[PARIDE] Datastor EP-2000 problem

[PARIDE] Datastor EP-2000 problem

[Rene Herman]

Good day.

Dug up a parallel port CD-RW consisting of a Philips CDD3801 24x/2x/2x 
ATAPI CD-RW hooked up to a Datastor EP-2000 parallel interface chip.

The drive has been verified to work correctly when used directly as IDE 
and the parallel interface has been verified to work correctly with some 
random other CD-ROM drive. The combination bombs out though.

The drive is found:

root@ax6bc:~# modprobe dstr
root@ax6bc:~# modprobe pcd
root@ax6bc:~# dmesg | tail -6
pcd: pcd version 1.07, major 46, nice 0
pcd0: Sharing parport0 at 0x378
pcd0: dstr 1.01, DataStor EP2000 at 0x378, mode 4 (EPP-32), delay 1
pcd0: Master: R/RW 2x2x24
pcd0: mode sense capabilities completion: alt=0x51 stat=0x51 err=0x60 
loop=0 phase=3
pcd0: mode sense capabilities: Sense key: 6, ASC: 29, ASQ: 0

trying to extract any data from it fails though:

root@ax6bc:~# dd if=/dev/pcd0 of=/dev/null bs=2048 count=1
0+0 records in
0+0 records out
0 bytes (0 B) copied, 12.5765 s, 0.0 kB/s

root@ax6bc:~# dmesg | tail -14
pcd: pcd version 1.07, major 46, nice 0
pcd0: Sharing parport0 at 0x378
pcd0: dstr 1.01, DataStor EP2000 at 0x378, mode 4 (EPP-32), delay 1
pcd0: Master: R/RW 2x2x24
pcd0: mode sense capabilities completion: alt=0x51 stat=0x51 err=0x60 
loop=0 phase=3
pcd0: mode sense capabilities: Sense key: 6, ASC: 29, ASQ: 0
pcd0: WARNING: ATAPI phase errors
pcd0: Stuck DRQ
pcd0: lock door before command: alt=0x58 stat=0x58 err=0x100 loop=64001 
phase=2
pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
loop=64001 phase=2
pcd0: generic packet before command: alt=0x58 stat=0x58 err=0x100 
loop=64001 phase=2
pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
loop=64001 phase=2
pcd0: unlock door before command: alt=0x58 stat=0x58 err=0x100 
loop=64001 phase=2
pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
loop=64001 phase=2

and at this point the drive's stuck and needs a power cycle. I've tried 
all modes available (4-bit, 8-bit, EPP-8, EPP-16 and EPP-32) and delays 
  from 0 to 10 and nothing changes behaviour.

Changing the parallel port type in my BIOS from Normal to EPP to ECP to 
ECP+EPP, no change.

Behaviour was also the same with the drive's original firmware (which I 
can sort of guarentee was the one it originally came with) and its 
current most recent 1.7e firmware.

I even tested a prehistoric 2.2.6 kernel where things were/are the same 
again.

As said, interface works with a different (CD-ROM) drive and drive works 
fine as plain IDE. I haven't been able to test if it works correctly 
under DOS or Windows with its own drivers as I don't have the drivers 
and can't find them online. If anyone has DOS or Windows EP-2000 
drivers; a pointer would be mightely appreciated.

Anyone any idea what this could be? Can patch/debug...

Rene.

Re: [PARIDE] Datastor EP-2000 problem

[Andrew Morton]

On Thu, 29 May 2008 02:04:59 +0200 Rene Herman <rene.herman@keyaccess.nl> wrote:

> Good day.
> 
> Dug up a parallel port CD-RW consisting of a Philips CDD3801 24x/2x/2x 
> ATAPI CD-RW hooked up to a Datastor EP-2000 parallel interface chip.
> 
> The drive has been verified to work correctly when used directly as IDE 
> and the parallel interface has been verified to work correctly with some 
> random other CD-ROM drive. The combination bombs out though.
> 
> The drive is found:
> 
> root@ax6bc:~# modprobe dstr
> root@ax6bc:~# modprobe pcd
> root@ax6bc:~# dmesg | tail -6
> pcd: pcd version 1.07, major 46, nice 0
> pcd0: Sharing parport0 at 0x378
> pcd0: dstr 1.01, DataStor EP2000 at 0x378, mode 4 (EPP-32), delay 1
> pcd0: Master: R/RW 2x2x24
> pcd0: mode sense capabilities completion: alt=0x51 stat=0x51 err=0x60 
> loop=0 phase=3
> pcd0: mode sense capabilities: Sense key: 6, ASC: 29, ASQ: 0
> 
> trying to extract any data from it fails though:
> 
> root@ax6bc:~# dd if=/dev/pcd0 of=/dev/null bs=2048 count=1
> 0+0 records in
> 0+0 records out
> 0 bytes (0 B) copied, 12.5765 s, 0.0 kB/s
> 
> root@ax6bc:~# dmesg | tail -14
> pcd: pcd version 1.07, major 46, nice 0
> pcd0: Sharing parport0 at 0x378
> pcd0: dstr 1.01, DataStor EP2000 at 0x378, mode 4 (EPP-32), delay 1
> pcd0: Master: R/RW 2x2x24
> pcd0: mode sense capabilities completion: alt=0x51 stat=0x51 err=0x60 
> loop=0 phase=3
> pcd0: mode sense capabilities: Sense key: 6, ASC: 29, ASQ: 0
> pcd0: WARNING: ATAPI phase errors
> pcd0: Stuck DRQ
> pcd0: lock door before command: alt=0x58 stat=0x58 err=0x100 loop=64001 
> phase=2
> pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
> loop=64001 phase=2
> pcd0: generic packet before command: alt=0x58 stat=0x58 err=0x100 
> loop=64001 phase=2
> pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
> loop=64001 phase=2
> pcd0: unlock door before command: alt=0x58 stat=0x58 err=0x100 
> loop=64001 phase=2
> pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 
> loop=64001 phase=2
> 
> and at this point the drive's stuck and needs a power cycle. I've tried 
> all modes available (4-bit, 8-bit, EPP-8, EPP-16 and EPP-32) and delays 
>   from 0 to 10 and nothing changes behaviour.
> 
> Changing the parallel port type in my BIOS from Normal to EPP to ECP to 
> ECP+EPP, no change.
> 
> Behaviour was also the same with the drive's original firmware (which I 
> can sort of guarentee was the one it originally came with) and its 
> current most recent 1.7e firmware.
> 
> I even tested a prehistoric 2.2.6 kernel where things were/are the same 
> again.
> 
> As said, interface works with a different (CD-ROM) drive and drive works 
> fine as plain IDE. I haven't been able to test if it works correctly 
> under DOS or Windows with its own drivers as I don't have the drivers 
> and can't find them online. If anyone has DOS or Windows EP-2000 
> drivers; a pointer would be mightely appreciated.
> 
> Anyone any idea what this could be? Can patch/debug...
> 

I don't know of anyone who is likely to investigate this, sorry.  All I
can suggest is that you file it at bugzilla.kernel.org and be very
patient :(