does it not find the device, or does it not find the filesystem? What's
> the relevant message? Does it enumerate the partitions it finds, and is
> your partition in the list? Do you see the xfs module initialization
> message go by before the error to indicate that it really did get loaded?
> -Eric
It doesn't find the device either with 2.6.25-git1 or 2.6.25-git2. I've
tried a new kernel with xfs compiled in rather than as a module. The odd
thing is that other boxes with ext3, jfs and reiserfs are fine, 2 of
them with SATA drives are working with 2.6.25-git2.
The BIOS settings (it's the latest BIOS), but it's OK on 2.6.25, just a
problem from 2.6.25-git1.
Primary IDE Master [Optiarc DVD RW A]
SATA 1 [WDC WD5000AAKS-0]
SATA2 to SATA6 [None]
(Onboard Device Configuration)
Silicon SATAII Controller [SATA Mode]
Here goes the messages on boot for 2.6.25-git2.
-----------------------------------------------
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host n128@0xfdef8000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host n128@0xfdeff000 port 0xfdefa000 irq 16
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
sata_nv 0000:00:0d.0 using SUNCQ mode
scsi2: sata_nv
--- ditto to scsi16 ----
FATAL: Module xfs not found ### I have it built-in this time ###
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
Creating device nodes with udev
<<< USB STUFF NOT INCLUDED >>>>
Trying normal resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Trying manual resume from /dev/sda2
resume device /dev/sda2 not found (ignoring)
Waiting for device
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear
could not find
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1
Want me to fall back to
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1? (Y/n) y
Waiting for device
/dev/disk/by-id/scsi-SATA_WDC_WD5000AAKS-_WD-WCAS85018679-part1 to appear
not found -- exiting to /bin/sh
$
-----------------------------------
There is no /dev/disk directory, /sys/block/ is empty
From 2.6.25 dmesg
==================
scsi0 : sata_sil24
scsi1 : sata_sil24
ata1: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdef8000 irq 16
ata2: SATA max UDMA/100 host m128@0xfdeff000 port 0xfdefa000 irq 16
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input2
ata1: SATA link down (SStatus 0 SControl 0)
ata2: SATA link down (SStatus 0 SControl 0)
sata_nv 0000:00:0d.0: version 3.5
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 23
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 23
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133
ata3.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
usbcore: registered new device driver usb
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2
Regards
Sid.
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
--
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2008-04-21 21:10 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-04-21 11:55 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap)partitions on a SATA drive Sid Boyce
-- strict thread matches above, loose matches on Subject: below --
2008-04-21 21:10 Sid Boyce
2008-04-20 3:28 2.6.25-git1/2 not seeing /dev/sda1 (XFS root) or /dev/sda2 (swap) partitions " Sid Boyce
2008-04-20 1:27 Sid Boyce
2008-04-20 2:29 ` Bernd Eckenfels
2008-04-20 11:25 ` Alexey Dobriyan
2008-04-20 12:38 ` Sid Boyce
2008-04-21 11:54 ` Marc Dionne
2008-04-21 13:40 ` Sid Boyce
2008-04-21 3:20 ` Eric Sandeen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox