[2.6.25] lpfc driver problem

[2.6.25] lpfc driver problem

[Gerhard Mack]

hello

I'm getting the following error when trying to load the lpfc driver.  This 
is a new install so I have no idea if this is a regression or not.

dmesg output:
Emulex LightPulse Fibre Channel SCSI driver 8.2.5
Copyright(c) 2004-2008 Emulex.  All rights reserved.
scsi2 :  on PCI bus 02 device 50 irq 24
lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
x400000, FW Data: A8 x0 AC x0
lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
x400000, FW Data: A8 x0 AC x0

Card is:
02:0a.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host 
Adapter (rev 02)
02:0a.0 0c04: 10df:f800 (rev 02)


--
Gerhard Mack

gmack@innerfire.net

<>< As a computer I find your faith in technology amusing.

Re: [2.6.25] lpfc driver problem

[Andrew Morton]

On Tue, 29 Apr 2008 16:28:03 -0400 (EDT) Gerhard Mack <gmack@innerfire.net> wrote:

> hello
> 
> I'm getting the following error when trying to load the lpfc driver.  This 
> is a new install so I have no idea if this is a regression or not.
> 
> dmesg output:
> Emulex LightPulse Fibre Channel SCSI driver 8.2.5
> Copyright(c) 2004-2008 Emulex.  All rights reserved.
> scsi2 :  on PCI bus 02 device 50 irq 24
> lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
> x400000, FW Data: A8 x0 AC x0
> lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
> x400000, FW Data: A8 x0 AC x0
> 
> Card is:
> 02:0a.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host 
> Adapter (rev 02)
> 02:0a.0 0c04: 10df:f800 (rev 02)

(Cc's added)

Re: [2.6.25] lpfc driver problem

[Gerhard Mack]

> On Tue, 29 Apr 2008 16:28:03 -0400 (EDT) Gerhard Mack <gmack@innerfire.net> wrote:
> 
> > hello
> > 
> > I'm getting the following error when trying to load the lpfc driver.  This 
> > is a new install so I have no idea if this is a regression or not.
> > 
> > dmesg output:
> > Emulex LightPulse Fibre Channel SCSI driver 8.2.5
> > Copyright(c) 2004-2008 Emulex.  All rights reserved.
> > scsi2 :  on PCI bus 02 device 50 irq 24
> > lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
> > x400000, FW Data: A8 x0 AC x0
> > lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
> > x400000, FW Data: A8 x0 AC x0
> > 
> > Card is:
> > 02:0a.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host 
> > Adapter (rev 02)
> > 02:0a.0 0c04: 10df:f800 (rev 02)
> 
> (Cc's added)

I am no longer able to debug this.  My client took the card back and 
traded it for a Qlogic.

	Gerhard
 

--
Gerhard Mack

gmack@innerfire.net

<>< As a computer I find your faith in technology amusing.

Re: [2.6.25] lpfc driver problem

[James Smart]

Gerhard Mack wrote:
> 
>> On Tue, 29 Apr 2008 16:28:03 -0400 (EDT) Gerhard Mack <gmack@innerfire.net> wrote:
>>
>>> hello
>>>
>>> I'm getting the following error when trying to load the lpfc driver.  This 
>>> is a new install so I have no idea if this is a regression or not.
>>>
>>> dmesg output:
>>> Emulex LightPulse Fibre Channel SCSI driver 8.2.5
>>> Copyright(c) 2004-2008 Emulex.  All rights reserved.
>>> scsi2 :  on PCI bus 02 device 50 irq 24
>>> lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
>>> x400000, FW Data: A8 x0 AC x0
>>> lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg 
>>> x400000, FW Data: A8 x0 AC x0
>>>
>>> Card is:
>>> 02:0a.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host 
>>> Adapter (rev 02)
>>> 02:0a.0 0c04: 10df:f800 (rev 02)
>> (Cc's added)

The error indicates that the adapter did not respond to a basic port reset,
which we do before we try to bring up it's messaging interface, etc.
This likely means it failed POST or some other hardware error. The LED's on
the backpanel would have indicated the condition. The LP8000 is a pretty old
board and was EOL'd years ago, so it doesn't surprise me that something like
this could pop up.

> 
> I am no longer able to debug this.  My client took the card back and 
> traded it for a Qlogic.

As much as any vendor hates to see a customer switch :( I understand expediency...

As an fyi - to help the debug, whether it be Emulex or Qlogic, or someone else,
I recommend that you cat the various /sys/class/scsi_host/hostX/* and
/sys/class/fc_host/hostX/* attributes (where hostX corresponds to the scsi? bus\
number assigned to the adapter).  Assuming the adapter attaches enough for these
things to exist, it will give us a lot more information about the adapter for debug.

-- james s

> 
> 	Gerhard
>  
> 
> --
> Gerhard Mack
> 
> gmack@innerfire.net
> 
> <>< As a computer I find your faith in technology amusing.
> 

Re: [2.6.25] lpfc driver problem

[Gerhard Mack]

On Fri, 2 May 2008, James Smart wrote:
> Gerhard Mack wrote:
> > 
> > > On Tue, 29 Apr 2008 16:28:03 -0400 (EDT) Gerhard Mack
> > > <gmack@innerfire.net> wrote:
> > > 
> > > > hello
> > > > 
> > > > I'm getting the following error when trying to load the lpfc driver.
> > > > This is a new install so I have no idea if this is a regression or not.
> > > > 
> > > > dmesg output:
> > > > Emulex LightPulse Fibre Channel SCSI driver 8.2.5
> > > > Copyright(c) 2004-2008 Emulex.  All rights reserved.
> > > > scsi2 :  on PCI bus 02 device 50 irq 24
> > > > lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg
> > > > x400000, FW Data: A8 x0 AC x0
> > > > lpfc 0000:02:0a.0: 0:0436 Adapter failed to init, timeout, status reg
> > > > x400000, FW Data: A8 x0 AC x0
> > > > 
> > > > Card is:
> > > > 02:0a.0 Fibre Channel: Emulex Corporation LP8000 Fibre Channel Host
> > > > Adapter (rev 02)
> > > > 02:0a.0 0c04: 10df:f800 (rev 02)
> > > (Cc's added)
> 
> The error indicates that the adapter did not respond to a basic port reset,
> which we do before we try to bring up it's messaging interface, etc.
> This likely means it failed POST or some other hardware error. The LED's on
> the backpanel would have indicated the condition. The LP8000 is a pretty old
> board and was EOL'd years ago, so it doesn't surprise me that something like
> this could pop up.
> 

Not shocking.... my customers tend to spend more in my wages than they 
would have saved on hardware buying things from the junk pile.  This was 
actually the 4th non working card from said computer junk store.

> > 
> > I am no longer able to debug this.  My client took the card back and traded
> > it for a Qlogic.
> 
> As much as any vendor hates to see a customer switch :( I understand
> expediency...

If it makes you feel better I have a Qlogic that causes the machine to 
reset during the bios init.

> 
> As an fyi - to help the debug, whether it be Emulex or Qlogic, or someone
> else,
> I recommend that you cat the various /sys/class/scsi_host/hostX/* and
> /sys/class/fc_host/hostX/* attributes (where hostX corresponds to the scsi?
> bus\
> number assigned to the adapter).  Assuming the adapter attaches enough for
> these
> things to exist, it will give us a lot more information about the adapter for
> debug.

I don't think it attached long enough for that to happen.

	Gerhard


--
Gerhard Mack

gmack@innerfire.net

<>< As a computer I find your faith in technology amusing.