From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1756276AbYFYLsZ (ORCPT ); Wed, 25 Jun 2008 07:48:25 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1753753AbYFYLsP (ORCPT ); Wed, 25 Jun 2008 07:48:15 -0400 Received: from averell.mail.tiscali.it ([213.205.33.55]:46737 "EHLO averell.mail.tiscali.it" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752657AbYFYLsN (ORCPT ); Wed, 25 Jun 2008 07:48:13 -0400 X-Greylist: delayed 316 seconds by postgrey-1.27 at vger.kernel.org; Wed, 25 Jun 2008 07:48:12 EDT Message-ID: <48622F3A.6070801@shiftmail.org> Date: Wed, 25 Jun 2008 13:42:50 +0200 From: kurk User-Agent: Thunderbird 2.0.0.14 (X11/20080505) MIME-Version: 1.0 To: linux-kernel@vger.kernel.org Subject: Bug in MPT Fusion 2.6.26-rc7 unbootable Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Hi all, I'm no kernel expert, I hope I made no mistakes in this report. It seems to me that a bug was added to the MPT Fusion driver in 2.6.26 (rc7). I compiled 2.6.26-rc7 on a machine with controller LSI53C1080 and it cannot boot. Doing the same with 2.6.25, very similar config file, boots without problems. I tried to forward-port the Fusion driver from 2.6.25 to 2.6.26-rc7 by simply copying over the directory drivers/message/fusion/ from 2.6.25 to 2.6.26-rc7 but unfortunately this doesn't compile, so I am stuck not being able to use 2.6.26 on this machine (actually I have not tried versions of 2.6.26 earlier than rc7... I don't have much time now). I connected a serial cable in order to obtain the boot error message. I obtained two of those on different boots. I will paste these at the end of this email. This is the verbose lspci of the controller (obtained with 2.6.25): ---------------------------------------- 01:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) Subsystem: IBM Unknown device 026d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- GSI 24 (level, low) -> IRQ 24 scsi 0:0:0:0: Direct-Access IBM-ESXS DTN018C1UCDY10F S23J PQ: 0 ANSI: 3 target0:0:0: Beginning Domain Validation target0:0:0: Ending Domain Validation target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127) scsi 0:0:1:0: Direct-Access IBM-ESXS DTN018C1UCDY10F S23J PQ: 0 ANSI: 3 target0:0:1: Beginning Domain Validation ... ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 25 (level, low) -> IRQ 25 target0:0:1: Ending Domain Validation target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127) ... hdc: ATAPI 24X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 scsi 0:0:8:0: Processor IBM 25P3495a S320 1 1 PQ: 0 ANSI: 2 target0:0:8: Beginning Domain Validation target0:0:8: Ending Domain Validation target0:0:8: asynchronous Driver 'sd' needs updating - please use bus_type methods sd 0:0:0:0: [sda] 35548320 512-byte hardware sectors (18201 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: cb 00 00 08 sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 0:0:1:0: Attached scsi generic sg1 type 0 scsi 0:0:8:0: Attached scsi generic sg2 type 3 -------------------------------------------------------------------- It is an x86 32bit PC compile. This is the excerpt of the .config file grepping for FUSION ------------------------------------ CONFIG_FUSION=y CONFIG_FUSION_SPI=m CONFIG_FUSION_FC=m CONFIG_FUSION_SAS=m CONFIG_FUSION_MAX_SGE=40 CONFIG_FUSION_CTL=m CONFIG_FUSION_LAN=m # CONFIG_FUSION_LOGGING is not set ------------------------------------ This is the boot error message obtained with serial cable. I left it running for 8 minutes for this. It loops so the message never ends. -------------------------------------------------------------------- ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! BUG: unable to handle kernel NULL pointer dereference at 0000034c IP: [] :mptspi:mptspi_dv_renegotiate_work+0xa/0x9f Oops: 0000 [#1] SMP Modules linked in: ide_pci_generic(+) floppy mptspi(+) mptscsih ohci_hcd tg3 mptbase scsi_transport_spi usbcore serverworks ide_core ata_generic libata scsi_mod dock thermal processor fan thermal_sys Pid: 9, comm: events/0 Not tainted (2.6.26-rc7 #1) EIP: 0060:[] EFLAGS: 00010282 CPU: 0 EIP is at mptspi_dv_renegotiate_work+0xa/0x9f [mptspi] EAX: f7a447c0 EBX: f7429900 ECX: f7a447c4 EDX: c1908988 ESI: f7a447c0 EDI: 0000034c EBP: f7429904 ESP: f7477f80 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process events/0 (pid: 9, ti=f7476000 task=f744d770 task.ti=f7476000) Stack: f744d8e0 c190b260 00000000 c1908984 f7429900 f7a447c0 f885cc54 f7429904 c012f253 f7429900 c012f934 f742990c 00000000 c012f9e8 00000000 f744d770 c0131bdc f7477fc4 f7477fc4 f7429900 c012f934 00000000 c0131b1b c0131ae3 Call Trace: [] mptspi_dv_renegotiate_work+0x0/0x9f [mptspi] [] run_workqueue+0x75/0xf6 [] worker_thread+0x0/0xbf [] worker_thread+0xb4/0xbf [] autoremove_wake_function+0x0/0x2b [] worker_thread+0x0/0xbf [] kthread+0x38/0x5d [] kthread+0x0/0x5d [] kernel_thread_helper+0x7/0x10 ======================= Code: 70 e8 9e f8 ff ff 8b 47 70 e8 44 b7 fe ff 8b 47 70 5a 5b 5e 5f 5d e9 89 f8 ff ff 58 5b 5e 5f 5d c3 55 57 56 53 83 ec 10 8b 78 10 <8b> 2f e8 c7 98 90 c7 66 83 bf 96 02 00 00 00 8b 85 3c 01 00 00 EIP: [] mptspi_dv_renegotiate_work+0xa/0x9f [mptspi] SS:ESP 0068:f7477f80 ---[ end trace e311270f757682e4 ]--- mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT scsi0 : ioc0: LSI53C1030 B2, FwRev=01000e00h, Ports=1, MaxQ=222, IRQ=223 target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed hdc: ATAPI 24X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 mptscsih: ioc0: attempting task abort! (sc=f7862e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h md: raid1 personality registered for level 1 device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! scsi 0:0:0:0: mptscsih: ioc0: completing cmds: fw_channel 0, fw_id 0, sc=f7862e80, mf = f7a62da0, idx=f mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: task abort: FAILED (sc=f7862e80) mptscsih: ioc0: attempting target reset! (sc=f7862e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:0: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: Issue of TaskMgmt failed! mptscsih: ioc0: target reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting bus reset! (sc=f7862e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=4: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: bus reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting host reset! (sc=f7862e80) mptbase: ioc0: Initiating recovery target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:0: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptscsih: ioc0: host reset: SUCCESS (sc=f7862e80) scsi 0:0:0:0: Device offlined - not ready after error recovery target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:1: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: attempting task abort! (sc=f7862e80) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! scsi 0:0:1:0: mptscsih: ioc0: completing cmds: fw_channel 0, fw_id 1, sc=f7862e80, mf = f7a62f80, idx=14 mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: task abort: FAILED (sc=f7862e80) mptscsih: ioc0: attempting target reset! (sc=f7862e80) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:1: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: Issue of TaskMgmt failed! mptscsih: ioc0: target reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting bus reset! (sc=f7862e80) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=4: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: bus reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting host reset! (sc=f7862e80) mptbase: ioc0: Initiating recovery target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:1: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptscsih: ioc0: host reset: SUCCESS (sc=f7862e80) scsi 0:0:1:0: Device offlined - not ready after error recovery target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:2: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: attempting task abort! (sc=f7862e80) scsi 0:0:2:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! scsi 0:0:2:0: mptscsih: ioc0: completing cmds: fw_channel 0, fw_id 2, sc=f7862e80, mf = f7a63160, idx=19 mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: task abort: FAILED (sc=f7862e80) mptscsih: ioc0: attempting target reset! (sc=f7862e80) scsi 0:0:2:0: CDB: Inquiry: 12 00 00 00 24 00 target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:2: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: Issue of TaskMgmt failed! mptscsih: ioc0: target reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting bus reset! (sc=f7862e80) scsi 0:0:2:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=4: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: bus reset: FAILED (sc=f7862e80) mptscsih: ioc0: attempting host reset! (sc=f7862e80) mptbase: ioc0: Initiating recovery target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:2: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:2: mptspi: ioc0: dma_alloc_coherent for parameters failed mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptscsih: ioc0: host reset: SUCCESS (sc=f7862e80) scsi 0:0:2:0: Device offlined - not ready after error recovery target0:0:3: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:3: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:3: FAST-5 WIDE SCSI 2.4 MB/s ST RTI WRFLOW PCOMP (844 ns, offset 68) target0:0:3: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: attempting task abort! (sc=f7862e80) scsi 0:0:3:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - This one I obtained it in 5 minutes in another boot with a very slightly differing .config file (not changing in the MPT Fusion options). You can see that the stack trace is slightly different. -------------------------------------------------------------------- ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry ACPI: Resource is not an IRQ entry mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! BUG: unable to handle kernel NULL pointer dereference at 0000034c IP: [] :mptspi:mptspi_dv_renegotiate_work+0xa/0x9f Oops: 0000 [#1] SMP Modules linked in: ide_pci_generic(+) floppy mptspi(+) mptscsih mptbase scsi_transport_spi ohci_hcd usbcore tg3 serverworks ide_core ata_generic libata scsi_mod dock thermal processor fan Pid: 9, comm: events/0 Not tainted (2.6.26-rc7 #3) EIP: 0060:[] EFLAGS: 00010282 CPU: 0 EIP is at mptspi_dv_renegotiate_work+0xa/0x9f [mptspi] EAX: f783f480 EBX: f7429900 ECX: f783f484 EDX: c1908548 ESI: f783f480 EDI: 0000034c EBP: f7429904 ESP: f7477f80 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process events/0 (pid: 9, ti=f7476000 task=f744d770 task.ti=f7476000) Stack: 00000000 c012cea5 f7429900 c1908544 f7429900 f783f480 f8856c54 f7429904 c012c82a f7429900 c012cee7 f742990c 00000000 c012cf9b 00000000 f744d770 c012f190 f7477fc4 f7477fc4 f7429900 c012cee7 00000000 c012f0cf c012f097 Call Trace: [] queue_delayed_work_on+0x9a/0xa6 [] mptspi_dv_renegotiate_work+0x0/0x9f [mptspi] [] run_workqueue+0x6c/0xe4 [] worker_thread+0x0/0xbf [] worker_thread+0xb4/0xbf [] autoremove_wake_function+0x0/0x2b [] worker_thread+0x0/0xbf [] kthread+0x38/0x5d [] kthread+0x0/0x5d [] kernel_thread_helper+0x7/0x10 ======================= Code: 70 e8 9e f8 ff ff 8b 47 70 e8 44 37 ff ff 8b 47 70 5a 5b 5e 5f 5d e9 89 f8 ff ff 58 5b 5e 5f 5d c3 55 57 56 53 83 ec 10 8b 78 10 <8b> 2f e8 ff cc 90 c7 66 83 bf 96 02 00 00 00 8b 85 3c 01 00 00 EIP: [] mptspi_dv_renegotiate_work+0xa/0x9f [mptspi] SS:ESP 0068:f7477f80 ---[ end trace e7ec2a28a4a72094 ]--- mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT scsi0 : ioc0: LSI53C1030 B2, FwRev=01000e00h, Ports=1, MaxQ=222, IRQ=223 target0:0:0: mptspi: ioc0: dma_alloc_coherent for parameters failed hdc: ATAPI 24X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 mptscsih: ioc0: attempting task abort! (sc=f7858e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h md: raid1 personality registered for level 1 device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! scsi 0:0:0:0: mptscsih: ioc0: completing cmds: fw_channel 0, fw_id 0, sc=f7858e80, mf = f79e2da0, idx=f mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: task abort: FAILED (sc=f7858e80) mptscsih: ioc0: attempting target reset! (sc=f7858e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: Issue of TaskMgmt failed! mptscsih: ioc0: target reset: FAILED (sc=f7858e80) mptscsih: ioc0: attempting bus reset! (sc=f7858e80) scsi 0:0:0:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=4: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: bus reset: FAILED (sc=f7858e80) mptscsih: ioc0: attempting host reset! (sc=f7858e80) mptbase: ioc0: Initiating recovery mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptscsih: ioc0: host reset: SUCCESS (sc=f7858e80) scsi 0:0:0:0: Device offlined - not ready after error recovery target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: attempting task abort! (sc=f7858080) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=1: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! scsi 0:0:1:0: mptscsih: ioc0: completing cmds: fw_channel 0, fw_id 1, sc=f7858080, mf = f79e2f80, idx=14 mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: task abort: FAILED (sc=f7858080) mptscsih: ioc0: attempting target reset! (sc=f7858080) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed target0:0:1: asynchronous target0:0:1: mptspi: ioc0: dma_alloc_coherent for parameters failed mptscsih: ioc0: Issue of TaskMgmt failed! mptscsih: ioc0: target reset: FAILED (sc=f7858080) mptscsih: ioc0: attempting bus reset! (sc=f7858080) scsi 0:0:1:0: CDB: Inquiry: 12 00 00 00 24 00 mptscsih: ioc0: WARNING - TM Handler for type=4: IOC Not operational (0x40008112)! mptscsih: ioc0: WARNING - Issuing HardReset!! mptbase: ioc0: Initiating recovery mptbase: ioc0: WARNING - IOC is in FAULT state!!! mptbase: ioc0: WARNING - FAULT code = 8112h mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000009! mptbase: ioc0: Recovered from IOC FAULT mptscsih: ioc0: bus reset: FAILED (sc=f7858080) mptscsih: ioc0: attempting host reset! (sc=f7858080) mptbase: ioc0: Initiating recovery target0:0:1: mptspi: ioc0: dma_alloc_coherent for par